Cisco Wireless :: Interface Radio0-802.11A With CRC Errors 1400 Series
Nov 1, 2011I have to bridge 1400 series which in the virtual interface has a CRC errors, i don´t the reason, maybe the link (point-point bridge) is misaligned.
View 3 Replies
ADVERTISEMENT
Cisco :: Can Two Different Models Of 1400 Series Bridge Communicate
Sep 24, 2012We have acquired few AIR-BR1410A-A-K9 AP's that are for US only. I am in Pakistan. For our market, Cisco proposed AIR-BR1410A-E-K9. This is fine as it is listed on their website as well.However, since we also have the "A" model and now the "E" model, can we place an A model on one end and an E model on the other and make them communicate with each other?
View 3 Replies View RelatedCisco :: Make Bridge Connection Between Aironet 1400 Series And R5005?
May 23, 2013Can we make a bridge connection between cisco aironet 1400 series and cisco R5005? In Root and Non Root Manner.
View 1 Replies View RelatedCisco Application :: Make Bridge Connection Between Aironet 1400 Series And R5005?
May 23, 2013can we make a bridge connection between cisco aironet 1400 series and cisco R5005?
In Root and Non Root Manner.
Cisco Wireless :: Output Errors / Transmit Discards And Big Buffer Errors On 1121 AP?
Sep 13, 2011I have a AIR-AP1121G-A-K9 running c1100-k9w7-tar.123-7.JA2 (Autonomous)We have monitoring setup with Orion NPM and we consistently see output errors, Transmit discards and big buffer errors The users at the site have not reporting any issues but was wondering how to prevent these or are these normal?What causes the output errors on Wireless Radio ? How to troubleshoot further ?
Radio0-802.11G
Total Output Errors 0 47749
Small Buffer Misses
4 misses
139 misses
[code]....
Cisco :: TOP-N Interface Errors Not Showing In LMS 4.1
Dec 4, 2011No date in the TOP-N Interface Errors portlet showing in LMS 4.1, but data for TOP-N Interface Utilization is displayed like expected. The Interface Errors poller show active(without errors) with same Instances as Interface Utilization.
View 1 Replies View RelatedCisco WAN :: Input Errors On 1841 LAN Interface
Nov 4, 2011I use an 1841 router as an internet facing firewall with a 10MB MetroE connection. Lately users started reporting slow internet download speeds and web pages timing out. Bandwidth reports do not show the link as being saturated so I looked at the interfaces on the 1841. The interface connected to the provider shows OK as far as errors but the LAN side of the router shows steadily increasing input errors. It doesn't show any other errors, no CRC, frame, runts, giants or overruns, just generic input errors. What type of errors are those? Nothing is being logged on the console.
I moved the connection to another switch ports and the errors continue. I switched it down to 10MB and also changed the switch and the errors slow down but don't stop. Interestingly, the switch side never shows any errors. What can I do here? I guess it can be a bad interface but that is such a rare thing that I am hesitant to replace the router.
Cisco Firewall :: 2960 Switch - CRC Errors At PIX 535 Interface
Dec 14, 2011I have a PIX 535 connected through OFC to Cisco 2960 Switch.
PIX end - G0 (SC type Connector) - Switch End - Gi1/0/28 (LC type connector)
When I am pinging from either side, I am getting packet drops. CRC error is increasing at PIX interface.
Speed settings, tried with
auto - auto
auto - nonegotiate
nonegotiate - auto
nonegotiate - nonegotiate
But no improvements. When its connected with SC - SC connector, its working fine.
Switch also working fine when connected LC - LC.Switch OS is 15.x version.
Cisco PIX Security Appliance Software Version 7.0(4) <system>
Device Manager Version 5.0(4) Cisco PIX Security Appliance Software Version 7.0(4) <system>Device Manager Version 5.0(4)
Cisco Switching/Routing :: Input Errors On Many Interface WS-C3750G-12S
Apr 16, 2013We are facing since one month in our two Cisco WS-C3750G-12S on many interfaces input errors when data transer or ping (ICMP) increase input erros. Not only port 1 but many interface has same issue, i have change new IOS but still same issue, once i have erase startup config but same issue we are facing and finaly i have replace same new switch with the same IOS it's working fine.(c3750-ipservicesk9-mz.122-55.SE4.bin) [code]
View 11 Replies View RelatedCisco Firewall :: How To Clear Input Errors In ASA5540 Interface
Feb 26, 2013My Expertise with Cisco ASA is Very less. I have observed Input errors in a Couple of Interfaces in Cisco ASA 5540 Firewall. [code] I need to Clear the Input errors on this particular Interface.Will Clear interface GigabitEthernet 0/0 will work?
View 4 Replies View RelatedCisco Security :: ASA5540 Interface Input Errors - Overrun
Nov 16, 2009Why packets overrun are incrementing on the ASA even when I've only 40Mbps of throughput traffic?All interface are 1000- Full Duplex, both on ASA and on Catalyst3750.I've test the ASA5540 generating GET HTTP, about 40Mbit of traffic.When I use one ingress interface and one egress interface, interface input overrun counter is zero.When I use the same traffic with 3 ingress interfaces(slot0) and 3 egress interfaces(slot1), interface input overrun counter increase(60k overrun in only 2 minutes).
View 4 Replies View RelatedCisco WAN :: Input Errors On Fastethernet Interface Router 2811
Feb 22, 2012I have this output from show interfaces command for the fastethernet interface on a 2811 router.
find the causes of the crc and the ignored input errors on the interface?
The interface configuration is:
interface FastEthernet0/0description VLANS_CHILE
no ip address
[Code]....
Cisco Firewall :: 5580-40 - Input Errors / Overruns And Reset Drops On 10Gig Interface?
May 10, 2012I have an issue with input errors, overruns, and input reset drops on the inside interface of an 5580-40 (v8.2.5: Transparent mode) The box is not stressed at all according to the 'show' commands in the Cisco troubleshooting performance document for PIX/ASA v8.2.5. Nothing stands out because is pretty much normal, nothing (processes, RAM, blocks, IO...) really being highly utilized. I have replaced the 10Gig card and that seemed to work because the rate of errors has gone down tremedously. The next step is to RMA the whole box.My question is what would be the cause of the inside interface to stop processing traffic (I say that because the syslog server stops receiving messages) for some periods of 30 seconds periodically throughout the day and clients lose their connections (ie Outlook, IBM Sametime, Oracle, MSSQL..etc). Can the issue be somewhere related to the overruns and input errors?
View 2 Replies View RelatedCisco Switching/Routing :: WS-X4548-GB-RJ45 Frequent Input Errors Of Module Interface
Oct 21, 2012I have been making effort to solve frequent input errors of module interface(WS-X4548-GB-RJ45) in our Backbone Switch(Cat4506).Let me show you show interface information.Rx-No-pkt-buff value is increased continuously even though traffic rate of interfaces is lower than 20Mbps.We have two Backbone Switch which is operated by HA via HSRP.What bring buffer shortage to our network ? [code]
View 2 Replies View RelatedCisco Wireless :: 4400 Series Controller Blocking 802.11a/n Radio Interface Of 1250 AP
Dec 19, 2009We are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies View RelatedCisco WAN :: Can Do Sub-interface In 891 / 881 Series Router
Jun 18, 2012Can i do sub-interface in cisco 891 or 881 series router ? 1900 and 2900 series router support sub-interface ?
View 1 Replies View RelatedCisco Wireless :: Aironet 1400 Bridge FIPS Compliance?
Aug 14, 2012Is the Aironet 1400 bridge FIPS 140-2 compliance? Based on the Release 12.3(8)JA, the Cisco IOS software release 12.3(8)JA is undergoing FIPS 140-2 Level 2 validation. Does it mean it is FIPS 140-2 compliance with this software level to run on Aironet 1400 bridges? [URL]
View 1 Replies View RelatedCisco WAN :: Configuring 870 Series Router ATM Interface
Nov 24, 2011I have configured Cisco 870 router ATM interface with following configuration
interface atm 0
ip address public ip 255.255.255.254
ip nat outside
pvc 0/38
encapsulation aal5snap
no shutdown
But when I check ATM interface it is still down and line protocol is down. how to make it up and up so that internet service could be used.Also I want to know that the provider has also given username and password for internet in their device.We want to replace that device with the router and facing problems.
Cisco Wireless :: Results From Dot11 Link Test On 1400 Bridges?
Sep 11, 2012Just did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?
View 9 Replies View RelatedDell Vostro 1400 Laptop Unable To Use Wireless Internet?
Jun 11, 2011Today after I restarted my laptop (Dell vostro 1400 running windows), I found that I can't open any pages or sites. My wireless utility icon tells me that my laptop is connected to my router, but neither of my browsers (chrome or firefox) will load anything. However, if I turn off my wireless (there's a switch that I can trigger) and try to load a page immediately after turning it back on, then a page will load, though anything after that will not. I'm positive that it's not my router or my internet because my computer and iPod touch connect perfectly fine, it's just my laptop will not.I thought that I might have accidentally gotten malware so I ran malwarebytes in safe mode and it found one Trojan, which I removed afterwards, though I don't remember what it's name or type was. I restarted my laptop afterwards hoping that removing the Trojan would work but I'm still having the same problem.
View 1 Replies View RelatedDell :: Vostro 1400 / Wireless - Smart Phone Hotspot?
Jan 5, 2012I have a Vostro 1400 and my OS is Windows XP. I just bought an Android Smart Phone, my carrier is Sprint.
I have portable ‘Hot Spot’ service. However, I can’t find a wireless program on my computer.
I swapped out my original hard drive after it crashed. I thought that I reloaded everything onto the new one.
Cisco WAN :: 7600 Series SPA Interface Processor-600 Compatibility
Oct 3, 2012does the Cisco 7600 Series SPA Interface Processor-600 (7600-SIP-600-DC) only support a single SPA, e.g. 1 x SPA-OC192POS-XFP?
The 10Gbps through put on the 7600-SIP-600-DC and [URL]to show that this is the case.
Dell :: Vostro 1400 Cannot Access Any Wireless Or Network Via Hard Wire
Sep 5, 2012Today I replaced my motherboard to fix the graphics card issue on my Vostro 1400. After installing the motherboard I installed the driver's from Dell's site for the networking card.
I get an error stating device driver/software was not successfully installed. I tried a restore point, that didn't work either. I tried the original driver disc that came with the laptop - same problem.
In device manager it is showing: broadcom netlink adapter fast ethernet #2 - does that mean it thinks I have more than one network card? I'm not sure what to do next. I can't access any wireless from that laptop, not even from a hard wire.
I'm running Windows 7 32 bit.
Cisco WAN :: Interface Embedded-Service-Engine In 1900 Series
May 3, 2011Sure this is a simple one. New to the 1900 series routers, have a 1921 with IOS 15.1. Noticed that there is a standard interface labeled Embedded-Service-Engine0/0. What the purpose of this is? Cannot seem to find any detail on it. See extract from default config below.
View 5 Replies View RelatedCisco WAN :: Routing Based On Source Interface FE01 Series
Jun 6, 2011I am looking for a config, as per the attached diagram, if the traffic comes from FE01 it should go via FE03 for the internet and when the traffic comes from FE02 it should go via FE04 for the internet.
View 1 Replies View RelatedCisco WAN :: Duplex Setting On WAN Interface On ASR 1000 Series Router
Apr 13, 2013I have autonegotiation disable on my interfcae what should be duplex setting on other end?
Router#sh run int Gi0/3/0
Building configuration...
Current configuration : 334 bytes(code)
Cisco WAN :: 1900-3900 Series Router With 100FX Fiber Interface
Oct 30, 2011Is there a router (1900-3900 series router) that will support a 100FX fiber connection. We use to use 2800-3800 and 2600-3700 series routers with FX fiber interface now these routers are no longer available and our need for 100Mbps FX is still a requirement.
View 3 Replies View RelatedCisco Switching/Routing :: Router 800 Series Interface Cellular0 Keeps Bouncing Up / Down
Aug 6, 2012I was able to setup my router c819 with Verizon 3G but there is one minor thing that on the console it keeps saying:
Aug 7 21:04:30.067: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
Aug 7 21:04:35.111: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
Aug 7 21:06:18.423: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
The interface Cellluar0 is connected to Verizon 3G network and I'm able to ping and get to the internet just fine. I did few research and some people said it was access list. My ACL is below but I can't find anything wrong with it.
!
!
interface Cellular0
ip address negotiated
[Code].....
Cisco WAN :: 6500 Series Switch / Configured Port Channel On Both Switches With 2 Gig Interface
Jan 9, 2012we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
Cisco Switching/Routing :: Does Supervisor 720 Support All Existing Catalyst 6500 Series Interface
Feb 12, 2013Q. Does the Supervisor 720 support all existing Cisco Catalyst 6500 series interface and services module, protecting customer investments?
View 1 Replies View RelatedCisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series
Mar 6, 2012Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedCisco Wireless :: 1140 AP Series Vs 1260 AP Series Technical Differences
Jul 24, 2012What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedCisco Wireless :: 1400 - Equipment Cannot Bridge To Other Root Or Not-root Mode
May 3, 2013We have a problem with a Cisco 1400 Bridge. This equipment can not bridge to the other root or not root mode. I can see a message "Interface Dot11Radio0 Radio transmit power out of range" and the MAC Address of Dot11Radio0 appears with 0000.0000.0000.I set the local power to 18 but the MAC Address is still in 0000.0000.0000.
View 1 Replies View Related