We have acquired few AIR-BR1410A-A-K9 AP's that are for US only. I am in Pakistan. For our market, Cisco proposed AIR-BR1410A-E-K9. This is fine as it is listed on their website as well.However, since we also have the "A" model and now the "E" model, can we place an A model on one end and an E model on the other and make them communicate with each other?
View 3 RepliesCan we make a bridge connection between cisco aironet 1400 series and cisco R5005? In Root and Non Root Manner.
View 1 Replies View Relatedcan we make a bridge connection between cisco aironet 1400 series and cisco R5005?
In Root and Non Root Manner.
are there any AP models which support 5500 series and dont support 4400 series. Actually we are looking to get some new AP with higher bandwidth and External Antenna How to differentiate between AP models with clean air feature supported and not
View 5 Replies View RelatedI have some problem with 802.11A radio is enabled but the detaild status is still display software status is disabled and hardware status is down. I checked the settings on Enable Radio is checked on enable. I can't get any radio accross. whereelse I can check to get this working?
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
power local 18 <<<<<<<<<<< I can't input this line from the command line. I assume that the bridge is taking the MAX setting.
power client 18
packet retries 128
station-role non-root
rts threshold 4000
rts retries 128
concatenation
beacon period 20
infrastructure-client
I have to bridge 1400 series which in the virtual interface has a CRC errors, i don´t the reason, maybe the link (point-point bridge) is misaligned.
View 3 Replies View RelatedIs the Aironet 1400 bridge FIPS 140-2 compliance? Based on the Release 12.3(8)JA, the Cisco IOS software release 12.3(8)JA is undergoing FIPS 140-2 Level 2 validation. Does it mean it is FIPS 140-2 compliance with this software level to run on Aironet 1400 bridges? [URL]
View 1 Replies View RelatedCan I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedWe have a problem with a Cisco 1400 Bridge. This equipment can not bridge to the other root or not root mode. I can see a message "Interface Dot11Radio0 Radio transmit power out of range" and the MAC Address of Dot11Radio0 appears with 0000.0000.0000.I set the local power to 18 but the MAC Address is still in 0000.0000.0000.
View 1 Replies View Related I have mounted a cisco 2950G series switch in the network. we are working on Multicasting so I have LAN connectivity from one location ot other.
Situation:- 1- we do not have to do anything at remote location. its already done with final configuration and working fine because we other location witch are connected with this same HP switch at remote site and working fine but problem is only with one location where I have changed switch(cisco2960). when i connect cable from MUx to the switch cisco switch (Local) on particular port its does not response (LED continuously glowing amber color and does not go to green color) and communication does not start.for fixing this issue I have done so many things, vlan, duplex, speed- done everything but response.
situation 2:-when I changed this cisco device and use any other vendor's switch whether its manageable not manageable its get start proper communication. so I am unable to figure out whats the issue with. is there new or latest switch are not compatible with other vendor.
I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox
View 1 Replies View RelatedI am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch. The port is setup as a trunk with a native vlan of 2 (our management vlan). [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating. No other entries. If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats. Similar for "Power Injector Port 1". Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?
View 3 Replies View RelatedI am intetested in Cisco 2960 ttl models, but need to justify my choice over other brands.What are the equivalent models from netgear, Dlink and HP.
View 1 Replies View RelatedWhen two Routers Models 1941 (Main Router) and 1841 work connected with HSRP, and a second LAN card is added to each one of them If i connect the GE 0/1 and Fe 0/1 of each of one of them To FireWall1 (in cluster with FireWall2) AND i connect the second LAN (Added) of each one To FireWall2 (in cluster with FireWall1) If FireWall1 will failure , How can Router 1941 know, to move traffic from GE 0/1 to the second LAN card connected to FireWall2 (which is in charge now, by cluster definition)
View 2 Replies View RelatedWe are considering order the AP541N for our network. A few questions...
1). Are there multiple models of the AP541N? or just one cisco part number?
2). I am assuming the basic antenna comes with it. If this is something that I need to buy seperate.
3). Are there part numbers for the POE injector? Need to know part numbers on the AP541N and the poe injectors?
4). We would buy a couple of these and run them in cluster mode. My understanding is that I won't need a controller. Do I need to buy a certain model to use the clustering or is that available on all the AP541N?
5). Can I have this talk to active directory to authenticate users? Is that tough to do? Do I need install some kind of agent on a domain controller? I have configured the ASA to use Active Directory for authentications. Should it be any more difficult that that?
I have setup a few other Cisco APs before and am generally familair with wireless. But, I am not a "wireless expert" and don't have any experience with this particular product.
We are looking at doing some switch replacement. These switches will be in for ~7 years.We need POE for a VOIP phone system, and 10gb uplinks back to the core. We want to have the ability to go POE+ in the future.
We were quoted from our vendor for:WS-C3850-48P-S with 2x715w Power supplies. It looks like the data sheet says that to get POE+ you need 2x1100w or 1x1100w & 1x715w. Do we need to step up to the WS-C3850-48PF-S?
I am using a GRE-IPSEC tunnel configuration + EIGRP routing protocol and I would like to confirm if I am right with the following:
Due to I am configuring the IP MTU = 1400 in the Tunnel interface, I am avoiding additional fragmentation after GRE encapsulation because there is enough room for IPSEC encapsulation (no matter which mode I am using - I am considering the worst case Tunnel Mode). However, I would like to know what happens if I ALSO include in the Tunnel configuration the command ip tcp adjust-mss 1360 which is clear operates in layer 4 during the 3 way handshaking process to establish the TCP connection/session between opposite hosts (in this case the interaction is with the respective end routers). By adding this MSS command, I understand that I could also eliminate the initial fragmentation of the 1500 bytes LAN packets (before GRE encap) because the hosts are notified to send 1360 bytes packets to the Router and based on the previous, I would be able to transfer packets without "theorical" fragmentation between both ends.
One more question, how can affect if I include this additional command (TCP ADJUST-MSS) the performance (process + memory) of a router 3845 or 7200 without producing for example a entire crash of the device???. I understand that this TCP MSS negotiation is router process intensive but is less than IPSEC encryption/decryption.
(eth ports routing only) and a layer 2 switch into a cluster of two layer 3 switch clustered. I have looked at Cisco 3550 EMIs with HSRP but I would like to implement based on newer models of Cisco switches.
View 6 Replies View RelatedI am planning to build a site to site vpn tunnel, connecting 2-3 satellite office to the main office.After searching the product, I really don't understand the difference between models like the ASA5505 and RV042.Can I need to use ASA5505 in the main office while RV042 in the stallite offices? Or can I use RV042 (or upper) in all the office and it is enough for vpn tunnel?If it is the case, what is the benefit of ASA series over the RV series?
View 1 Replies View RelatedACE 4710 deployment model. We'll be doing an eval later in the year, but I'm just looking to understand the architecture.We have a stack of 3750 switches with a single VLAN (10.1.1.0/24). Connected to that stack is a pair of web servers (10.1.1.5 and 6) that we want to provide load balancing/failover for. Some of the clients are located right there on that same VLAN. Other clients may be coming from other spots in the infrastructure.It sounds like I could put a pair of 4710s connected to that stack of switches, in a single arm deployment? And then the virtual IP and the real servers would all be 10.1.1.0/24. Maybe use an etherchanel to connect each 4710 to two 3750s?
View 9 Replies View RelatedI have one AP541N and need to extend the wireless network with a second wireless AP. Which models of AP can I use with the AP541N to achieve a 'cluster', please? Is it just with a second AP541N or can I use other Cisco APs to achieve the cluster?
Am I correct in thinking that doing this will allow wireless clients to 'roam' seamlessly between the two APs?
I want to be sure for this before ordering: is the Enterprise-class stackable switches "WS-C3750X-48T-S" model can be stackable with "WS-C3750G-48TS" model.
View 5 Replies View RelatedI am trying to decipher the differences between the two models of the 1921 router. One has an IP Base IOS and the other has a Security IOS. I have an ASA so I don't think I need all the Security IOS bells and whistles on an internal router. Although, does the IP Base IOS allow for trunking and sub interfaces? I definitely need that and on CDW's website it says that the 1921-Sec/K9 w/ Security IOS includes 802.1Q and that spec is not listed on the 1921/K9 IP Base IOS model.
View 3 Replies View RelatedI am able to view clients, rogue APs, rogue clients etc, but the information is faily inaccurate. Thus, I am trying to calibrate using the RF calibration models. I have created a new model and am attempting to add data points.After adding the client MAC, selecting the floor plan and clicking next, the floor plan loads and a message pops up stating: "Could not enable S60 across all relevant controllers on this floor". I click OK, and select "point" as the calibration method. When I place the calibration point on the map and click GO I am presented with the following message: "Failed to initiate data collection. Please make sure your client is connected on the wireless network and then try again." Both of these messages can be seen in the attached screenshots.
I have confirmed that the client is associated to an AP located on the map.I have confirmed connectivity of the client.I have used both the Cisco AIR-CB21AG-W-K9 (CCX V5) and the integrated intel wireless card (CCX V4).I am running WCS 7.0.172.0, MSE 7.0.201.204, and WLC 7.0.116.0.
I was assembling and testing some custom production machines here, and I had to perform a data transfer between two windows 7 machines through an HP 1400 switch. I saw 100MBps transfers for the first time. I only wish I could get the main network to operate that fast.
View 13 Replies View RelatedMy friend has a laptop inspiron 1400.... when he tries to connect the internet, message comes up "unable to connect with yellow icon" but yesterday we played online game.
View 2 Replies View Relatedi have re-installed windows xp in my laptop Dell Vostro 1400. it came with Vista but i have formatted and installed registered xp in it. when i installed WiFi driver in it (downloaded form Dell site), the driver works fine but because of this driver my machine gets stuck right after startup (when its shows the desktop). i was thinking that maybe its windows defect but now i came to know that when i uninstall the driver, it dont stuck.. i have tried a lot of drivers from Dell site. specifically for this model.
View 14 Replies View RelatedJust did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?
View 9 Replies View RelatedI'm adding some additional AP's (3502s) to an environment that is all 1131AG AP's. The DHCP is configured for DHCP option 43 for remote sites for layer 3 discovery. Since only one AP mode can use option 43, I've added a DNS entry for cisco-lwapp-controller in my local domain.My assumption here is that the new 3502's will be able to use DNS for discovery, while any additional 1131AG would continue to use DHCP option 43. will this work in a mixed environment?The new AP briefly showed up on my controller, but then disappeared. The LED is cycling red, green, off - indicating it is still in the discovery process. Could I effectively remove the option 43 in DHCP and have all AP's use DNS? Is this as reliable as option 43? What is the best practice for discovery?
View 6 Replies View RelatedToday after I restarted my laptop (Dell vostro 1400 running windows), I found that I can't open any pages or sites. My wireless utility icon tells me that my laptop is connected to my router, but neither of my browsers (chrome or firefox) will load anything. However, if I turn off my wireless (there's a switch that I can trigger) and try to load a page immediately after turning it back on, then a page will load, though anything after that will not. I'm positive that it's not my router or my internet because my computer and iPod touch connect perfectly fine, it's just my laptop will not.I thought that I might have accidentally gotten malware so I ran malwarebytes in safe mode and it found one Trojan, which I removed afterwards, though I don't remember what it's name or type was. I restarted my laptop afterwards hoping that removing the Trojan would work but I'm still having the same problem.
View 1 Replies View RelatedI have a Vostro 1400 and my OS is Windows XP. I just bought an Android Smart Phone, my carrier is Sprint.
I have portable ‘Hot Spot’ service. However, I can’t find a wireless program on my computer.
I swapped out my original hard drive after it crashed. I thought that I reloaded everything onto the new one.
Region : Argentina
Model : TL-WDR4900
Hardware Version : V1
I am about to buy one of these two models tl-wdr7500 and tl-wdr4900 that look exactely the same and I am trying to figure out what is the difference between them?
Today I replaced my motherboard to fix the graphics card issue on my Vostro 1400. After installing the motherboard I installed the driver's from Dell's site for the networking card.
I get an error stating device driver/software was not successfully installed. I tried a restore point, that didn't work either. I tried the original driver disc that came with the laptop - same problem.
In device manager it is showing: broadcom netlink adapter fast ethernet #2 - does that mean it thinks I have more than one network card? I'm not sure what to do next. I can't access any wireless from that laptop, not even from a hard wire.
I'm running Windows 7 32 bit.