Whats it "OfficeExtend support" in the 5500 WLC datasheet?.I dont see nothing about this in the WLC configuration guide release v7.0.116.0.Is this the same as OEAP?. Is the OfficeExtended (or OEAP) supported on the 1140 APs?. If so where can I get a guide to configure this?.
View 2 RepliesThere is a vlan Finance in my office. The requrement : Vlan Finance is allow to access internet and selected host/network and not allow to access internal network. But from internal network can access to Vlan Finance (Full access). I want to configure using Reflexive ACL, but from Datasheet 4500 doesn't support Reflexive ACL. Intervlan routing is in 4500. Is there any ACL configuration to support my requirement without using Reflexive ACL?
View 1 Replies View Relatedare there any AP models which support 5500 series and dont support 4400 series. Actually we are looking to get some new AP with higher bandwidth and External Antenna How to differentiate between AP models with clean air feature supported and not
View 5 Replies View RelatedI know officeextend 600 is for home user. But i wanted to know is it possible for office extend 600 to work in same subnet/vlan of WLC.
View 5 Replies View RelatedI try to configure an AP1131 as OfficeExtend but unfortunately I receive the following message from the debug command on the WLC5508: (Cisco Controller)
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Discovery Request from XX.XX.XX.XX:14847
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Join Priority Processing status =
[Code].....
How many VMs can a pair of 5548s support? Remember, for each VM, I will have an ARP entry in the 5500 ARP Table (assume 5500 is the L3 default gateway).
View 3 Replies View RelatedDoes the Nexus 5548/5596 switch support OSPF ECMP?
Also on OSPF and ECMP, the load-balancing method at the multiple links for Catalyst 3750 is per IP packet or per destination IP?
Nexus 5500 support auto negotiation on 1gig sfp port? There is an end device that only support auto negotiation and cannot be manually set speed/duplex.
View 0 Replies View RelatedI just bought an Aironet 600 OfficeExtend AP and hooked it up to my WLC 5500 but I can't configure it.
I've got 10 AP running just fine but the Aironet 600 shows operational status as "UP" (normal is "REG") and "Admin status", "AP Mode" and "AP Sub Mode" are all grayed out.
I installed the newest firmware on the WLC (ver 7.2.110.0) and it has upgraded the Aironet 600 as well.
I've read to through the installation manuals and from everything I can see I should be able to configure the Aironet 600 as soon as it contact WLC
Any information on supervisor WS-X45-SUP7L-E? I saw that it has 520Gbps of backplane, but does it supports Netflow? How many uplink does it has?
View 6 Replies View RelatedCisco has put up the data sheet for the new 3850 switches. What do you all think about this new unified wired/wireless concept?
View 11 Replies View RelatedCan any ASA 5500 in particular the ASA5510 firewall support jumbo frames (i.e. greater than the default standard 1500 Bytes frames)?. I plan to use the ASAs to setup a point-to-point IPSec tunnel and need an Application frame of 4Kbytes intact and not segment it.I have done little checking on the Cisco Website and see it mention of Jumbo frames on the 5580 on 10Gig interface but didn't see mention 5510. 5580s are way over-kill and expensive for what I need is to run a mission critical one IPSec point-to-point with maximum of no more than 100Kbps so 5510 is perfect for me but not sure if it can carry the jumbo frame?
On the routers and switches it's the MTU settings and they are configurable per interface and I am OK and the circuit is T1 which the Telcos said it's OK since it's physical layer so the only unkown is the firewall.
can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedI want to upgrade the WLC 5500 from 7.0.220.0 to 7.3.112.0, coul be any risk if i do the upgrade..?
View 2 Replies View RelatedI have a Cisco 5500 Software Version 6.0.199.4. Today I've been able to succesfully add a few newly purchased 1242G APs to my WC so I know everything is setup properly. They got the proper DHCP info and I was up and running in a few minutes.
I'm now trying the same thing with a newly purchased Air-Lap1262N-a-KP
I can read the bootup because I'm attached to it on the console.I see that it gets the proper IP#
But then I keep getting a "failed to decode the discovery response" error.
[code]....
We have a WLC 5500 connected to a 2960 acting as core switch. there is a server attached to the switch , bearing all dhcp pools for lan and wireless users. Can the wlc or the switch be configured in such a way that the wireless users associating to the wlc get their ip addresses from the dhcp pool configured on the server. Can the configuration can be shared for such a setup.
View 5 Replies View Relatedi have a existing wireless network setup in my office existing wlc in 4402 and LAPs are 1130 & 1242 all are working fine but we are now planning to use new 5500 series controllers for the same access points,i want to ask that how i can done this job with very minore downtime and users disconnectivity + zero error results??
View 2 Replies View RelatedOur client have cisco 5500 Wireless lan controllers. They connect to core switch and other ports conenct to various switches on each floor. Then we have cisco AP 1300 series mounted on celing. I was reading that lightweight AP gets config from WLC as soon as they plug in. Need to know how the AP gets config from WLC switches?
View 8 Replies View RelatedI have quick question here does AP BR1310 can be associated with WLC 5500?
View 4 Replies View RelatedI have a Cisco aironet 3502i access point which I am using with a 5500 Wireless Controller. I was configuring the AP for flexconnect and accidentally enabled PPPoE authentication - but never set configured login details for PPPoE. Now when the AP boots up it tries to use PPPoE but fails - it never even looks for an IP address. I have no way to get the AP connected to the controller again.I tried logging into the AP via console, the AP gives me output but I never get a login, even when I hold down the Mode button during startup.I also tried holding the Mode button and waiting for the AP to boot with its default IP (10.0.0.1) and connecting to the AP via telnet, but I was unable to connect or even ping with my PC on the same network configured as 10.0.0.2.What can I do to set this AP back to defaults, to become a normal DHCP client, and reconnect to the wireless controller where I can reconfigure it?
View 9 Replies View RelatedI've recently installed ssl certificates for our web auth guest interface on our WLC's. I discoverd the they required a Level 2 certificae to work properly. We are getting an untrusted certicate on our 802.1x ssids that authenicate against a 5500 ASA..A certificate was insatlled and has an error, show the certificate as untrusted, my questionis, does the 5500 ASA require a level 2 certifate as well?
View 5 Replies View RelatedThe 5500 WLC would be the primary and 2500 WLC would be the secondary. The only need for the secondary would be in the event of failure of the primary, and support needs when doing maintenance such as code upgrades.
We would use the same version of code on each controller and apply the necessary amount of AP licenses on each. The controllers would have identical configurations and host multiple SSID's, including offering guest services. Does the 2500 support guest network services?
We have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
Can I configure a mobility groups between 2106 Wireless LAN Controller and 5500 Wireless LAN Controllers?
View 8 Replies View RelatedI'm using two 5500 WLCs with the version 7.2.110.0 When some AP with the part number AIR-CAP1552E-N-K9 associate with them, the 802.11g stays up and the 802.11a stays down.I saw the AP interfaces in Wireless --> All APs and the 802.11a is down and the regulatory domain show me not supported but the 802.11g is working normally.I follow this document from Cisco [URL] and i just have BR - Brazil to support this part number.
View 5 Replies View Relatedi have a 5500 series WLC connected to a switch through a trunk port with 2 v WLClans. the connection works fine, but sometimes it loses connectivity. it works again rebooting the wlc.
When the problem presented, i checked the cpd neighbors on switch and it didn't show the wlc, and i checked the cdp neighbors on WLC and this shows the switch in its neighbors list. i also checked the port counters on WLC and the receiver counters keep increasing, but the transmission counters remains in the same value. then i can see that only the TX side on the controller is down, if i restart the WLC the problem disappear temporarily.
Is there a misconfiguration or a wlc bug related to this behavior?
The switch is a Catalyst 3560
The WLC controller code is 6.0.188.0
Is it possible to use both LDAP (to Active Directory) authentication for a WLAN defined on a 5500 series controller, and use the local user account database (AAA) for the guest vlan?
View 1 Replies View RelatedActually we have a 4402 controller with 1120 APs both of which are marked as EoL products, we want to jump over the new 2600 APs and 5508 Controller for increase signal coverage but we have the following deals:Last firmware for 4402 controller is 7.0.Firmware needed for 5508 to support 2600 APs is 7.3.Is it possible to configure mobility between 4402 and 5508 even with different firmware branch?
View 3 Replies View RelatedI have created new ssid and i want to associate only one IP address with this SSID, so that only this user will be allowed to connect to AP. I have controller 5500 series.
View 6 Replies View RelatedI am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. All LWAPP which are up for more than 200-300 days has to be rebooted, this problem is with all AP's. clients are not getting connected,after reboot they work fine.how do the same from ncs.
View 5 Replies View RelatedIn the ISE documentation is states that under a Guest_Activity report you must have guest access logging enabled on the NAD in the ISE network. My question is where do I enable guest access logging in the WLC that is our NAD?
View 1 Replies View RelatedI have two 5500-controllers and one WCS-server. Now I will have to move the WCS-server to another subnet and change the IP, but it will keep the name.Will that effect the connection between the controllers and the WCS?Do I have the change anything in the configuration on the controllers or the WCS-server?
View 3 Replies View RelatedI get the following errors when a new 2600 series AP tries to join a 5500 series WLC:
*Apr 10 11:44:52.747: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 10 11:44:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.0.9 peer_port: 5246
[Code].....
10.0.0.9 is the management interface IP of the WLC. The primary-base is set manually due to the fact that we have several WLCs in place but only 1 is s 5500 series. The other ones are 4400 series WLCs. The new 2600 APs only can join a 5500 WLC afaik. The WLC runs 7.4.100.0