Region : Finland
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 rel.577775n
ISP : saunalahti
dosen't support my huawei E392 4G modem. if possible would you make bin for this. there is not other modems that you can get for 4G connections from the service provider so it would be nice if there was more compatibility than some old ancient modems. starts to feel like this is been sold as 4G router and dosen't actually support that at all.
I had my exisiting Huawei 3G Dongle replaced with a new LTE USB Dongle Huawei E392 from M1 Singapore. The router dectects it and I was able to get on to the Internet. But every after few mins, the connection will just hang and I have to go into the router to re-establish the connection.
Region : Others Model : TL-MR3020 Hardware Version : V1 Firmware Version : 3.14.2 Build 120817 Rel.55520n ISP : LMT
Recently got a new USB dongle - Huawei e392. Initially it worked fine, had no problems, but then suddenly it stopped connecting. I tried everything, forcing 3g, forcing 4g, re-upgrading firmware and uploading a .bin file, nothing works.
It just tries to connect, gets disconnected, and unplugs the USB modem, then does it over and over again.
Here's the log.
1st day 00:00:21 DHCP NOTICE DHCPS:Recv REQUEST from 00:25:22:CE:0D:73 1st day 00:00:23 DHCP NOTICE DHCPS:Send ACK to 192.168.1.100 1st day 00:00:27 DHCP NOTICE DHCPS:Recv INFORM from 00:25:22:CE:0D:73 1st day 00:01:10 3G/4G NOTICE handle_card start 1st day 00:01:10 3G/4G INFO LTE MODEM = 0, status = 1, targetVendorID = 0x0, targetProductID = 0x0 [Code] .......
Region : Others Model : TL-MR3220 Hardware Version : V2 Firmware Version : 3.14.4-121225-40357n ISP : PTCL
I have just bought TL-MR3220 router to use with Huawei EC315-2 USB 3G modem, but it is not being identified by the router. I checked compatibility list and it is not in 3G modem compatibility list. I tried to find out its bin file so that I can add modem configuration to the router but unfortunately could not find any.
Region : Sweden Model : TL-MR3220 Hardware Version : V1 Firmware Version : TL-MR3220_v2_120822 ISP : Telia, Sweden
I managed to get my Huawei E3131 from ISP Telia in Sweden to work for 4 days, from the detailed specification from my ISP I can see 1,9GB of data was sent/received with modem+router during those days. The router lost contact with the modem about 3 times during those 4 days but after a restart it was up and running again.
After those 4 days the router cannot find the modem anymore and even though I have upgraded the firmware it does not work. (I have tried both firmware versions available online without success).
I cannot find my Huawei modem in the compatibility list over "Other Location" compatible modems since Sweden is not even an option.
How is it possible that I managed to get it to work for a few days but after that not again? I have tried connecting the 3G-modem to the laptop and then it works perfectly.
Region : India Model : TL-MR3220 Hardware Version : V1 Firmware Version : 3.14.2 Build 120817 Rel.55520n ISP : Tata Photon Whiz
I just bought the TP Link MR 3020 and tried connecting my Tata Photon Whiz USB (Huawei EC121) modem with it. The TP Link cannot identify the modem. It goes forever into identifying mode. I next tried a Huawei E173 with Reliance 3g sim in it but again no results. The TP Link goes into identifying mode forever. I have installed the latest firmware for the device but am not able to set it up.
Region : UnitedKingdom Model : TL-MR3220 Hardware Version : V2 Firmware Version : 121126 Rel.70304n (BETA) ISP : T-mobile
there is a bug with MR3220 Router. I have HUAWEI E398 modem. It makes a LTE connections, everything works OK for half an hour, sometimes for a couple of hours, but then it (router)just unplugs modem after some time.ere is log:1st day 00:44:50DHCPNOTICEDHCPS:Recv DISCOVER from 8C:70:5A:8F:F0:E01st day 00:34:473G/4GNOTICEmodemUnplugedTime >=60s1st day 00:33:513G/4GINFO3G Modem is plugged out.1st day 00:33:493G/4GNOTICEdhcpcLteModemRelease 1261 sysCmd = ifconfig lte0 0.0.0.01st day 00:33:48DHCPINFOdhcpc_ipc_data_rcv_router 675 : current network type = 11st day 00:33:48DHCPNOTICEDHCPC Entering released state1st day 00:33:48DHCPNOTICEDHCPC Unicasting a release of 22.214.171.124 to 126.96.36.1991st day 00:33:473G/4GINFOprocess_msg 322 : call dhcpcLteModemRelease1st day 0:33:473G/4GINFOLTE MODEM = 0, status = 0, targetVendorID = 0x0, targetProductID = 0x0 1st day 00:33:473G/4GINFOLTE MODEM = 0, status = 1, targetVendorID = 0x0, argetProductID = 0x01st day 00:33:473G/4GNOTICEhandle_card start1st day 00:01:08DHCPWARNINGLTE Network connected.
Region : Italy Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : 3.14.2 Build 120822 Rel.57775n ISP : Vodafone Region : Italy Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : ISP : Vodafone
my MR 3220 cannot manage tp-link Ma180 modem. At start-up it tryes to identify the modem but after a while the status of the modem shows "Unplugged"
I already updated Router Firmware version. Firmware Version: 3.14.2 Build 120822 Rel.57775n Hardware Version: MR3220 v2 00000000 Signal strengts is weak but enough to access Internet when Ma180 is connect to my PC.
A piece of system log follows:
Index Time Type Level Log Content 9 1st day 00:17:00 3G/4G INFO LTE MODEM = 0, status = 3, targetVendorID = 0x0, targetProductID = 0x0
Region : UnitedKingdom Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : ISP :
I am connected to the internet via a non TP=Llink ADSL2 modem/router supplied by my ISP.I was using my TL-MR3220 as a 3G modem but no longer need it for that purpose. I was wondering whether I can now use my TL-MR3220 for two other purposes: as an additional wireless access point and as a means of linking equipment (i.e. printers) to the home network . i have tried connecting the ADSL2 modem/router to the TL-MR3220 via an ethernet cable (one of the 4 LAN ports on the ADSL modem/router to the blue WAN port on the TL-MR3220) but I can get no internet connection through the TL-MR3220.Is this normal i.e. something that the TL-MR3220 is not designed to do, or am I just using the wrong settings ? I have tried a whole range of different settings but none seem to work.
Region : Malaysia Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : 3.13.12 Build 120703 Rel.58323n ISP :
I'm using the TL-MR3220 hardware version 2.0. Firmware version 3.13.12 Build 120703 Rel.58323n. I'm using D-Link DWM-156 3.75G HSUPA USB Adapter.The problem I'm encountering is the router does not auto detect the 3G USB adapter when I power up the router. The router will detect the 3G adapter only when I plug out and plug in the 3G USB adapter. I used to have the same router but version 1.2. Version 1.2 does not have this problem.
Region : India Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : TL-MR3220_v_2_120822 ISP : MTS
My Hardware version is v2.Just now I bought this router. When I am trying to configure it with default firmware is not identifying the modem itself. So Afyter facing this problem, I updated my Router firmware(TL-MR3220_v_2_120822) and retry the process. But this time, It identified the modem for few seconds, then its changes its trying to connecting, after that its change it state to unplugged. It is doing these steps repeatably. Identifying >> Identified >> (connecting) >> Unplugged. [code]
Region : India Model : TL-MR3220 Hardware Version : V1 Firmware Version : TL-MR3220_V1_121123 ISP : Reliance Netconnect +
I have reliance ZTE AC2726 modem and i am trying to connect it with using the latest firmware version 121123. Router is able to detect the modem but when it tries to dial the connection is not established and reset the router after retrying 2-3 times. It was working perfectly fine earlier when i was on 120309 firmware version. So i tried downgrading my firmware version to 120309 and again it started working. I am not sure why the latest firmware version is not working with this device. Ideally the new firmware versions for a router should fix the existing issues and all the modems which were working earlier should work.
Region : India Model : TL-MR3220 Hardware Version : V2 Firmware Version : V2 ISP : Reliance netconnect Vendor (ZTE Model AC2736) CDM Region : India
Just now I bought this router. When I am trying to configure it with default firmware is not identifying the modem itself. So Afyter facing this problem, I updated my Router firmware(TL-MR3220_v_2_120822) and retry the process. But this time, It identified the modem for few seconds, then its changes its trying to connecting, after that its change it state to unplugged.
Region : Argentina Model : TL-MR3220 Hardware Version : V2 Firmware Version : ISP : Region : Others Model : TL-MR3220 Hardware Version : V1 Firmware Version : latest ISP : Orange
The TL-MR3220 takes a long time to identify the 3g modem and sometimes it will not identify it at all and says "unplugged". Sometimes "unplugged" suddenly apears after the modem has been identified and was working properly.Is this the normal behavior of this device ? Why ? What can be done ? I'm Using Alcatel X500D 3g modem.
Region : Italy Model : TL-MR3220 Hardware Version : V1 Firmware Version : 120822 ISP : TIM
I have a compatibility problem with the 3G USB Modem ONDA MT191UP with 3220 V2 updated with the firmware 120822 uploaded on TPLINK web site . Every thing is ok , the wireless is created , but the internet connection is missing . The router does not show the USB led , and it remain always in "connecting" but nothing happen . Do you have some infor to be compatible this USB modem ( some firmware , some Bin file etc..) ?I checked the Huawei E1800 and it works perfectly.
Region : India Model : TL-MR3220 Hardware Version : V2 Firmware Version : 3.14.2 Build 120822 Rel.57775n ISP : BSNL
I am unable to connect my TP-Link TL-MR3220 router with BSNL EVDO ZTE AC8700 modem. Even though my router has the latest firmware version 3.14.2 Build 120822 Rel.57775n, which is the boxed firmware i got with my router. All the time my modem gets Identified by the router, then it shows connecting phase......and restarts the modem.........Repeats the same step every time I try to connect.
I have decided to buy a new wireless N enabled wireless router after my house was cleaned out by some robbers. After a long investigation I decided on the D-link DIR 655 as it suited my basic needs the best and since I haven't decided on a broadband supplier yet this should sort any and all possibilities no matter what I choose...
After an equal amount of investigation I decided on a HSPA+ USB dongle only to find that the router does not support the network I have purchased it on. It thenalso seems that it doesn't support the E1820 Huawei dongle either... so fine... I go and buy a Huawei D105 tht should technically be able to connect via the WAN port and would act as an internet gateway. Brilliant.
Now I have tried everything.... static IP on the D105 with a static IP setup on the 655. Connects fine... according to the web interface but NO INTERNET. When I connect my laptop directly to the 105 via CAT5 it works beautifully. DHCP on the D105 with the same on the 655. Connecting... Establishing Link (Please Wait...) FOREVER without ever getting an IP on the 655 (according to the web interface again) ... must be the D105 thats faulty so again plug in the laptop and within milliseconds the IP is assigned and Internet is blazing along again.... The D105 is not Wireless N so I cannot use it as my primary AP and only allows 5 simultaneous wireless connections (that is reserved for my cellphones). Why should I anyway?? the DIR655 should work fine....
Even after having taken it to D-link support at huge cost and effort I still don't have a working rig.... Seems the consultant plugged the D105 straight into the LAN on the 655 and then set his laptop to the same static range to get it to work... SURPRISE - I know that works since plugging the laptop straight into the 105 does the same thing.... But this is not what I want... I want my 655 to be the primary DHCP server for my network and control the allowed workstations that are allowed access to the internet with a working gateway. Bridging is apparently also not an option as that option has been removed so I cannot even bridge my main subnet onto the D105's internet sbnet... What am I to do....
If the 655 3G setup supported more than 2 dongles I might hve been able to use that and not spend anouther R600 on the D105, if the WAN port actually worked in either static or DHCP modes with the D105 that also would have solved the problem and lastly if all else fails and there was still bridging I could hack my own setup together to do what I want. Seems like I was wrong in selecting the D-link product.
Then to make matters worse I find another product with double the features online for half the price that integrates the 3G capability into the route and support more than 2 different models. including all the new Huawei dongles....
Region : Portugal Model : TL-MR3040 Hardware Version : V1 Firmware Version : TL-MR3040_V1_120822 ISP : Optimus Kanguru (LTE) www.kanguru.pt
I have a modem huawei E392u-12 from the service provider optimus kanguru, url..., and i would like to use my usb modem with this router i have. the router identify the modem but does not conect. i have seen that the bin files available are just for vodafone and TMN, what can i do so i dont have to buy another equipment.
Region : Others Model : TL-MR3040 Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
I have a Huawei 523a Router at the moment and I'm trying to setup a IP camera.The Router doesnt allow port forwarding, so my question is can I add another Router onto the Huawei router to allow the second one to work my camera
Region : UnitedKingdom Model : TL-MR3220 Hardware Version : Not Clear
im currently on three netowork usb dongle e3231 and wanting to setup a WiFi network using this dongle would the mr 3220 be a suitable router for my three dongle? also on the tp link site it says the router is battery operated is this the case as im sure it loooks like theres an adaptor plug on the back.
Region : Singapore Model : TL-MR3220 Hardware Version : V1 Firmware Version :
I travel and connect this device in the hotels. On this occasion, the hotel wired connection is limited to one device with username/password entered through the web page. Is there a way to share this connection using one of the modes to multiple devices (the devices will run in a different subnet than the hotel network). I understand I can do this in WISP mode but only for sharing hotel wireless connection. The hotel wifi has poor reception, hence I want to use wired. Is there a way to do this? I would imagine this would be not an unusual scenario in many top hotels. Mid hotels generally do not have such limitations.