are there any AP models which support 5500 series and dont support 4400 series. Actually we are looking to get some new AP with higher bandwidth and External Antenna How to differentiate between AP models with clean air feature supported and not
View 5 RepliesWe have acquired few AIR-BR1410A-A-K9 AP's that are for US only. I am in Pakistan. For our market, Cisco proposed AIR-BR1410A-E-K9. This is fine as it is listed on their website as well.However, since we also have the "A" model and now the "E" model, can we place an A model on one end and an E model on the other and make them communicate with each other?
View 3 Replies View RelatedThe access point is reply when I ping it from WLC. But until know it can't join, even discovery packet isn't arrive in WLC.
WLC software version = 6.0.199.4
Management interface address = 192.168.120.10 /24
Model = 5508
Access point software = 1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1) AP Model = cisco AIR-LAP1242G-E-K9 Interface address = 192.168.121.151
I have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedThe Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?
Whats it "OfficeExtend support" in the 5500 WLC datasheet?.I dont see nothing about this in the WLC configuration guide release v7.0.116.0.Is this the same as OEAP?. Is the OfficeExtended (or OEAP) supported on the 1140 APs?. If so where can I get a guide to configure this?.
View 2 Replies View RelatedWe have the ASA firewalls in our environment - two 5510's and one 5520.Our 5510's are currently used in our production environment and the 5520 is our firewall for pre-production and support personnel. My question is about the AnyConnect VPN licenses we have. Currently we have 100 seats for AnyConnect on our production ASA's, but we'd like to see if we can move half of these to the 5520 ASA?
View 1 Replies View RelatedSince the 5500X series firewalls use a software IPS SSM that is set up differently from the old ones, I am a little confused on the initial setup.
[URL]
we see a proposed setup for L3 management of the IPS
interface GigabitEthernet0/0
nameif outside security-level 0
ip address 203.0.113.1 255.255.0.0
[Code].....
: %DATACORRUPTION-1-DATAINCONSISTENCY: unterminated string in buffer of length 129, counted: 129 -Traceback= 4027CB2C 402B1E88 4052884C 40528A48 40528D08 40529188 40529358 403247E8 403247D4
Cisco Internetwork Operating System Software
IOS (tm) C5RSM Software (C5RSM-ISV-M), Version 12.2(46), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Thu 26-Apr-07 19:41 by pwade
Image text-base: 0x40010948, data-base: 0x410F41D0
[code]....
Our requirement with that appliance is to do URL blocking and filtering.Are there any other options we can consider or is it SaaS only. Would have preferred Trend Micro, but don't this is possible with this appliance.Will content security be offered on the Cisco ASA 5500-X Series?At this time, content security services are not supported on the Cisco ASA 5500-X Series appliances. However, the ASA 5500-X Series Cisco Cloud Web Security ready. Cisco Cloud Web Security provides content security as a cloud-based software as a service (SaaS).
View 1 Replies View RelatedI bought a 5500 series ASA and SecPlus license for example. Suddenly my ASA hardware got broken and changed for a new one. What about my old license? How i could activate this license on new ASA?
View 2 Replies View RelatedI understand that Cisco have at long last provided a facility to separate HTTP web authentication from HTTPS WLC management on WLC code 7.2.x for the new 5500 series WLCs.
My question is does Cisco intend to provide the same much needed functionality on the 4400 series WLCs that are running 7.0.x code? I was looking through the release notes for v7.0.235.3 code and that did not seem to mention this functionality. I know we can get around the problem by purchasing an SSL certificate so that guest users with web authentication do not have to see the same security warning each time they log in but the idea to separate the HTTP web authentication from HTTPS WLC management seems so much simpler.
I tried looking in ASA documentations but unable to find out that how many IPSec Tunnels can be terminated to an ASA cluster. I have 5545 running only two IPSec Tunnels so far but need to terminate 18 sites all up and would like to confirm how many tunnels we could terminate? Is there a limitaion to it?
View 2 Replies View RelatedDo you know if the new 2500 series controller supports things like mobility groups? Could I use 2 of these and do inter-controller roaming. Also do you know if this would work with a 2106 controller and a 2505 controller or are they 2 completely independent controllers only knowing about their own APs??
View 12 Replies View RelatedDoes 2500 series wireless controllers support redundancy?
View 1 Replies View RelatedWe are working with a contractor to upgrade our network, and I heard from them that the 5596/5548 might not need the Layer 3 module for our inter-VLAN routhing. They have yet to give me an answer.
We do have a few static routes on our current layer-3, core switch too.
I noticed that the 3600 access point series will get an add-on module to support 802.11ac. This standard will support more than 1 GBit/s.But the 3600 series still do only have got one GBit port. Any extended information about 802.11ac in the upcoming Cisco portfolio?
View 8 Replies View RelatedHow many VMs can a pair of 5548s support? Remember, for each VM, I will have an ARP entry in the 5500 ARP Table (assume 5500 is the L3 default gateway).
View 3 Replies View RelatedDoes the Nexus 5548/5596 switch support OSPF ECMP?
Also on OSPF and ECMP, the load-balancing method at the multiple links for Catalyst 3750 is per IP packet or per destination IP?
Nexus 5500 support auto negotiation on 1gig sfp port? There is an end device that only support auto negotiation and cannot be manually set speed/duplex.
View 0 Replies View RelatedAny plans to support REP on the 6500 series?We have Sup 720 with MSFC3.
View 1 Replies View RelatedI'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.
View 1 Replies View RelatedIs there reason why WS-C3560C-8PC-S and WS-C3560C-12PC-S is not supported in Cisco Network Assistent? According to the data sheets for these switches CNA should be supported. I saw another forum post stating that the Gigabit versions has been added to the supported list as of version 5.7."The Cisco Catalyst 3560-C and 2960-C Series compact switches offer both the traditional Cisco CLI for detailed configuration and Cisco Network Assistant software, a PC-based tool for quick configuration based on preset templates."
View 2 Replies View RelatedAm I correct in thinking that 200 series swiches now support SNMP using v1.3?
View 1 Replies View RelatedI was slightly dissapointed with the performance of the "pre-sales" phone number of Cisco in the Netherlands so I am asking it here instead.We decided on using 2 Cisco 2921 routers with 2.5GB ram to use for a MultiHomed connection using BGP. We already have our v4 and v6 space assigned as well as our AS number. The connections should turn up soon.What I could not find out with proper certainty on the Cisco Feature Navigator is if the IP BASE on the Cisco 2921 supports both IPv4 and IPv6 routing combined with BGP. This model uses the Universal IOS licensing which I found slightly confusing. I could not find a simple matrix with the supported commands either.
View 1 Replies View RelatedWe are considering order the AP541N for our network. A few questions...
1). Are there multiple models of the AP541N? or just one cisco part number?
2). I am assuming the basic antenna comes with it. If this is something that I need to buy seperate.
3). Are there part numbers for the POE injector? Need to know part numbers on the AP541N and the poe injectors?
4). We would buy a couple of these and run them in cluster mode. My understanding is that I won't need a controller. Do I need to buy a certain model to use the clustering or is that available on all the AP541N?
5). Can I have this talk to active directory to authenticate users? Is that tough to do? Do I need install some kind of agent on a domain controller? I have configured the ASA to use Active Directory for authentications. Should it be any more difficult that that?
I have setup a few other Cisco APs before and am generally familair with wireless. But, I am not a "wireless expert" and don't have any experience with this particular product.
Does ASR 1000 Series support DMVPN Hub, and Key Server in GETVPN.
View 2 Replies View RelatedWhen will Campus Manager support the 2960S switch series?
View 2 Replies View RelatedDo the SA500 Series Firewalls Support BGP Routing?
View 3 Replies View RelatedI have one AP541N and need to extend the wireless network with a second wireless AP. Which models of AP can I use with the AP541N to achieve a 'cluster', please? Is it just with a second AP541N or can I use other Cisco APs to achieve the cluster?
Am I correct in thinking that doing this will allow wireless clients to 'roam' seamlessly between the two APs?
OSPF normally only comes with IPservices image and not IP Base image. The 3560-C series data sheet says that it only suport IP Base image, yet it mentions that support for OSPF in included. Are there any restictions in the OSPF support?.
View 7 Replies View RelatedI am able to view clients, rogue APs, rogue clients etc, but the information is faily inaccurate. Thus, I am trying to calibrate using the RF calibration models. I have created a new model and am attempting to add data points.After adding the client MAC, selecting the floor plan and clicking next, the floor plan loads and a message pops up stating: "Could not enable S60 across all relevant controllers on this floor". I click OK, and select "point" as the calibration method. When I place the calibration point on the map and click GO I am presented with the following message: "Failed to initiate data collection. Please make sure your client is connected on the wireless network and then try again." Both of these messages can be seen in the attached screenshots.
I have confirmed that the client is associated to an AP located on the map.I have confirmed connectivity of the client.I have used both the Cisco AIR-CB21AG-W-K9 (CCX V5) and the integrated intel wireless card (CCX V4).I am running WCS 7.0.172.0, MSE 7.0.201.204, and WLC 7.0.116.0.
Can any ASA 5500 in particular the ASA5510 firewall support jumbo frames (i.e. greater than the default standard 1500 Bytes frames)?. I plan to use the ASAs to setup a point-to-point IPSec tunnel and need an Application frame of 4Kbytes intact and not segment it.I have done little checking on the Cisco Website and see it mention of Jumbo frames on the 5580 on 10Gig interface but didn't see mention 5510. 5580s are way over-kill and expensive for what I need is to run a mission critical one IPSec point-to-point with maximum of no more than 100Kbps so 5510 is perfect for me but not sure if it can carry the jumbo frame?
On the routers and switches it's the MTU settings and they are configurable per interface and I am OK and the circuit is T1 which the Telcos said it's OK since it's physical layer so the only unkown is the firewall.