Cisco Infrastructure :: Datasheet 4500 Doesn't Support Reflexive ACL
Jul 20, 2011
There is a vlan Finance in my office. The requrement : Vlan Finance is allow to access internet and selected host/network and not allow to access internal network. But from internal network can access to Vlan Finance (Full access). I want to configure using Reflexive ACL, but from Datasheet 4500 doesn't support Reflexive ACL. Intervlan routing is in 4500. Is there any ACL configuration to support my requirement without using Reflexive ACL?
View 1 Replies
ADVERTISEMENT
Sep 11, 2011
Whats it "OfficeExtend support" in the 5500 WLC datasheet?.I dont see nothing about this in the WLC configuration guide release v7.0.116.0.Is this the same as OEAP?. Is the OfficeExtended (or OEAP) supported on the 1140 APs?. If so where can I get a guide to configure this?.
View 2 Replies
View Related
May 21, 2006
I am trying to use deny mac acl in the 4500 series switch runnning cisco IOS but the command seems to be not working.
Here is the command,
mac access-list extended ABC
deny host 0001.8052.25FF any
int f4/11
mac access-group ABC in
Is there anything I am missing or is it a bug.
View 4 Replies
View Related
Feb 28, 2012
Does the 4500 support VSS (Virtual Switching System) ? On the official product overview page it says: 1.6 Terabits capacity with Virtual Switching System (hardware-ready)What means Hardware ready ? Does it mean that it supports VSS in the same manner as the 6500 ? The reason I'm asking this question is that I didn't find any info on the Internet about this. We would like to upgrade our network by interconnecting the 2 sites with Layer 2 redundant links (Layer 2 extension), but I'd like to use the both links in a load-balancing manner, which can be a real pain in the *** with STP. The choice is between 4500 and 3750 stackable core switches. The 6500s are very expensive.
View 6 Replies
View Related
May 9, 2013
We have ACS 5.3 with built in ACS View, does PI 1.3 support it? We have set up in PI 1.3 but unable to see the authentication records for clients, I wonder if they are compatible.
View 4 Replies
View Related
Apr 23, 2012
I am thinking about running some third-party unified communications apps under VMWare ESXi5 on a Cisco SRE 900 module. According to the Cisco docs, third-party apps are supported on these modules (see table below) but the app in question is NOT on Cisco's list below.
[URL]
Some questions:
1. As long as the third-party app is capable of running under VMWare/VSphere ESXi5, is there anything on the SRE that would prevent you from running this third-party app even though it's not on Cisco's list?
2. What is Cisco's policy on the use of third-party apps that are not on their list? For example, will they take a support call on the SRE running a non-listed app. (I don't want to void any sort of support contract through the use of a third-party app not on their list).
View 2 Replies
View Related
May 10, 2011
we have a Cisco 2851 router and bought the following IOS::
System image file is "flash:c2800nm-spservicesk9-mz.124-25d.bin"
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
I thought this version was supposed to have IPv6 support?
TEST(config)#ipv6 unicast-routing ^% Invalid input detected at '^' marker.
TEST(config)#
which IOS should we buy?
View 1 Replies
View Related
May 6, 2012
I am working on my CCENT after getting my A+. I have an old 3600 router and I am following CBT Nuggets to configure it. CBT Nuggets seems to have an IOS that supports VLAN and IP Addresses and it looks like mine only goes up to Token Ring so it doesn't mirror the instruction. I know it's an old router but is there a software release (like the 12.4 maybe?) that would allow me to follow the CBT Nuggets more accurately so that I can set the switch up for IP Addresses and VLAN instead of limiting me to token ring?
View 1 Replies
View Related
Apr 10, 2013
I do have a question, is WIC-1SHDSL-V3 able to support ADSL line?
We have WIC-1SHDSL-V3 module used for SDSL line, due to few site need to bring up with ADSL line with 1841 model, but HWIC-1ADSL module already EOS. The replacement model EHWIC-VA-DSL-A is not compatible to 1841. My architect suggest Symmetric Module like WIC-1SHDSL-V3 could be able to tweak the config to support Asymmetric purpose. I did google but do not found such related topic. Can any expert on this area to advice me?
View 1 Replies
View Related
Sep 5, 2011
Any information on supervisor WS-X45-SUP7L-E? I saw that it has 520Gbps of backplane, but does it supports Netflow? How many uplink does it has?
View 6 Replies
View Related
Jan 28, 2013
Cisco has put up the data sheet for the new 3850 switches. What do you all think about this new unified wired/wireless concept?
View 11 Replies
View Related
Oct 4, 2011
How to force the Cisco 1811 Router to read a Transcend CF 128MB? [code]
View 2 Replies
View Related
Jun 26, 2011
The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies
View Related
Mar 24, 2003
Currently it seems as our 3550's doesn't send traps when bpdu-guard sets a port in err-disable state. Or DFM doesnt recognize it.Is there a way to get a DFM alert when a 3550-port gets into err-disable state?
View 2 Replies
View Related
Apr 23, 2013
I'd like to configure ASDM access to ASA-SM using RSA SecurID authentication.I've followed instructions in this documen [URL]When I test access from CLI everything looks fine:
asa-vss/admin/act# test aaa-server authentication RSA
Server IP Address or name: xx.xx.xx.xx
Username: testuser
Password: **********
INFO: Attempting Authentication test to IP address <xx.xx.xx.xx> (timeout: 12 seconds)
INFO: Authentication Successful
[code]....
When I try to use ASDM, I'm unable to login and I can see lot of authentication error (Token reuse) messages on RSA server monitor window.It looks like ASDM 6.5(1) for ASA-SM doesn't support RSA/SDI authentication.
View 9 Replies
View Related
Jan 19, 2011
I have decided to buy a new wireless N enabled wireless router after my house was cleaned out by some robbers. After a long investigation I decided on the D-link DIR 655 as it suited my basic needs the best and since I haven't decided on a broadband supplier yet this should sort any and all possibilities no matter what I choose...
After an equal amount of investigation I decided on a HSPA+ USB dongle only to find that the router does not support the network I have purchased it on. It thenalso seems that it doesn't support the E1820 Huawei dongle either... so fine... I go and buy a Huawei D105 tht should technically be able to connect via the WAN port and would act as an internet gateway. Brilliant.
Now I have tried everything.... static IP on the D105 with a static IP setup on the 655. Connects fine... according to the web interface but NO INTERNET. When I connect my laptop directly to the 105 via CAT5 it works beautifully. DHCP on the D105 with the same on the 655. Connecting... Establishing Link (Please Wait...) FOREVER without ever getting an IP on the 655 (according to the web interface again) ... must be the D105 thats faulty so again plug in the laptop and within milliseconds the IP is assigned and Internet is blazing along again.... The D105 is not Wireless N so I cannot use it as my primary AP and only allows 5 simultaneous wireless connections (that is reserved for my cellphones). Why should I anyway?? the DIR655 should work fine....
Even after having taken it to D-link support at huge cost and effort I still don't have a working rig.... Seems the consultant plugged the D105 straight into the LAN on the 655 and then set his laptop to the same static range to get it to work... SURPRISE - I know that works since plugging the laptop straight into the 105 does the same thing.... But this is not what I want... I want my 655 to be the primary DHCP server for my network and control the allowed workstations that are allowed access to the internet with a working gateway. Bridging is apparently also not an option as that option has been removed so I cannot even bridge my main subnet onto the D105's internet sbnet... What am I to do....
If the 655 3G setup supported more than 2 dongles I might hve been able to use that and not spend anouther R600 on the D105, if the WAN port actually worked in either static or DHCP modes with the D105 that also would have solved the problem and lastly if all else fails and there was still bridging I could hack my own setup together to do what I want. Seems like I was wrong in selecting the D-link product.
Then to make matters worse I find another product with double the features online for half the price that integrates the 3G capability into the route and support more than 2 different models. including all the new Huawei dongles....
View 2 Replies
View Related
Jul 6, 2012
I've discovered that the DDNS update client in the RV042G does not support passwords that contains spaces. This is the first router I've run into that didn't like it.
View 1 Replies
View Related
Dec 13, 2011
We have 10 ADSL lines and 5 of them goes in the load balancer (One gateway) and the rests are used as default gateways for internet access. We use ADSL routers as access points for internet, but those routers should be part of our network and should be given an address in order for them to act as default gateways for internet access. I'm facing a real prob with the ADSL routers Linksys WAG54G2 because they doesn't support a subnet mask 255.255.0.0 Any recommendation for an ADSL router model that support a netmask 255.255.0.0 ?
My cisco 2811 router interface configuration ip address: 172.20.0.1 255.255.254.0.Load balancer output lan ip address: 172.20.0.5.My ADSL routers will be in the following range : 172.20.0.6 - 172.20.0.10
View 1 Replies
View Related
Apr 2, 2012
The client currently has DAS solution integrates with cisco ap1200 which has been eos. As per my knowledge DAS mobile access 2000 doesn't support. 802.11n, is this correct? We are planning to separate the dad environment with cisco. Basically positioning new 3600 n indoor AP to replace existing eos 1200. What are the pro and cons of separating two brands and solutions? Other cabling.The client having coverage issue and adding an amplifier and cable loss may add more issues to existing environment.
Also, based on experience 80211n AP are required is higher density vs 1200.What are your thoughts or best design option to separate das from WLAN environment?
View 6 Replies
View Related
May 2, 2011
If switches on a network doesn't support remote port mirroring and only local port mirroring, What are the options to still capture all the traffic from all switches on 1 single core switch?
View 1 Replies
View Related
Dec 31, 2012
Region : Finland
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 rel.577775n
ISP : saunalahti
dosen't support my huawei E392 4G modem. if possible would you make bin for this. there is not other modems that you can get for 4G connections from the service provider so it would be nice if there was more compatibility than some old ancient modems. starts to feel like this is been sold as 4G router and dosen't actually support that at all.
View 1 Replies
View Related
Jun 28, 2012
We have a customer that has a fiber rum between 2 building. They want to have 2 seperate fibers active that terminate into the same switch on each end. (redundancy).
In building A they have an extreme networks black diamond switch that does not support STP.In bulding B they have a Cisco 4507.
We will ahve to use a layer 3 routed connection due to the fact their switch in building A does not support STP.Our tech does not want to use static route becuase he does not want to setup IP SLA for the redundant connection.
Will RIPv2 work for this scenario and failover to the other fiber if needed? The hop count is the same for each fiber path..
View 2 Replies
View Related
Feb 16, 2011
can wireless router support up to 100 user including support network printer
View 1 Replies
View Related
Feb 20, 2013
Have a new 4500-x (Comes with IPBase enabled), but I see only universal image is available for download (Which I understand has "all" features)...assume it is safe to use the latest universal image on 4500-x and the IPBase license will be automatically applied?
I also see there is a new rom upgrade available - Is this the correct procedure to follow: [URL]
Should I be doing the rom upgrade first?
View 1 Replies
View Related
Sep 6, 2011
I have a 4510R+E switch that won't change to the SSO redundancy mode. After entering the 'mode SSO' command, the switch reboots the peer supervisor (as it says it will), but after it comes back up it remains in RPR mode. I've tried rebooting the peer supervisor manually, rebooting the entire chassis, manually power cycling the entire chassis, and reseating the sups, but the switch remains in RPR mode. The issue started when I swapped the switch's supervisor with the supervisor of another 4500. The same issue was observed on the other 4500 as well, but after several reboots, I got it to change to SSO mode. Prior to the swap, both switches were running in SSO mode just fine.Since we're running IOS version 15.0 with the 'spare sup' license, I suspect the issue arose because of licensing complications (with relation to the chassis serial number and the like) when I swapped the sups....although this doesn't explain why the other switch changed to SSO after some troubleshooting.
View 1 Replies
View Related
Oct 27, 2012
I do terminal monitor on my 4500 switch.I can't see the status of the interface ( when it become up or down)What is the problem? I need to add a command?
View 3 Replies
View Related
Dec 12, 2011
Im trying to locate the PDLM for the RTP audio for the 4500 series switch,
System image file is "boot flash:cat4500-entservices-mz.150-2.SG.bin"
Cisco WS-C4507R+E (MPC8245) processor (revision 7) with 524288K bytes of memory.
MPC8245 CPU at 333Mhz, Supervisor IV
Last reset from Power Up
8 Virtual Ethernet interfaces
48 Fast Ethernet interfaces
100 Gigabit Ethernet interfaces
403K bytes of non-volatile configuration memory.
It seems to be an easy task for routers:
[URL]
But not for these 4500's
[URL]
View 1 Replies
View Related
Oct 26, 2011
how to setup this old switch 4500. It is running CATOS and I want to make sure that when I connect it to the network it doesn't create a loop since it has to be compatible with other vendors, not just Cisco.I don't have anything connected but these are my concerns: It doesn't show my lacp-channel (i believe this is what is used to for Teaming network cards), it doesn't show my trunk ports.
TestSwitch> (enable) show lacp-channel
No ports channelling
TestSwitch> (enable) show trunk ?
detail Show detailed information
<mod> Module number
<mod/port> Module number and Port number(s)
[code]....
View 4 Replies
View Related
Jun 8, 2011
we got 2 Cisco 4005 Switches with IOS 12.x. t.Now we have two new Cisco 4500 Switches with Supervisor 6E-L.But i dont really understand the new syntax / configuration method of ios 15.
View 2 Replies
View Related
Jul 28, 2012
Im wanting to add an additional module in to my Cisco 4500. Is as simple as plug and play or is there some commands that I need to add or anything I should be aware of.
View 2 Replies
View Related
Dec 1, 2011
We inherited a lot of the equipment from another team of network administrators and every now and then, we run into a switch with some old code or configuration that was left behind and missed by us. Today, I discovered that CPP was enabled on 3 of our access-layer switches in one of the buildings we support.
View 3 Replies
View Related
Jan 17, 2013
We have a Cisco 4500 core switch and 2 Motorola AP 6532 access points. From the Motorola side the goal is to allow my corporate users access to network resources meanwhile offering my guest users only internet connectivity. My thought is to create two separate VLAN’s on my Cisco switch ex: vlan 10 (Business) 192.168.50.x and create another vlan 20 (guest) 192.168.2.x, also I made the proper configuration changes inside my Motorola AP device as well. From the Motorola I can ping myself but not my switch?
View 2 Replies
View Related
Mar 6, 2013
I need to know if Catalyst 4500-X does PBR in hardware?
View 1 Replies
View Related
