Cisco Wireless :: Will OfficeExtend 600 Work In Same Subnet Of WLC
May 16, 2013I know officeextend 600 is for home user. But i wanted to know is it possible for office extend 600 to work in same subnet/vlan of WLC.
View 5 Replies
ADVERTISEMENT
Cisco Wireless :: WiSM2 Version 7.4 Cannot Work On Same Subnet
Jan 8, 2013I have installed WiSM2 with ver 7.4 and Bonjour works great with instruction provided, But…… 2 problems. I cant get it to work on the same subnet. (odd since the whole problem was not able to work across subnets), More important the new Code function / password function on the airplay wont work. I get the code on the projector, but the ipad never pop up the login box it just errors out.
View 2 Replies View RelatedCisco Wireless :: OfficeExtend Support In 5500 WLC Datasheet
Sep 11, 2011Whats it "OfficeExtend support" in the 5500 WLC datasheet?.I dont see nothing about this in the WLC configuration guide release v7.0.116.0.Is this the same as OEAP?. Is the OfficeExtended (or OEAP) supported on the 1140 APs?. If so where can I get a guide to configure this?.
View 2 Replies View RelatedCisco Wireless :: OfficeExtend AP Not Join Controller WLC5508
Oct 4, 2010I try to configure an AP1131 as OfficeExtend but unfortunately I receive the following message from the debug command on the WLC5508: (Cisco Controller)
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Discovery Request from XX.XX.XX.XX:14847
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Join Priority Processing status =
[Code].....
Cisco :: Aironet 600 - Can't Configure OfficeExtend
Aug 7, 2012I just bought an Aironet 600 OfficeExtend AP and hooked it up to my WLC 5500 but I can't configure it.
I've got 10 AP running just fine but the Aironet 600 shows operational status as "UP" (normal is "REG") and "Admin status", "AP Mode" and "AP Sub Mode" are all grayed out.
I installed the newest firmware on the WLC (ver 7.2.110.0) and it has upgraded the Aironet 600 as well.
I've read to through the installation manuals and from everything I can see I should be able to configure the Aironet 600 as soon as it contact WLC
Adding A Subnet To A Switch On Different Subnet?
Aug 3, 2012What I am trying to do is I have one switch with say a 10.1.9.1 sub-net I need to have one of the ports to be trucked with two vlans one for DSL and the other for a local connection with the sub-net of 10.1.5.1 both of the sub-nets are configured in the core as 9 and 5 so I have port 0 set up as a trunk and it is set up as ge-0/0/0.0 vlan_5, vlan_192 on the 10.1.9.1 subnet switch. The DSL is working but the local is not pulling a 10.1.5.1 IP and has no connectivity. Everything looks as if it is configured correctly but still the DSl is working but not the Local connection.
View 2 Replies View RelatedLinksys Access Point :: To Work The Wireless Repeater Mode Work With WPA2-AES
Sep 6, 2011Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies View RelatedBest Subnet For Wireless Lan?
Jun 30, 2011Best subnet for wireless lan
View 1 Replies View RelatedCisco :: Routing Between Wireless And LAN Subnet
Oct 27, 2012I have a cisco 877w and ive setup two ssids on it each with different vlans (I intend to use the zone based firewall to lock down the guest zone later)
Ive made a quick diagram of my network its a single server with 2 NIC's one for the internal lan and another for the external network (direct connection to the router) The server hosts 3 virtualized servers with the ecternal nic only shared with the tmg 2010 server.
So my problem is that when I connect to the 10.0.1.1 network as 10.0.1.2 I can only ping the internal network however the internal network is incapable of responding (pinging back) giving destination host unreachable. I know I need some kind of routing but im not sure where to apply it on the TMG server with the next hop as 10.0.0.10 or on the router.
The guest wifi is intended to bypass the network firewall and not allow access to the internal network. I've enabled ip routing on the cisco router and attached the config below.
Cisco Wireless :: 1240AG - Two SSIDs With Same Subnet
Mar 18, 2013Is it possible to configure two SSIDs with same valn (default VLAN) with same IP addressing subnet on an autonomous 1240AG access point ios ver is 12.4 21a ja1.
View 3 Replies View RelatedCisco Wireless :: 4404 - Configuring WLC With Other VLan And Subnet
Sep 16, 2012I have currently Ciso4404 WLC installed which is in vlan4001 with the 172.16.10.0/24 subnet
I have bought Cisco 5508 WLC recently as AP count is increased... Can I install it in same vlan and subnet? If yes what would be the setting for APs to join... If no how can I configure it with other vlan and subnet..
Cisco Wireless :: Subnet Not Getting To The Internet With 1200 Series APs?
Dec 3, 2012I have a office network that was setup before I started. We have a 172. subnet and a 10.2 subnet. When users on Wifi get a 10.2 address ( ran out of 172 address ) they are not able to get out to the internet. But if the laptop is connected to a LAN port and get a 10.2 address they are able to get to the Internet. Not sure if its the Aps I need to configure or the Pix seeing that if they get a LAN address of 10.2 everything works. This is becoming a bigger issue now that the company has out grown its main subnet (172.)
APs= AIR-AP1231G-A-K9
Vlan = 172.16.1.XXX
Vlan2= 10.2.0.XXX
Hardware: PIX-515E, 64 MB RAM, CPU Pentium II 433 MHz
Wireless Router Does Not Accept Subnet Mask
Feb 27, 2013I am using TP-Link wireless router model no. TL-WR941ND.my isp provided static ip via cable modem.ip = a.b.c.d subnet = 255.255.255.254 = /31 but the router does not support subnet mask saying wrong subnet mask?
View 2 Replies View RelatedLinksys Wireless Router :: Can WRT120N Use Subnet 255.0.0.0
Mar 25, 2011I currently have a network using ipaddress 10.1.x.x and 10.2.x.x and 10.3.x.x with a subnet of 255.0.0.0 I purchased 2 of the wrt120n wireless routers for testing and find I can not use the subnet of 255.0.0.0.
View 9 Replies View RelatedWireless :: Subnet Mask Address Is Illegal Cisco Linksys?
Feb 23, 2011subnet mask address is illegal cisco linksys?
View 1 Replies View RelatedCisco Wireless :: AP1261N - Unable To Access Bvi Interface From Different Subnet
Apr 23, 2013I can't access the bvi interface I use to manage the AP1261N from an IP address that is not in the same subnet of the bvi interface. The AP is configured as root bridge. Obviously I've the same behaviour for the non-root AP connected to it. For sure it's an ap configuration problem as other devices in the same vlan (vlan1) are reachable by the vlan I'm connected to. This is the conf:
version 15.2
no service pad
service timestamps debug datetime msec
[Code].....
Cisco Wireless :: 4402 Adding New Subnet To Existing WLAN
Nov 23, 2012Moblie WLAN range 192.168.1.0/24.Default Gateway: 192.168.1.1 - Firewall..Next available range to add more addresses are 192.168.11.0/24..Current range is having IP address issues..I have seen a feature in 4402 controller that I can assigne second address range to exisgint SSID Mobile.What should I set the default gateway for 192.168.11.0/24 range?How can I point all mobile users traffic to the firewall as default gateway without creating additional interface on the firewall?I really do not want to create another vlan and interface in the network to just add another 255 addresses if tehre is any option?
View 3 Replies View RelatedCisco Wireless :: WLC 5508 / Cannot Create Interface As Same Vlan Id And Subnet
Aug 12, 2012I have got a wireless project with WLC main office and have 10 sites where ap's are there and ap's getting registerd .we need 4 ssid in all branches same .
ssid guest
ssid scanner
ssid user
vlan 600 main office for scanner 192.168.1.0
in branch
vlan 600 for scanner but ip is 172.16.1.0
and bgp is running . And customer is asking me not to edit the ip range or vlan or create new vlan . but in wlc am not able to create branch network 172.16.1.0 range interface and vlan 600 as vlan 600 i already created for scanner main office 192.168.1.0 So is there a way to do that .
Temprarly one site i did like created vlan 610 in branch no ip . And in main office interface vlan 610 given another ip range . and i created interface in wlc . from branch i can connect the ssid and getting ip . But they dont want to create any aditional vlan or another network . Customer dont have a smartnet contract . They recently baught 2 wlc 5508 and 40 ap 1142.
Cisco Wireless :: 4400 WLC / AP 1240 - Unable To Route Outside Of Own Subnet
Jul 14, 2008Cisco 4404 WLC
AP 1240 - LWAP
Wireless client receives a DHCP address from central DHCP server fine. Unable to route outside of own subnet . Continuous ARP WHO HAS (Default Gateway addr) TELL (client IP) messages being received. WLC running OS 4.2.99.0.
Home Network :: Wireless Access Point Need To Have Different Subnet
Oct 16, 2012it is each wireless access point need to have different subnet, if 24 users connect at the same time? will it be slow down if 24 user put in the same network?
View 1 Replies View RelatedLinksys Wireless Router :: How To Run Wired WRTG54G2 V1 In Same Subnet
Jan 1, 2013I have a linksys broadband router E2000 and a cable running from it to another location where I have a linksys WRTG2 V1. I would like the WRTG2 to be running in the same subnet as the E2000, but I seem not be able to get this done.
View 1 Replies View RelatedLinksys Wireless Router :: Subnet Mask 255.0.0.0 On WRT320N
Aug 22, 2011I'm using my WRT320N as a home router, I need more ipadresses to be delivered to my computers, yet I can't get my router to give med wider netmask range. In the list I get 255.255.255.0 - 255.255.255.240 or something like that. I need 255.0.0.0 on my network and that would be perfect if i could get that...
View 5 Replies View RelatedCisco Wireless :: 1142 - Aironet Configuration For Single Subnet Network
Feb 1, 2012We have recently aquired a remote location which has a pre-existing flat network (172.16.X.X/16). Before we are able to convert them over to our new IP scheme, they have a need to have wireless connectivity on site. We have 4 1142's which I need to configure for them. I have experience configuring WLC's and autonomous AP's for networks with multiple vlans but have never configured AP's for a flat, single subnet network. I need to configure them for either guest access (internet only) or corporate access to network resources with radius authentication. Do I configure a native vlan as I would for a typical multi vlan network? Do I configure the switch port as an access port as opposed to a trunk beacause of the lack of layer 3? I basically need a sample configuration for this situation.
View 1 Replies View RelatedCisco Wireless :: Inter Subnet Roaming With No Layer Device 3825
Mar 29, 2012The following picture is from a network in a hotel:
- Cisco 3825 is managed by AT&T. No access to this.
- There is no Layer 3 device in this network.
- Access Gateway at 100.1 operates at Layer 2. It receives tagged traffic in order to keep track of billings and user accounts so we can't add a Router in internal network. (Please verify)
- WLC's Management Interface lives in VLAN 100 at 100.2 with Default Gateway of 100.1
- Another WLC with Management Interface different VLAN than above, will be connected to the "Core Switch" to have Mobility.
- With Mobility Groups, IP connectivity must exist between the management interfaces of all controllers.
- Routing between VLANs need a Layer 3 device.
Any possible solutions to establish IP connectivity about the following:
- Changing Management Interface VLAN on one side and match it with the other side to eliminate Routing Requirements and having Inter-Controller Roaming instead of Inter-Subnet Roaming. (Reboot required?)
- Adding a NAT device between two WLCs and use Proxy ARP. (Haven't done this before, does this work?)
- Do you have better solution(s) in mind?
Cisco Wireless :: 871W Unable To Ping / Contact Another User On Same Subnet
Jul 28, 2012I have an 871 set up at home with 2 VLANs, both of these vlans present a strange behavior where an user is unable to ping/contact another user on the same subnet, however if users are on different subnet it seems to work [code]
According to the troubleshooting that I have done, the issue seems to be with the broadcast traffic, ARP request/reply do not reach another host on the same subnet (wireless to wireless or wired to wireless) however if the wireless device iniciates the connection to wired, it works fine.
I have tried to enable proxy arp on the different VLANs and BVI and different combinations but no sucess in order to get traffic across 2 wireless devices on the same subnet or a connection that is iniciated for a wired client to a wireless one.
I tried enabling and disabling dot11 arp-cache but no luck.
Linksys Wireless Router :: Routing PPPoE Subnet Using EA3500
Oct 4, 2012I was assigned a static block over PPPoE from the ISP. I can connect to the internet using the gateway address but I need to route the other static IPs to my servers. I might say that I accomplished it on a couple of older routers - E1200 & WRT120N, but I cannot get it to work on my new EA3500. I have 5 usable IPs plus the gateway IP that is assigned with the PPPoE connection on the WAN port.
View 8 Replies View RelatedLinksys Wireless Router :: E2500 Setting Internet Subnet To 255.255.0
Oct 29, 2011Due to the way I have my DSL and VOIP TA configured I need to be able to set the subnet mask in the Internet connection. I am currently using the Static IP, putting in an IP of 192.168.1.x with the subnet of 255.255.0.0 when I try to do this it gives me an error saying that 192.168.33.1/255 is reserved for the guest network. I am not using the 33 at all ANYWHERE. If I change the subnet to 255.255.255.0 it will save but I can't connect to the internet with it. My router I just bought today is the E2500 I have an old Linksys WRT model that worked fine with this exact setup for several years before it crashed on me.
View 3 Replies View RelatedLinksys Wireless Router :: E4200 And Sharing A Printer On Subnet?
Apr 2, 2012My issue is sharing a printer across my main Network and the wireless one, the description of the setting: I have my main Network 10.1.1.0/24 (RV082) and I hooked the wireless router E4200 at an IP 10.1.1.82 and the wireless network is 192.168.1.0/24 I setup a printer/scanner with an IP 192.168.1.72 for sharing on both Networks. Now everyone on 192.168.1.0 network is able to access and print but none on 10.1.1.0 I did put a static route on the RV082 to direct the requests for the printer to be redirected to 10.1.1.82 but no success.
The E4200 is setup by default out of the box I had just to set the static IP, Gateway and DNS and of course the wireless security key nothing else. the NAT is enabled on the E4200 and RIP is disabled, I tested the connection by disabling NAT and enabling RIP, at which I was able to connect to the printer but the Internet went down for All Wireless users (192.168.1.0 network)
Cisco Wireless :: 1142 Multicast Setup / One Subnet To Enable Apple Air-Play
May 3, 2012I’m having issues with enabling Apple’s AirPlay services on a relatively simple network consisting of a Cisco 881 (Advanced IP Services) and an autonomous Cisco 1142 AP. I’ve attached a diagram explaining the connectivity. I believe I have to enable IP Multicast at the router, but I’m not really sure the best/right way to do it. Also I’m not sure what/if any commands would be needed at the AP.All of the wireless clients are confirmed to be in the same subnet, so no real routing is happening etc. Also regular Internet connectivity/routing from the wireless clients is fine.
View 5 Replies View RelatedCisco Switching/Routing :: 3600 Accessing Wireless Access Point From Remote Subnet
Mar 28, 2013I recently installed a couple of Cisco Aironet 3600 Series Wireless Access Points at a remote site. While I was at the site everything seemed OK, The clients were able to get connected to the access points, the guest network worked fine, I could SSH into the access points, and I could ping them. The problem is when I went back to my home site I tried to SSH into the access points through an ASA IPSec VPN Tunnel and it couldn’t find it. When I try to ping the access points they “time out”. I can ping and connect all other addresses (via RDP, HTTP, etc..) on the same subnet which should rule out an access list problem. A couple of notes to be aware of:
The WAP’s have the Autonomous IOS installed (Version 15.2(2)JB) The WAP’s are connected to Dell PowerConnect 5724 (Not by choice.. We are a Cisco shop, these were already there and have plans this year to replace)
I can ping and SSH with Putty to the WAP’s from the local subnet I cannot ping or SSH from a remote subnet to the WAP’s. I can access all other IP’s and Computers from a remote subnet.
Linksys Wireless Router :: E2000 WAN IP Address Cannot Be Same Subnet As Guest Network IP Address
Jul 16, 2011I switched from Time Capsule with AirPort to E2000 and have a problem with configuration.I use the same IPs as in AirPort and E2000 gives me an error:"The WAN IP address cannot be the same subnet as the Guest Network IP address" and I can't save configuration.But in my opinion they are different.I use "Static IP" option and I have IPs from my ISP: [code] So WAN IP is different subnet as LAN and I don't know what to do now. It worked with these settings in AirPort and here I can't proceed.
View 2 Replies View RelatedHow To Subnet Within A Subnet
May 11, 2011i'm doing a project for my networking class and i need to know how to do subnetting within a subnet. it's a network with three routers, each of them being on their own subnet, but there are multiple departments for a store that each will have their own subnet (sales, management, warehouse, etc.) within the network subnet
View 5 Replies View RelatedCisco VPN :: ASA 5505 - SSL VPN To Lan Subnet
Oct 21, 2012I'm not sure if this is a possible config, but I have an ASA that I need to be able to SSL VPN to, and get an IP Address that is on the same subnet as my internal interface. The reason is, the person connecting in has a utility that does a broadcast on the internal network to discover the devices he is trying to connect to. Therefore, connecting over VPN and getting put on a different subnet wont work. In this case, I am going to start the ASA configuration from scratch. If its possible to do the above, what are the correct commands to configure it? I was planning to use 10.50.0.1/24 for the internal interface, and then hand out IP Addresses on that subnet to both the lan, and the vpn, This is an ASA 5505. Its on IOS 8.4.
View 1 Replies View Related
