I have this output from show interfaces command for the fastethernet interface on a 2811 router.
find the causes of the crc and the ignored input errors on the interface?
The interface configuration is:
interface FastEthernet0/0description VLANS_CHILE
no ip address
[Code]....
I use an 1841 router as an internet facing firewall with a 10MB MetroE connection. Lately users started reporting slow internet download speeds and web pages timing out. Bandwidth reports do not show the link as being saturated so I looked at the interfaces on the 1841. The interface connected to the provider shows OK as far as errors but the LAN side of the router shows steadily increasing input errors. It doesn't show any other errors, no CRC, frame, runts, giants or overruns, just generic input errors. What type of errors are those? Nothing is being logged on the console.
I moved the connection to another switch ports and the errors continue. I switched it down to 10MB and also changed the switch and the errors slow down but don't stop. Interestingly, the switch side never shows any errors. What can I do here? I guess it can be a bad interface but that is such a rare thing that I am hesitant to replace the router.
We are facing since one month in our two Cisco WS-C3750G-12S on many interfaces input errors when data transer or ping (ICMP) increase input erros. Not only port 1 but many interface has same issue, i have change new IOS but still same issue, once i have erase startup config but same issue we are facing and finaly i have replace same new switch with the same IOS it's working fine.(c3750-ipservicesk9-mz.122-55.SE4.bin) [code]
View 11 Replies View RelatedMy Expertise with Cisco ASA is Very less. I have observed Input errors in a Couple of Interfaces in Cisco ASA 5540 Firewall. [code] I need to Clear the Input errors on this particular Interface.Will Clear interface GigabitEthernet 0/0 will work?
View 4 Replies View RelatedWhy packets overrun are incrementing on the ASA even when I've only 40Mbps of throughput traffic?All interface are 1000- Full Duplex, both on ASA and on Catalyst3750.I've test the ASA5540 generating GET HTTP, about 40Mbit of traffic.When I use one ingress interface and one egress interface, interface input overrun counter is zero.When I use the same traffic with 3 ingress interfaces(slot0) and 3 egress interfaces(slot1), interface input overrun counter increase(60k overrun in only 2 minutes).
View 4 Replies View RelatedI have an issue with input errors, overruns, and input reset drops on the inside interface of an 5580-40 (v8.2.5: Transparent mode) The box is not stressed at all according to the 'show' commands in the Cisco troubleshooting performance document for PIX/ASA v8.2.5. Nothing stands out because is pretty much normal, nothing (processes, RAM, blocks, IO...) really being highly utilized. I have replaced the 10Gig card and that seemed to work because the rate of errors has gone down tremedously. The next step is to RMA the whole box.My question is what would be the cause of the inside interface to stop processing traffic (I say that because the syslog server stops receiving messages) for some periods of 30 seconds periodically throughout the day and clients lose their connections (ie Outlook, IBM Sametime, Oracle, MSSQL..etc). Can the issue be somewhere related to the overruns and input errors?
View 2 Replies View RelatedI have been making effort to solve frequent input errors of module interface(WS-X4548-GB-RJ45) in our Backbone Switch(Cat4506).Let me show you show interface information.Rx-No-pkt-buff value is increased continuously even though traffic rate of interfaces is lower than 20Mbps.We have two Backbone Switch which is operated by HA via HSRP.What bring buffer shortage to our network ? [code]
View 2 Replies View RelatedI have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
My router, a Cisco 7204 with NPE 300, is experiencing output drops and input errors on a fastethernet interface. I have a 100Mbps connection with less than 15Mbps utilization at peak times.
FastEthernet1/0 is up, line protocol is up Hardware is DEC21140, address is 0014.a985.1a1c (bia 0014.a985.1a1c) Internet address is 38.102.66.134/30 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 3/255, rxload 1/255
[Code]....
I ran into a problem a few weeks ago and am still trying to figure out why either the 3560 switch or our Cacti syslog server did not alert us when one of our ports was experiencing heavy CRC and Input errors.
I had upgraded the IOS to 12.2(55)SE6 and rebooted the switch. About a week later, someone was troubleshooting why print jobs were having problems printing to a high speed printer. When I looked at the interface it showed a few thousand CRC and Input errors. I cleared the counters and had them print again and watched as the CRC and Input errors went up. When I did a "show log" there were no error messages. Looking at our Cacti Syslog there were also no errors present for the past 6 months.
We found that the device on the port was set to auto speed and duplex and the switch port was at 100/Full. Once we got them to match the problem was resolved, but we were left wondering why we never got any alerts.
We also have some 3548 and 3550 model switches that Cacti picks up %LINK-4-ERROR for any ports that show CRC and Input errors. I did some research and it appears that the 3560 switches do not have the LINK facility code. I believe it has been replaced with a PHY link code but I'm not sure. We do have some "%PHY-4-EXCESSIVE_ERRORS: Excessive FCS, data, or idle word errors found" but they are all for 3750 switches. I could not find any 3560 that had alerted for that error or the LINK error.
I also tripped port security on the 3560 switch just to make sure that it was reporting correctly to Cacti and that alert did show up.
My question is how do I get a 3560 switch to alert in the logging buffer for CRC/Input/FCS errors? Also, how I can generate CRC and Input errors on purpose for testing? I tried mismatching the speed/duplex/Auto and only got collissions, no CRC or Input errors.
I am not sure why the CRC and input errors are increasing in fastethernet port...This port is used as Intradomain cross connect to Data Center service provider for LAN extension between two Data Centers in different locations... The link is 100 MB. The switch port is directly connected to patch panel of DC provider and I believe they have some L3 switch or some other device that is providing LAN extension...
#sh interfaces fastEthernet 0/23
FastEthernet0/23 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0019.3050.1497 (bia 0019.3050.1497)
Description: ASA_VPN_TO
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
[code]....
I'm using a Cisco 1812 to route traffic from a small location with 10 users.. Users are complaning about packet loss, and programs with live database connection is freezing..On the router i've checked one of the Fastethernet interfaces, and I can see that the input errors are increasing constantly. [code]
View 5 Replies View RelatedI am not sure why the CRC and input errors are increasing in fastethernet port...This port is used as Intradomain cross connect to Data Center service provider for LAN extension between two Data Centers in different locations... The link is 100 MB. The switch port is directly connected to patch panel of DC provider and I believe they have some L3 switch or some other device that is providing LAN extension...
#sh interfaces fastEthernet 0/23
FastEthernet0/23 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0019.3050.1497 (bia 0019.3050.1497)
[Code].....
I have an ASR 1002x connected to a 6513. Connection is from ASR Gig Copper SFP to 6513 Copper 10/100/1000 port. The ASR is recevinig Runt and input errors. I have removed the negotiation auto command on both boxes and hard coded the speed etc and still errors occur. I have also added the negotiation auto to both devices and also removed it with out hard coding the speed at and same results. Everytime I have seen these errors is has been to collision caused by a duplex mismatch.
View 4 Replies View RelatedI have an odd situation where I cannot get a device connected to a built in switchport with out input and crc errors. When connecting to a GLC-T sfp it works fine.Here is my test layout
Outdoor wireless AP --- 10' of cat6 cable --- Gigabit POE injector --- 10' Cat6 cable --- 3560G port 48. (input and crc errors)
When I do this there are input and crc errors on the switch port. This has been confirmed on three different switches and three different outdoor AP's. We though at first it was the injector, but when we run the same setup, but instead connect the device to port 49 with a GLC-T sfp there are no errors.
Outdoor wireless AP --- 10' of cat6 cable --- Gigabit POE injector --- 10' Cat6 cable --- 3560G port 49 (GLC-T). (No errors)
I have upgraded the 3560G to the latest ios and still it has the same problem. If I run the same setup to a 2960 there are no errors at all.
Outdoor wireless AP --- 10' of cat6 cable --- Gigabit POE injector --- 10' Cat6 cable --- 2960 port g0/1 (No errors)
I have also tried manually setting the speed on the 3560G with no success.
We're seeing a strange issue with a Cisco 819 that we're testing out. We are able to ping out over the Cellular interface just fine, but as soon as we plug a device into one of the FastEthernet ports we immediately drop the cell connection. The Cell interface then continues to bounce until we unplug the device. We are intending to setup a VPN tunnel, but we've even stripped all that out for the sake of troubleshooting.
Current configuration : 2832 bytes
!
version 15.2
[Code].....
Our 2811 Edge router is having extremely high CPU problems. IP Input is consuming 70% of the process during business hours. Cisco express forwarding is enabled. It only shows 50% but its currently before business hours. Id say even 50% is still high.
CPU utilization for five seconds: 55%/16%; one minute: 70%; five minutes: 76%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
104 5310320 2813117 1887 36.92% 46.73% 51.43% 0 IP Input
The below interface is our public interface and is constantly over utilized with 100% Is there any configurations that can be done to correct this? Is there any more information that is needed?
IOS: (C2800NM-ADVSECURITYK9-M), Version 12.4(24)T4
Show IP Interface
FastEthernet0/0 is up, line protocol is up
Internet address is x.x.x.x
Broadcast address is x.x.x.x
Address determined by non-volatile memory
[code]....
We are having Cisco ASA 5540 having Cisco Adaptive Security Appliance Software Version 8.0(5)23 at certain time of moment daily wer are facing latency and packetdrop wherin when I checked for ASA Interface which gives me " Input Errors" on outside interface ,so can any one tell me what are the causes to get input errors on cisco asa outisde interface.
View 2 Replies View RelatedI have 2 connections a single T1 for voip traffic only and a DSL line for data traffic.the dsl was migrated to a 2811 with out any issues now comes the time to move the T1 over.
on the T1 side I am able to ping the WAN router and the LAN router IP address but nothing behind it.
currently this is the only statment on the router:
ip route 0.0.0.0 0.0.0.0 Dialer1
as a quick a dirty to remove the above i tried:
no ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 66.55.110.0 255.255.255.0 Dialer1
but the DSL side dropped. we have a 66.55.110.152/29
for the T1 i would use the following statement.. we have a 209.98.53.192/27
ip route 209.98.53.0 255.255.255.255 65.32.70.177
i have an 2921 connected to an Catalyst 3560. My router interface shows quite a lot of input queue drops. Load is not too much max 5/255.
View 1 Replies View RelatedWe are facing output queue problems on our ATM interfaces. A lot of output queue errors are been shown as below.
Cisco 2811 -> ATM Link -> <-ATM Link <- Cisco 3945 Routers.
Cisco 2811 Version is 124-15.T9.bin
Cisco 3945 Version is SPA.150-1.M1.bin
Cisco 2811 Output Errors
No date in the TOP-N Interface Errors portlet showing in LMS 4.1, but data for TOP-N Interface Utilization is displayed like expected. The Interface Errors poller show active(without errors) with same Instances as Interface Utilization.
View 1 Replies View RelatedI have a 2911 router connected to two different ISP. Is it posible to route traffic based on what interface the traffic came first?Lets say I have the deault route to use interface gig0/0(ISP1), but a certain ip packet reach the router by interface gig0/1(ISP2). Is there any way (if possible without using source NAT) that I could route traffic back to that ip address using interface gig0/1. The source Ip addresses are not fixed, so I can not use Policy Based Routing.
View 1 Replies View RelatedVlan interface would be dropping packets on the input queue? Refer to the drops/flushes below. This is from a 6500 with a Sup720, there are a number of vlans on it. This 6500 and it's HSRP partner are exhibiting the same symptoms on all the vlans I bothered to check. This particular vlan is quite lightly used, there are only about fifteen user PC's (each with 100 Mb interfaces) on it.
There is a bit of information on input queue drops on Cisco, but this is focused on physical interfaces where I can understand some packets being dropped. I would think that Vlan interfaces would have different issues.I note the "no buffer" errors as well, that also concerns me, especially as that counter is quite close to the "flushes".
Vlan123 is up, line protocol is up Hardware is EtherSVI, address is 00d0.04fd.6000 (bia 00d0.04fd.6000) Description: Vlan123 Internet address is 10.123.123.7/24 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not supported ARP type: ARPA, ARP Timeout 04:00:00
[Code] .......
I have a PIX 535 connected through OFC to Cisco 2960 Switch.
PIX end - G0 (SC type Connector) - Switch End - Gi1/0/28 (LC type connector)
When I am pinging from either side, I am getting packet drops. CRC error is increasing at PIX interface.
Speed settings, tried with
auto - auto
auto - nonegotiate
nonegotiate - auto
nonegotiate - nonegotiate
But no improvements. When its connected with SC - SC connector, its working fine.
Switch also working fine when connected LC - LC.Switch OS is 15.x version.
Cisco PIX Security Appliance Software Version 7.0(4) <system>
Device Manager Version 5.0(4) Cisco PIX Security Appliance Software Version 7.0(4) <system>Device Manager Version 5.0(4)
I have to bridge 1400 series which in the virtual interface has a CRC errors, i don´t the reason, maybe the link (point-point bridge) is misaligned.
View 3 Replies View RelatedI am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedOur customer get the problem that the switch count the 5mins input/output rate of connected traffic interface always ZERO.The problem only occur in the module 3,4 and 5 interface, module 2 has no problems.
-------------------------------------------------------------------------------------------------
Catayst 4506E
12.2(52)SG
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E 2 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 3 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E 4 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E 5 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E
[code]....+
We have 2.5 Mbps connection from an ISP at our branch routers (1800 series)with single physical link terminated on FE0 but have two subinterfaces with separate subnets.
I have applied the following policy-map outbount under physical Interface FastEthernet 0. Show poliocymap output is as follows
Policy Map QoS-OUT
Class Email
priority 512 (kbps)
Class SQL
priority 512 (kbps)
Class File-Copy
police cir 1024000 bc 32000
conform-action transmit
exceed-action drop
Class CCTV
police cir 384000 bc 12000
conform-action transmit
exceed-action drop
But it seems that sometimes( not all the time ) the CCTV traffic seems to exceed the 384k and chokes the entire link(2.5 mbps).
I have a AIR-AP1121G-A-K9 running c1100-k9w7-tar.123-7.JA2 (Autonomous)We have monitoring setup with Orion NPM and we consistently see output errors, Transmit discards and big buffer errors The users at the site have not reporting any issues but was wondering how to prevent these or are these normal?What causes the output errors on Wireless Radio ? How to troubleshoot further ?
Radio0-802.11G
Total Output Errors 0 47749
Small Buffer Misses
4 misses
139 misses
[code]....
Today I've received reports of slow internet access/activity and have noticed myself that it seems a bit slow today. On the dashboard of our asa 5510 the "outside interface" traffic usage is running constantly high. It's at the top of the graph. How can I tell what is causing the spike in utilization. It usually runs at about 1500-2000 Kbps, and now it's up over 10,000.
View 6 Replies View RelatedI'm seeing on an IOS VPN Tunnel interface which keeps going down and then back up...
We have a Cisco 2811 acting as a VPN Hub router on the backbone, which connects to various client sites over VPN. Of the 7 VPNs configured so 6 work well and are generally trouble free. The VPN interface on the other VPN keeps going down ,multiple times throughout the day, just recently the client has been noticing loss of connectivity. The remote router is managed over the VPN so there is always some kind of traffic over it.
*Sep 7 06:40:53.631: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel111, changed state to down
*Sep 7 06:41:23.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel111, changed state to up
[Code]......
Attached is our network diagram showing the details of our remote office and the corporate side which are connected via private fiber. The workstation (10.10.102.84) can ping the 10.20.0.31 IP address of the PBX but not the .30 address and I know if we can’t ping it we can’t remotely manage it. The 2811 router, ASA 5510 and the 6509-E can ping both IP addresses on the PBX. The ASA logs the error "Denied ICMP type=0, from laddr 10.20.0.30 on interface inside to 10.10.102.84: no matching session" when the workstation pings the .30 address.
We changed the default gateway of the PBX from 10.20.0.2 to 10.20.0.1 (2811 router) and we were able to ping both IP addresses from the workstation but the SIP trunks from the Internet stopped working (they NAT to the .30 address). Because calls may be forwarded from the PBX to the corporate network (via IP phones) we will eventually need to change the default gateway to10.20.0.1 and still need the Internet SIP trunks.
My two questions are, how do we resolve the issue of pinging the .30 address from the workstation and then when the time comes how do we resolve the issue with the SIP traffic reaching the .30 address when we change the default GW of the PBX to the 10.20.0.1 address of the 2811 router.