Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.15.2 Build 130326 Rel.56282n
ISP : BSNL EVDO
I have tested two zte ac 8700 bsnl evdo modems with tp link mr3220.its not working with the tp link mr 3220.it is lited as the compatible modem in the website. I have updated the firmware.
Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : BSNL
I am unable to connect my TP-Link TL-MR3220 router with BSNL EVDO ZTE AC8700 modem. Even though my router has the latest firmware version 3.14.2 Build 120822 Rel.57775n, which is the boxed firmware i got with my router. All the time my modem gets Identified by the router, then it shows connecting phase......and restarts the modem.........Repeats the same step every time I try to connect.
Region : India
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : BSNL EVDO
I have one BSNL EVDO data card which was working fine before firmware upgrade to latest 3.14.2 Build 120822 Rel.57775n. Now it is keep on saying device unplugged after identifying the device. The device is working fine while connected on my laptop.
Region : Others
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.14.4-121225-40357n
ISP : PTCL
I have just bought TL-MR3220 router to use with Huawei EC315-2 USB 3G modem, but it is not being identified by the router. I checked compatibility list and it is not in 3G modem compatibility list. I tried to find out its bin file so that I can add modem configuration to the router but unfortunately could not find any.
Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : BSNL EVDO
my BSNL evdo ZTE AC8700 modem is not working with TL-MR3220 V2. The modem is being detected in the router and i have set the Dialing number, username, password. [code]
Region : Poland
Model : TL-MR3220
Hardware Version : V1
Firmware Version :
ISP : Bite
Router TL-MR3220 works well on 3G network, but is not works 2G (edge) network. 3G network is not suported in my location, only 2G. My modem is Huawei E 173. In location 2G network Router show: 3G/4G USB Modem: Unplugged.
Region : India
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : TL-MR3220_v_2_120822
ISP : MTS
My Hardware version is v2.Just now I bought this router. When I am trying to configure it with default firmware is not identifying the modem itself. So Afyter facing this problem, I updated my Router firmware(TL-MR3220_v_2_120822) and retry the process. But this time, It identified the modem for few seconds, then its changes its trying to connecting, after that its change it state to unplugged. It is doing these steps repeatably. Identifying >> Identified >> (connecting) >> Unplugged. [code]
Region : Portugal
Model : TL-MR3220
Hardware Version : V2
Firmware Version : TL-MR3220_V2_121126_UK
ISP : OPTIMUS (26803)
I buy a Router TL-MR3220 and Forwarding e Dynamic DNS not work. I installed the latest firmware version (TL-MR3220_V2_121126_UK) and does not work well.
Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : TL-MR3220_v2_120822
ISP : MTS and BSNL
Both modems (ZTE AC2746 and Prithvi UE100) are on the compatible list. Though they updated the compatible list with 'Prithvi UE100 (ISP: BSNL)' to be compatible with only v1 for unknown reasons, which led me to buy ZTE AC2746 (ISP: MTS) and now, it's not working either .Prithvi UE100: The modem connects to the internet but after about 3 minutes it disconnects. "Disconnect > Unplugged >Identifying> Identified >Connecting> Connected > Disconnected" and it keeps repeating.ZTE AC2746: The modem gets identified but after showing 'Connecting' it shows 'Unplugged' without even connecting to internet. This modem is on TP-MR3220 v2 compatible list.
I am having BSNL broadband & netgear router. Some of the sites are not opening like [URL] many more?
View 4 Replies View RelatedRegion : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP : BSNL
I'm unable to configure my Data Card (ZTE-AC8700). I tried with manual settings but it keeps on showing the message "connecting" but doesn't connects although my datacard is shown as identified by the device MR-3020. I'm using BSNL EVDO connection and my datacard is ZTE-AC8700. It doesn't uses any APN, only a username and password and dial number "#777" is required to connect. configuring my datacard with MR3020 ???
Region : Brazil
Model : TL-MR3020
Hardware Version : V1
Firmware Version : V1.00 120817
ISP : CLARO (Brazil)
I have three 3G Routers TP-Link TL-MR3020 120 817 V1.00, a modem 3G Huawei E303C and another 3G modem ZTE MF-190 with ship operator CLARO (BRAZIL). I can not get 3G Router 3G modems work with these, although it is loaded with the latest firmware.
Region : Australia
Model : TL-MR3420
Hardware Version : V2
ISP : Optus, Telstra
Whilst the MR3420 V2 is sold as a 4G usb router, it appears that it does not support many usb 4G devices.In Australia we currently have the Seirra 320u, ZTE MF821 (100Mbps Cat 3) and Huawei E3276 (150Mbps Cat 4)whilst the V2 supports the first two (not the E3276), it has one major failure!It does not work at full 4G speeds.
The V2 does not appear to allow download speeds in excess of 25Mbps or uploads much greater than 2Mbps. This occurs on fast 3G and 4G networks.The throttled speed is apparently due to slow modem protocols deployed in the router. High protocol overheads mean it cannot 'shuffle data' very fast.We have developed working solutions using the Openwork platform that overcome these issues and provides speeds in excess of 70mbps.
Region : India
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : Tata Photon Whiz
I just bought the TP Link MR 3020 and tried connecting my Tata Photon Whiz USB (Huawei EC121) modem with it. The TP Link cannot identify the modem. It goes forever into identifying mode. I next tried a Huawei E173 with Reliance 3g sim in it but again no results. The TP Link goes into identifying mode forever. I have installed the latest firmware for the device but am not able to set it up.
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
Region : Others
I have MR3220 version 2 and HUAWEI E398 stick.It connects to 3G/4G network, but with wrong APN.It seems to me that manualy changed APN can not be applied. [code]
Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 121126 Rel.70304n (BETA)
ISP : T-mobile
there is a bug with MR3220 Router. I have HUAWEI E398 modem. It makes a LTE connections, everything works OK for half an hour, sometimes for a couple of hours, but then it (router)just unplugs modem after some time.ere is log:1st day 00:44:50DHCPNOTICEDHCPS:Recv DISCOVER from 8C:70:5A:8F:F0:E01st day 00:34:473G/4GNOTICEmodemUnplugedTime >=60s1st day 00:33:513G/4GINFO3G Modem is plugged out.1st day 00:33:493G/4GNOTICEdhcpcLteModemRelease 1261 sysCmd = ifconfig lte0 0.0.0.01st day 00:33:48DHCPINFOdhcpc_ipc_data_rcv_router 675 : current network type = 11st day 00:33:48DHCPNOTICEDHCPC Entering released state1st day 00:33:48DHCPNOTICEDHCPC Unicasting a release of 178.160.9.196 to 178.160.9.1931st day 00:33:473G/4GINFOprocess_msg 322 : call dhcpcLteModemRelease1st day 0:33:473G/4GINFOLTE MODEM = 0, status = 0, targetVendorID = 0x0, targetProductID = 0x0
1st day 00:33:473G/4GINFOLTE MODEM = 0, status = 1, targetVendorID = 0x0, argetProductID = 0x01st day 00:33:473G/4GNOTICEhandle_card start1st day 00:01:08DHCPWARNINGLTE Network connected.
Region : Italy
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.20 Build 120705 Rel.39030n Beta
ISP :
I'm facing problem to properly set BRIDGE mode (WDS Bridging). I had a router connected to ADSL line with following setting:
IP 192.168.1.1
Security setting - WPA2/TKIP
DHCP on
The wi-fi coverage is not good in all the floor so I'm trying to extend coverage using a TL-MR3220. I did follow the instruction in this video [url]....
Region : Italy
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : Vodafone
Region : Italy
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP : Vodafone
my MR 3220 cannot manage tp-link Ma180 modem. At start-up it tryes to identify the modem but after a while the status of the modem shows "Unplugged"
I already updated Router Firmware version. Firmware Version: 3.14.2 Build 120822 Rel.57775n Hardware Version: MR3220 v2 00000000 Signal strengts is weak but enough to access Internet when Ma180 is connect to my PC.
A piece of system log follows:
Index Time Type Level Log Content
9 1st day 00:17:00 3G/4G INFO LTE MODEM = 0, status = 3, targetVendorID = 0x0, targetProductID = 0x0
[Code].....
Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : Not Clear
im currently on three netowork usb dongle e3231 and wanting to setup a WiFi network using this dongle would the mr 3220 be a suitable router for my three dongle? also on the tp link site it says the router is battery operated is this the case as im sure it loooks like theres an adaptor plug on the back.
Region : Finland
Model : TL-MR3220
Hardware Version : V1
Firmware Version : TL-MR3220_V1_120523
ISP : DNA
Would it be possible to get huawei e3131 working with other ISP than Poland model? Since it seams to be technically just the same 3g modem, but ISP play locked bin file for it.
Region : Singapore
Model : TL-MR3220
Hardware Version : V1
Firmware Version :
I travel and connect this device in the hotels. On this occasion, the hotel wired connection is limited to one device with username/password entered through the web page. Is there a way to share this connection using one of the modes to multiple devices (the devices will run in a different subnet than the hotel network). I understand I can do this in WISP mode but only for sharing hotel wireless connection. The hotel wifi has poor reception, hence I want to use wired. Is there a way to do this? I would imagine this would be not an unusual scenario in many top hotels. Mid hotels generally do not have such limitations.
Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP :
I am connected to the internet via a non TP=Llink ADSL2 modem/router supplied by my ISP.I was using my TL-MR3220 as a 3G modem but no longer need it for that purpose. I was wondering whether I can now use my TL-MR3220 for two other purposes: as an additional wireless access point and as a means of linking equipment (i.e. printers) to the home network . i have tried connecting the ADSL2 modem/router to the TL-MR3220 via an ethernet cable (one of the 4 LAN ports on the ADSL modem/router to the blue WAN port on the TL-MR3220) but I can get no internet connection through the TL-MR3220.Is this normal i.e. something that the TL-MR3220 is not designed to do, or am I just using the wrong settings ? I have tried a whole range of different settings but none seem to work.
Region : Malaysia
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.8 Build 110418 Rel.43954n
ISP : Celcom
my tl-mr3220 not detect my 3g usb modem dlink dwm-156.
Region : Malaysia
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.13.12 Build 120703 Rel.58323n
ISP :
I'm using the TL-MR3220 hardware version 2.0. Firmware version 3.13.12 Build 120703 Rel.58323n. I'm using D-Link DWM-156 3.75G HSUPA USB Adapter.The problem I'm encountering is the router does not auto detect the 3G USB adapter when I power up the router. The router will detect the 3G adapter only when I plug out and plug in the 3G USB adapter. I used to have the same router but version 1.2. Version 1.2 does not have this problem.
Region : Finland
Model : TL-MR3220
Hardware Version : V2
Firmware Version : Newest
ISP : Sonera
I have a TP-Link TL-MR3220 and Huawei E3276 USB-modem (Sonera, Finland)Is there some update or advices, that can i use this huawei with MR3220? Or when update releases?
]Region : Philippines
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.14.2
ISP : globe telecomms inc.
i just bought an antenna for my new tl-mr3220 v2 router that is 9db. my current one is he 5db that was supplied together wit the unit. then when i installed the new antenna, instead of an increase in the range it lower than my old one. is there any specific antenna or type that you can use? if so what types of antennas?
Region : France
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP : orange
i have installed TL-MR3220 after my livebox (orange french box), my MR3220 is configurer on the DMZ zone in the livebox, internet is ok on the pc but when adsl signal is down on the livebox, the MR3220 don't switch to 3G connexion. The wan led is alway on in the router. But if i unplug the wn cable, the router switch on the 3G connexion. If i plug the wan cable the router kill 3G and use wan connexion.
How can i config my WAN config on the router for automatic switch by the router. Actually, the WAN config is fixed address (DMZ address in the livebox) Whis PPPOE id, the router can't connect. The livebox modem can't work on briddge.
Region : Sweden
Model : TL-MR3220
Hardware Version : V1
Firmware Version : TL-MR3220_v2_120822
ISP : Telia, Sweden
I managed to get my Huawei E3131 from ISP Telia in Sweden to work for 4 days, from the detailed specification from my ISP I can see 1,9GB of data was sent/received with modem+router during those days. The router lost contact with the modem about 3 times during those 4 days but after a restart it was up and running again.
After those 4 days the router cannot find the modem anymore and even though I have upgraded the firmware it does not work. (I have tried both firmware versions available online without success).
I cannot find my Huawei modem in the compatibility list over "Other Location" compatible modems since Sweden is not even an option.
How is it possible that I managed to get it to work for a few days but after that not again? I have tried connecting the 3G-modem to the laptop and then it works perfectly.
Region : India
Model : TL-MR3220
Hardware Version : V1
Firmware Version : TL-MR3220_V1_121123
ISP : Reliance Netconnect +
I have reliance ZTE AC2726 modem and i am trying to connect it with using the latest firmware version 121123. Router is able to detect the modem but when it tries to dial the connection is not established and reset the router after retrying 2-3 times. It was working perfectly fine earlier when i was on 120309 firmware version. So i tried downgrading my firmware version to 120309 and again it started working. I am not sure why the latest firmware version is not working with this device. Ideally the new firmware versions for a router should fix the existing issues and all the modems which were working earlier should work.
Region : CzechRepublic
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP : Ufon
I have a modem ANY DATA ADU-520L and I would like to know whether you are considering supporting this modem in your router?
Region : India
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.14.2 Build 120817 Rel.55520n
ISP : MTS
i am using tp-link router tl-mr3020.. having problem with internet access..it shows my isp (mts) network and got connected also.. it also shows me send and receive data.. but there is no internet access through web browsers .i have tried multiple web browsers (IE / Chrome / Mozilla Firefox)..but the problem remains same.. my ISP network is MTS .. Huwai Device EC-122 with CDMA 2G network.
Region : Hongkong
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : 123
In order to use public IP provided by the ISP, I have to enter the specific APN.It's however no matter what I type in the field of the APN, the router is still connected to the default APN settings from ISP.I have tried typed wrong string in the field of APN, the router is still connected to the default APN successfully.
Region : UnitedKingdom
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 1.13.1 Build 121123 Rel.56770n
ISP : 3 UK
My Huawei E3231 dongle gives me a strong signal and stable connection and rarely loses connecton when plugged directly into my laptop. In the router, connection duration only lasts, fairly consistently, about 30 minutes. 3 UK base station is in sight and only about 90metres away. I have to power off/on the router and turn off/on the wireless button on the laptop to restore connection. i've tried setting idle times etc and other things in the router settings but no joy. The OS is W7 Home Premium SP1.