Cisco Infrastructure :: Will WIC SHDSL-V3 Able To Support ADSL Line
Apr 10, 2013
I do have a question, is WIC-1SHDSL-V3 able to support ADSL line?
We have WIC-1SHDSL-V3 module used for SDSL line, due to few site need to bring up with ADSL line with 1841 model, but HWIC-1ADSL module already EOS. The replacement model EHWIC-VA-DSL-A is not compatible to 1841. My architect suggest Symmetric Module like WIC-1SHDSL-V3 could be able to tweak the config to support Asymmetric purpose. I did google but do not found such related topic. Can any expert on this area to advice me?
View 1 Replies
ADVERTISEMENT
Aug 24, 2012
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies
View Related
Nov 8, 2010
We have a fairly major problem with some of our Cisco 877 units (5 in all). All are running 15.2(2)T2 in order to make use of zone-based firewalls and virtual reassembly, and all are exhibiting the same problem. When our ADSL line drops this si shown in syslog
2010-11-09 01:03:06 Local7.Info 192.168.7.1 4733: Nov 9 01:03:05.707: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41799 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident 02010-11-09 01:04:06 Local7.Info 192.168.7.1 4734: Nov 9 01:04:05.946: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41809 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident
[code]...
The "no retrain. sleep 20 seconds" messages continue forever more until somebody power-cycles the router - which is a bit inconvenient as two are 300 miles away. Surprisingly, our event manager applet isn't triggering the reload either, which defeats the object.
View 15 Replies
View Related
Oct 9, 2012
ADSL line do not activate. Telco Confirmed Like is Okay . They have tested no issue observed. Router replaced but did not work. Supspecting Firmware not compatible with telco . Not sure how to confirm on this.
sh ver
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(4)XC7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Tue 31-Jul-07 20:24 by alnguyen
ROM: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
XXXXXXXXXXXXXXXXXXXXXXX uptime is 30 minutes
System returned to ROM by reload at 18:48:26 UTC Wed Oct 10 2012
System image file is "flash:c180x-advipservicesk9-mz.124-4.XC7.bin"(code)
View 1 Replies
View Related
Jun 27, 2012
Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??
And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..
View 4 Replies
View Related
Jan 27, 2011
I have D-link 2640U ADSL2+ modem. Now I have 12Mbps / 1Mbps internet connection. I am planning to move to 24Mbps /1Mbps intenet connection and I want to know if this modem is enough. What is the best modem so I get the full 24Mbps[CODE]
View 7 Replies
View Related
Mar 28, 2012
Is there a way to find in a remote branch the adsl line number in a cisco router 886VA.
When giving show controllers vdsl 0
we can see the upload/download speed but there is no information about the line number. We need this information in order to troubleshoot adsl line problems with our ISP's in remote branch offices.
View 3 Replies
View Related
Feb 19, 2011
Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.
View 2 Replies
View Related
Mar 28, 2011
Can I install 2 ADSL routers on one telephone line with SKY. If I can does this mean that if sky give me 20mb connection, I can get two lots of 20mb using the two routers.
View 2 Replies
View Related
Aug 16, 2012
I have a broadband router (Linksys E1000) which I've flashed with a DD-WRT firmware. After doing so I realized that this router doesn't have an interface for ADSL port(RJ-11). How can I use the Linksys E1000 for my home network?
I've heard that I can use ADSL modem(not a router) & plug the RJ-11 to it & take from it the Ethernet & plug it back to the E1000(in the WAN port) would that mean that I can get just a modem and not a hybrid?
Note: Also, I have to mention that my ISP is using PPPoA & DD-WRT is not supporting it, but i googled & they said that the ADSL modem cab be the rescue. Can I pick any ADSL modem for this specific scenario or am I looking at a specific model?
Secondly, can I use my old router to do the job instead of buying a new ADSL modem ? & is it a good approach ? or should i buy a new ADSL modem ?
Update i turned my DD-WRT router(E1000) to act as access point, since this is the only way that i can use it with the DD-WRT feature. & i think this is better than have nothing :) I can now have the DD-WRT functions ;)
View 1 Replies
View Related
Nov 21, 2012
I have ADSL router Linksys X3000, but I have an issue with it. I have configured it properly (based on internet provider's manual), repeatedly checked it, but router still says that ADSL line is down. I have also another router from Zyxel and it works perfect with same wire and configuration, so I guess the line is fine.
PPP generic driver version 2.4.2 79 PPP Deflate Compression module registered 88 PPP BSD Compression module registered 84 PPPoL2TP kernel driver, V1.0 75 ccp_autowan_sm_thread=> Starts in Unconfigured mode, detecting state! 125 ->
[Code]....
View 4 Replies
View Related
Aug 1, 2011
Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..
View 1 Replies
View Related
Jan 19, 2012
Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
View 3 Replies
View Related
Jan 3, 2013
We have the Cisco Cat4510 with the 2 Sup-6Es as follows:
5 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
6 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
Each line card comes with dual 10Gig Ethernet X2 Optics. I am currently using int g5/1 and g6/2. I tried to connected a server to the int g5/2 and assigned the poper parameters(VLAN, speed, ...etc) but I am the int is showing down. Is there some type of limitations in using the second port of each line card?
View 1 Replies
View Related
Mar 5, 2012
On my old router I could access the line stats on the home page giving me Attenuation and SNR margin, this allowed me to keep an eye on line quality, there seems to be no equivalent info on the X2000. Is this on a hidden page like the advanced wireless page.
View 1 Replies
View Related
Feb 14, 2013
Region : Argentina
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : ?
ISP : Manx net
Within a property without an available adsl line I'm simply trying to network a wireless laptop with a wireless printer. Both devices recognise the router, etc, but problem sending file for printing to the printer. (laptop does not detect printer). Is the lack of an internet connection the issue or simply a configuration issue?
View 9 Replies
View Related
Dec 6, 2012
We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
View 2 Replies
View Related
Nov 9, 2012
I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
View 7 Replies
View Related
Jul 10, 2012
I have a 1941 Cisco router with WIC-!AM-V2 card that is uning pots( regural phone ) line for data traffic.the problem I am having is the line is establishing connection but it intermittently dropos.The router is configured to dial to Centraal office and I have more that 100 other locations with the same setup that are working fine. The only differene on htis one is it is going thru a PBX line.
View 1 Replies
View Related
Oct 31, 2011
I have a brand new 2911-TS running 2900-universalk9-mz.SPA.151-4.M1. I have connected the async lines to several devices including ASA5510's, 7206V XR and 6506es. I'm experiencing issues where I go to connect to the console port of one of my devices and my access is denied as if the port was already in a session. I clear the line and try again, same response. If I swap that line with a known functioning line I see lines and lines of output as if the device I was trying to connect to was constantly sending data to the console port. I've not had this problem on any of my older Cisco terminal servers. I opened a TAC case and they had me RMA the HWIC module. I cannot find any information about setting some sort of buffer limit or session timeout. I feel this is a configuration, or mis-configuration issue.
View 8 Replies
View Related
Nov 20, 2011
I can connect to my router but not to Internet, it seams that ADSL line "disconnects" my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great
View 1 Replies
View Related
Jan 11, 2010
I have bought a WAG320 & ever since I've had it the ADSL line keeps dropping every few hours. The LAN network is fine & I have 7 computers connected to the router wirelessly. When I press the re-set button on the back of the router everything is fine for a few hours then it starts doing it again?
View 9 Replies
View Related
Mar 21, 2012
We have deployed a number of 800 series routers for some of our clients and have found that in many cases they seem to disconnect at an excessive rate. When I connected to the console of one the other day I could see that the virtual-interface for the ADSL connection was down, but not the ATM or DSL interface. If I disconnected the cable and reconnected the virtual-circuit came back up momentarily before disconnecting within a minute.
If I switched off the router for a few minutes and powered it back on it would usually remain up for a few hours. I reconfigured the router again using exactly the same config and it seemed to stay up for quite long periods for 4 or 5 days before reverting to type. [code]
View 2 Replies
View Related
May 5, 2013
Need config for a 1760 to support AT&T's ADSL 6meg, I would like to compare it to what I have.
View 2 Replies
View Related
Mar 22, 2012
My customer need 3G+WiFi+ADSL, Does CISCO887VGW-GNA-K9 will support ADSL or not
View 3 Replies
View Related
Mar 24, 2013
does Cisco 877 router support DSL (not ADSL?). i have tried connecting a dsl line and cant get ATM interface to come up - username and password are correct.alternative option: Can i get cisco 877 to form a ipsec tunnel using LAN port (not dialer interface) ? basically i want this 877 to act like asa 5505 where i can connect a LAN cable coming out from DSL router?
View 3 Replies
View Related
Aug 29, 2012
I read the document, [URL]
[
Q.I have Cisco 6700 Series line cards today with Centralized Forwarding Cards (CFCs). Are these line cards supported in a Cisco Supervisor Engine 2T system?
#
A. A Cisco Supervisor Engine 2T system will support all Cisco 6700 Series line cards with CFCs.
]
So, As long as the 67XX line card is using CFC, it is compatible with Sup-2T.
I also find the IOS release note indicate the 6704-10G with CFC is supported by Sup-2T, but it require 512M memory.
[URL]
The bug details is not disclosed. So I further search what the default memory size of the WS-F6700-CFC is, then I found here says it is only supported by Sup720 and no memory upgrade option, which means must upgrade to DFC4, in another words, it is not compatible with Sup-2T
[URL]
WS-F6700-CFC:
Centralized Forwarding Card (CFC) for use on WS-X67xx Ethernet modules. This daughter card is supported only by the Supervisor Engine 720. There are no memory options for this daughter card. default memory: 256M
So my question is: whether “WS-X6724-SFP with CFC” and “WS-X6704-10G with CFC” compatible with Sup-2T without upgrading to DFC4 daughter card, and do they support in VSS-2T?
View 4 Replies
View Related
May 9, 2013
We have ACS 5.3 with built in ACS View, does PI 1.3 support it? We have set up in PI 1.3 but unable to see the authentication records for clients, I wonder if they are compatible.
View 4 Replies
View Related
Nov 14, 2011
Assuming I have the following setup: Cisco 7604 Cisco Systems Cisco 7600 4-slot Chassis System OSR-7600 Clock FRU 1 & 2WS-F6K-MSFC2A Cat6k MSFC 2A daughterboard Rev. 4.0 WS-F6K-PFC3B Policy Feature Card 3 Rev. 2.4 WS-SUP32-GE-3B 9 ports Supervisor Engine 32 8GE Rev. 4.6 WS-X6148A-GE-TX 48-port 10/100/1000 RJ45 EtherModule Rev. 4.1WS-X6548-GE-TX SFM-capable 48 port 10/100/1000mb RJ45 Rev. 11.3 The SUP32-3c says it supports both L2VPN and L2TPv3, however the line cards are effectively 6500 line cards and I was under the impression the 6500 didn't support these.
If the supervisor supports a feature does that mean it is globally supported on a switch? Or do I need to check the compatibility of these line cards as to if they support these features?
View 1 Replies
View Related
Apr 23, 2012
I am thinking about running some third-party unified communications apps under VMWare ESXi5 on a Cisco SRE 900 module. According to the Cisco docs, third-party apps are supported on these modules (see table below) but the app in question is NOT on Cisco's list below.
[URL]
Some questions:
1. As long as the third-party app is capable of running under VMWare/VSphere ESXi5, is there anything on the SRE that would prevent you from running this third-party app even though it's not on Cisco's list?
2. What is Cisco's policy on the use of third-party apps that are not on their list? For example, will they take a support call on the SRE running a non-listed app. (I don't want to void any sort of support contract through the use of a third-party app not on their list).
View 2 Replies
View Related
May 10, 2011
we have a Cisco 2851 router and bought the following IOS::
System image file is "flash:c2800nm-spservicesk9-mz.124-25d.bin"
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(25d), RELEASE SOFTWARE (fc1)
I thought this version was supposed to have IPv6 support?
TEST(config)#ipv6 unicast-routing ^% Invalid input detected at '^' marker.
TEST(config)#
which IOS should we buy?
View 1 Replies
View Related
Apr 27, 2011
i will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.
View 1 Replies
View Related
May 6, 2012
I am working on my CCENT after getting my A+. I have an old 3600 router and I am following CBT Nuggets to configure it. CBT Nuggets seems to have an IOS that supports VLAN and IP Addresses and it looks like mine only goes up to Token Ring so it doesn't mirror the instruction. I know it's an old router but is there a software release (like the 12.4 maybe?) that would allow me to follow the CBT Nuggets more accurately so that I can set the switch up for IP Addresses and VLAN instead of limiting me to token ring?
View 1 Replies
View Related
