TP-Link 3G/3.75G Router :: Unable To Connect MR3220 With BSNL EVDO ZTE AC8700 Modem
Feb 13, 2013
Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : BSNL
I am unable to connect my TP-Link TL-MR3220 router with BSNL EVDO ZTE AC8700 modem. Even though my router has the latest firmware version 3.14.2 Build 120822 Rel.57775n, which is the boxed firmware i got with my router. All the time my modem gets Identified by the router, then it shows connecting phase......and restarts the modem.........Repeats the same step every time I try to connect.
Region : India Model : TL-MR3020 Hardware Version : V1 Firmware Version : ISP : BSNL
I'm unable to configure my Data Card (ZTE-AC8700). I tried with manual settings but it keeps on showing the message "connecting" but doesn't connects although my datacard is shown as identified by the device MR-3020. I'm using BSNL EVDO connection and my datacard is ZTE-AC8700. It doesn't uses any APN, only a username and password and dial number "#777" is required to connect. configuring my datacard with MR3020 ???
Region : India Model : TL-MR3220 Hardware Version : V2 Firmware Version : 3.14.2 Build 120822 Rel.57775n ISP : BSNL EVDO
my BSNL evdo ZTE AC8700 modem is not working with TL-MR3220 V2. The modem is being detected in the router and i have set the Dialing number, username, password. [code]
Region : India Model : TL-MR3220 Hardware Version : V2 Firmware Version : 3.15.2 Build 130326 Rel.56282n ISP : BSNL EVDO
I have tested two zte ac 8700 bsnl evdo modems with tp link mr3220.its not working with the tp link mr 3220.it is lited as the compatible modem in the website. I have updated the firmware.
Region : India Model : TL-MR3420 Hardware Version : V2 Firmware Version : Problem persists on all three firmware ISP : BSNL india on EVDO
Today i purchased brand new Tp-Link MR-3420 3G/4G router for my BSNL EVDO modem..as this product is shown to support ZTE AC8700 modem...but it doesnt seem to work.. I put the right dial-up number,user name and password that i use when i connect modem to laptop and left APN field blank...The modem gets identified by the router but it just don't connect to internet,it just keeps saying "connecting.....". Also the signal strength is shown 0%... If your modem is really supporting ZTE AC8700 modem why its not working?
Region : India Model : TL-MR3220 Hardware Version : V2 Firmware Version : ISP : tata photon plus
I have Tp-link 3g/3.75 wireless lite n Router model number TL-Mr3220 . I have just bought Tata Photon plus device huawei ec156. I am not able to connetct to the usb dongle . How to connect to the USB dongle. Following the ast setup guide . Its saying Unknown PIN status, please insure that your SIM/UIM is on unlock status.
I want to connect my tata photon device to my bsnl wifi modem via a usb portavailable on the bsnl modem. This is to provide a wifi network that i can use to surf the net on my phone.
Region : India Model : TL-MR3220 Hardware Version : V1 Firmware Version : 3.14.2 Build 120817 Rel.55520n ISP : Tata Photon Whiz
I just bought the TP Link MR 3020 and tried connecting my Tata Photon Whiz USB (Huawei EC121) modem with it. The TP Link cannot identify the modem. It goes forever into identifying mode. I next tried a Huawei E173 with Reliance 3g sim in it but again no results. The TP Link goes into identifying mode forever. I have installed the latest firmware for the device but am not able to set it up.
Region : UnitedKingdom Model : TL-MR3220 Hardware Version : V2 Firmware Version : 121126 Rel.70304n (BETA) ISP : T-mobile
there is a bug with MR3220 Router. I have HUAWEI E398 modem. It makes a LTE connections, everything works OK for half an hour, sometimes for a couple of hours, but then it (router)just unplugs modem after some time.ere is log:1st day 00:44:50DHCPNOTICEDHCPS:Recv DISCOVER from 8C:70:5A:8F:F0:E01st day 00:34:473G/4GNOTICEmodemUnplugedTime >=60s1st day 00:33:513G/4GINFO3G Modem is plugged out.1st day 00:33:493G/4GNOTICEdhcpcLteModemRelease 1261 sysCmd = ifconfig lte0 0.0.0.01st day 00:33:48DHCPINFOdhcpc_ipc_data_rcv_router 675 : current network type = 11st day 00:33:48DHCPNOTICEDHCPC Entering released state1st day 00:33:48DHCPNOTICEDHCPC Unicasting a release of 178.160.9.196 to 178.160.9.1931st day 00:33:473G/4GINFOprocess_msg 322 : call dhcpcLteModemRelease1st day 0:33:473G/4GINFOLTE MODEM = 0, status = 0, targetVendorID = 0x0, targetProductID = 0x0 1st day 00:33:473G/4GINFOLTE MODEM = 0, status = 1, targetVendorID = 0x0, argetProductID = 0x01st day 00:33:473G/4GNOTICEhandle_card start1st day 00:01:08DHCPWARNINGLTE Network connected.
Region : Italy Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : 3.14.2 Build 120822 Rel.57775n ISP : Vodafone Region : Italy Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : ISP : Vodafone
my MR 3220 cannot manage tp-link Ma180 modem. At start-up it tryes to identify the modem but after a while the status of the modem shows "Unplugged"
I already updated Router Firmware version. Firmware Version: 3.14.2 Build 120822 Rel.57775n Hardware Version: MR3220 v2 00000000 Signal strengts is weak but enough to access Internet when Ma180 is connect to my PC.
A piece of system log follows:
Index Time Type Level Log Content 9 1st day 00:17:00 3G/4G INFO LTE MODEM = 0, status = 3, targetVendorID = 0x0, targetProductID = 0x0
Region : UnitedKingdom Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : ISP :
I am connected to the internet via a non TP=Llink ADSL2 modem/router supplied by my ISP.I was using my TL-MR3220 as a 3G modem but no longer need it for that purpose. I was wondering whether I can now use my TL-MR3220 for two other purposes: as an additional wireless access point and as a means of linking equipment (i.e. printers) to the home network . i have tried connecting the ADSL2 modem/router to the TL-MR3220 via an ethernet cable (one of the 4 LAN ports on the ADSL modem/router to the blue WAN port on the TL-MR3220) but I can get no internet connection through the TL-MR3220.Is this normal i.e. something that the TL-MR3220 is not designed to do, or am I just using the wrong settings ? I have tried a whole range of different settings but none seem to work.
Region : Malaysia Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : 3.13.12 Build 120703 Rel.58323n ISP :
I'm using the TL-MR3220 hardware version 2.0. Firmware version 3.13.12 Build 120703 Rel.58323n. I'm using D-Link DWM-156 3.75G HSUPA USB Adapter.The problem I'm encountering is the router does not auto detect the 3G USB adapter when I power up the router. The router will detect the 3G adapter only when I plug out and plug in the 3G USB adapter. I used to have the same router but version 1.2. Version 1.2 does not have this problem.
Region : Finland Model : TL-MR3220 Hardware Version : V2 Firmware Version : Newest ISP : Sonera
I have a TP-Link TL-MR3220 and Huawei E3276 USB-modem (Sonera, Finland)Is there some update or advices, that can i use this huawei with MR3220? Or when update releases?
Region : India Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : TL-MR3220_v_2_120822 ISP : MTS
My Hardware version is v2.Just now I bought this router. When I am trying to configure it with default firmware is not identifying the modem itself. So Afyter facing this problem, I updated my Router firmware(TL-MR3220_v_2_120822) and retry the process. But this time, It identified the modem for few seconds, then its changes its trying to connecting, after that its change it state to unplugged. It is doing these steps repeatably. Identifying >> Identified >> (connecting) >> Unplugged. [code]
Region : India Model : TL-MR3220 Hardware Version : V1 Firmware Version : TL-MR3220_V1_121123 ISP : Reliance Netconnect +
I have reliance ZTE AC2726 modem and i am trying to connect it with using the latest firmware version 121123. Router is able to detect the modem but when it tries to dial the connection is not established and reset the router after retrying 2-3 times. It was working perfectly fine earlier when i was on 120309 firmware version. So i tried downgrading my firmware version to 120309 and again it started working. I am not sure why the latest firmware version is not working with this device. Ideally the new firmware versions for a router should fix the existing issues and all the modems which were working earlier should work.
Region : India Model : TL-MR3220 Hardware Version : V2 Firmware Version : V2 ISP : Reliance netconnect Vendor (ZTE Model AC2736) CDM Region : India
Just now I bought this router. When I am trying to configure it with default firmware is not identifying the modem itself. So Afyter facing this problem, I updated my Router firmware(TL-MR3220_v_2_120822) and retry the process. But this time, It identified the modem for few seconds, then its changes its trying to connecting, after that its change it state to unplugged.
Region : UnitedKingdom Model : TL-MR3220 Hardware Version : V1 Firmware Version : ISP :
I will soon be moving to somewhere without DSL service. I was wondering if it is possible to connect my iphone 4 to the usb of the mr3220 and use the iphone's 3g data allowence?
Region : Argentina Model : TL-MR3220 Hardware Version : V2 Firmware Version : ISP : Region : Others Model : TL-MR3220 Hardware Version : V1 Firmware Version : latest ISP : Orange
The TL-MR3220 takes a long time to identify the 3g modem and sometimes it will not identify it at all and says "unplugged". Sometimes "unplugged" suddenly apears after the modem has been identified and was working properly.Is this the normal behavior of this device ? Why ? What can be done ? I'm Using Alcatel X500D 3g modem.
Region : Finland Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : 3.14.2 Build 120822 rel.577775n ISP : saunalahti
dosen't support my huawei E392 4G modem. if possible would you make bin for this. there is not other modems that you can get for 4G connections from the service provider so it would be nice if there was more compatibility than some old ancient modems. starts to feel like this is been sold as 4G router and dosen't actually support that at all.
Region : Italy Model : TL-MR3220 Hardware Version : V1 Firmware Version : 120822 ISP : TIM
I have a compatibility problem with the 3G USB Modem ONDA MT191UP with 3220 V2 updated with the firmware 120822 uploaded on TPLINK web site . Every thing is ok , the wireless is created , but the internet connection is missing . The router does not show the USB led , and it remain always in "connecting" but nothing happen . Do you have some infor to be compatible this USB modem ( some firmware , some Bin file etc..) ?I checked the Huawei E1800 and it works perfectly.
My laptop's wifi is just working fine with TP Link but I'm unable to connect internet via wifi on my iPhone 3G. My iPhone's wifi just works fine in my office. Is there any solution available?
Region : Hongkong Model : TL-MR3220 Hardware Version : V1 Firmware Version : 3.14.2 Build 120822 Rel.57775n ISP : 123
In order to use public IP provided by the ISP, I have to enter the specific APN.It's however no matter what I type in the field of the APN, the router is still connected to the default APN settings from ISP.I have tried typed wrong string in the field of APN, the router is still connected to the default APN successfully.
Region : UnitedStates Model : TL-MR3220 Hardware Version : V1 Firmware Version : 3,14.2 build 120822 rel.40902n ISP : Sprint
Been working on this for about a week now, still no success. I confirmed I am using the latest update version/build.Trying to connect to my Ipad. TPLink Software says Identified, but only goes toward "Connecting" and never connects.All the ISP/Subnet numbers are "0". Set to 3g/4g only setting. Tried with security password and with security disabled.Customer support asked me to call Sprint to confirm dial number is #777 and that is confirmed. Sprint also confirmed APN is not needed to connect to a wireless router using a USB modem (this is a U600, which is on the TPLink compatable list). There is some internet posting that says the APN for Sprint is internet.com but I tried this too, and it still wont connect.
I have 2 computers and 1 printer connected to the dsl modem and another computer and 2 printers connected to a router, I have internet connection to all. the problem I am having is I am trying to add 2 of the printers that are on the router to my pc's but I am unable to locate them also I am unable to log into my router through one of the computers that is connected to my modem directly but I can connect to my router with the pc connected directly to the router.
All the printers are set to share. Is the only way to do this is to connect all the printers to the main PC and then network all the pc's together? I am just trying to connect to all the printers that are on modem and router from any of the pc's connected to modem and router.
Region : Argentina Model : TL-MR3220 Hardware Version : V2 Firmware Version : Region : Others
I have MR3220 version 2 and HUAWEI E398 stick.It connects to 3G/4G network, but with wrong APN.It seems to me that manualy changed APN can not be applied. [code]
Region : Italy Model : TL-MR3220 Hardware Version : V1 Firmware Version : 3.12.20 Build 120705 Rel.39030n Beta ISP :
I'm facing problem to properly set BRIDGE mode (WDS Bridging). I had a router connected to ADSL line with following setting:
IP 192.168.1.1 Security setting - WPA2/TKIP DHCP on
The wi-fi coverage is not good in all the floor so I'm trying to extend coverage using a TL-MR3220. I did follow the instruction in this video [url]....
Region : UnitedKingdom Model : TL-MR3220 Hardware Version : Not Clear
im currently on three netowork usb dongle e3231 and wanting to setup a WiFi network using this dongle would the mr 3220 be a suitable router for my three dongle? also on the tp link site it says the router is battery operated is this the case as im sure it loooks like theres an adaptor plug on the back.
Region : Finland Model : TL-MR3220 Hardware Version : V1 Firmware Version : TL-MR3220_V1_120523 ISP : DNA
Would it be possible to get huawei e3131 working with other ISP than Poland model? Since it seams to be technically just the same 3g modem, but ISP play locked bin file for it.
