Cisco WAN :: 1760 Support For AT&T's ADSL?

May 5, 2013

Need config for a 1760 to support AT&T's ADSL 6meg, I would like to compare it to what I have.

View 2 Replies


ADVERTISEMENT

Cisco WAN :: Does 887VGW-GNA-K9 Support ADSL?

Mar 22, 2012

My customer need 3G+WiFi+ADSL, Does CISCO887VGW-GNA-K9 will support ADSL or not

View 3 Replies View Related

Cisco WAN :: Does 877 Router Support DSL (not ADSL)

Mar 24, 2013

does Cisco 877 router support DSL (not ADSL?). i have tried connecting a dsl line and cant get ATM interface to come up - username and password are correct.alternative option: Can i get cisco 877 to form a ipsec tunnel using LAN port (not dialer interface) ? basically i want this 877 to act like asa 5505 where i can connect a LAN cable coming out from DSL router?

View 3 Replies View Related

Cisco Infrastructure :: Will WIC SHDSL-V3 Able To Support ADSL Line

Apr 10, 2013

I do have a question, is WIC-1SHDSL-V3 able to support ADSL line?
 
We have WIC-1SHDSL-V3 module used for SDSL line, due to few site need to bring up with ADSL line with 1841 model, but HWIC-1ADSL module already EOS. The replacement model EHWIC-VA-DSL-A is not compatible to 1841. My architect suggest Symmetric Module like WIC-1SHDSL-V3 could be able to tweak the config to support Asymmetric purpose. I did google but do not found such related topic. Can any expert on this area to advice me?

View 1 Replies View Related

Cisco WAN :: 2911 - Support Interface ADSL Module Like Backup Link?

Apr 27, 2011

i will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.

View 1 Replies View Related

Cisco WAN :: Connecting ADSL Line On HWIC-ADSL On Router 2901?

Aug 24, 2012

i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday   the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?

View 2 Replies View Related

Cisco WAN :: 1760 - Can't Ping Other PC

Jul 15, 2012

I've made a static route between a  Cisco Router 1760 and a Cisco Router 2651xm using crossover cable to  connect to their Fast-Ethernet ports so this is the configuration:

2651xm(config)#ip route 192.168.10.0 255.255.255.128 192.168.1.0.

And the other router's configuration:

2651xm(config)#ip route 192.168.10.0 255.255.255.128 192.168.1.0 (Same thing)
The IP of the 2651xm is 192.168.10.2
The IP of the 1760 is 192.168.10.1.3

I'm I doing it wrong? is the destination wrong? I can't seem to ping any  other IP. I've got another laptop. I've put a static IP of  192.168.10.5, the primary Laptop is using has an IP of 192.168.1.138.  I'm trying to PING the 192.168.10.5 laptop. But this doesn't work.

View 35 Replies View Related

Cisco VPN :: 1760 Usage As VPN Server And NAT

Feb 28, 2011

I am trying to setup a VPN server on my router at home so I that I can access my network remotely.  The router has f0/0 as a dhcp interface connected to a cable modem.  I have a switch card in it and vlan interfaces for my inside/private subnets.  I NAT/PAT the inside vlan interfaces/subnets to the f0/0 dhcp address from the cable modem.  I have found a ton of configs for this but nothing that shows it with a NAT setup.  I have used a few examples I found that are close to my setup.  I am able to connect and the cisco lock closes.  But I am not able to do anything. When checking the cisco client stats the sent numbers keep counting up but the received number stays at zero.  Any good config that I can use or have a good link?  I am also running CME on this router.

View 1 Replies View Related

Cisco WAN :: 1760 To Translate Existing Qos

Jan 21, 2013

I currently have a pair of Adtran Netvanta 1224R units that I want to replacce with Cisco 1760 routers. How can I translate the existing QoS (relevant sections below) on the Adtrans to work.

View 2 Replies View Related

Cisco VPN :: 1760 - Cannot Ping Clients

Oct 21, 2011

I have a Cisco 1760 configured as easy VPN server. Using the cisco VPN  client I can connect to the VPN server. The problem is that there is no  ping between clients. When I connect several clients to the VPN server  there is no ping between the clients. But when I login into the router I can ping the clients and make ssh  remote logins into the clients. It seems that there is no access between  the clients and they cannot communicate at all.
 
The cisco router is placed in DMZ zone. Remote clients can connect into the router.

Here is the configuration of the VPN server:
 
[code]
!
version 12.4
service timestamps debug datetime msec

[Code]....

View 4 Replies View Related

Cisco VPN :: How To Change Password On 1760

Oct 16, 2012

I have just started supporting a client with a Cisco 1760 on site.  They also use the VPN on this device.  I can get to the web interface but for the life of me I cannot find out where I change the VPN password.  They just terminated an employee and I need to do this. 

View 13 Replies View Related

Cisco :: Configure 1760 Router As VPN Server?

Oct 20, 2011

I configured one Cisco 1760 router as VPN server using easy VPN Server. The clients can connect to the VPN server successfully. The problem is that there is no ping between the clients. They cannot see each other into the VPN network.The router has just one port.Do I need special configuration of the VPN sever in order to allow the VPN clients to connect each other or I need other type of VPN?

View 2 Replies View Related

Cisco VPN :: Configure 1760 Router As VPN Server

Oct 10, 2011

I have a old Cisco 1760 router with VPN module. I want to use it as VPN server.I clear all the configuration of the configuration. I want to use the SDM to configure the VPN server.When I tried to configure the VPN sever from the SDM wizard this message appears:"There are no authorization lists configured on this router".

View 2 Replies View Related

Cisco WAN :: Direct Connect A 1721 And 1760

Feb 10, 2012

I just purchased one of each of the above, both with 1ea WIC 1DSU-T1, and would like to connect them directly to each other in a lab scenario.  Do I need to have an RJ48 cable or will an RJ45 work?  I have them connected now, but they are not seeing each other. They are connected via S0 on the 1721 and S1/0 on the 1760.

View 5 Replies View Related

Cisco Switching/Routing :: 1760 - Cannot Ping Next Hop

Mar 1, 2012

I just got a new 1760 router, I have an issue.
 
My FastEthernet 0/0 interface uses DHCP and got 172.16.2.126 /16.
My Ethernet 0/0 interface is my internal interface, it has static 192.168.0.1 /24.
On the Ethernet 0/0 interface, I have a PC attached, IP 192.168.0.150 /24.
 
The router's gateway is set to IP 172.16.1.1
 
My PC can ping 192.168.0.1 and can ping 172.16.2.126 (both interfaces of my router).
My router can ping anywhere on the Internet.
But my PC cannot ping 172.16.1.1. Firewall disabled, all security disabled.

[code].....

View 1 Replies View Related

Cisco Switching/Routing :: Cannot Get Out Of Rommon Mode 1760

Dec 10, 2011

I'm currently pursuing to take my CCNA and am currently studying for it, but have recently encountered a problem with one of my 1760 routers that I can not solve.Yesterday I went to boot up my router like normal, however when I went into hyperterminal I noticed the router was in Rommon mode. Thinking I could change the configuration registry, I tried to bypass the NVRAM by using confreg 0x2142. However this still causes the router to go into Rommon mode. I am getting an error that states that there is insufficient memory to load the IOS image. [code]
 
I have used the dir flash: command and can see the IOS image, and try to boot from it (boot flash:iosimagename) but it will still go back into rommon mode. I also just swapped the RAM from my other 1760 into this 1760 and it booted up and went into normal configuraiton mode without any issues. However, the other router now will not load it's IOS image and I get the exact same error.I'm at a loss here, and have searched to figure out where or how I can just wipe the router clean to try and start fresh, but cannot get out or Rommon mode. The only thing I can think of is that the RAM went bad since it wont boot up either machine.

View 1 Replies View Related

Cisco WAN :: 1760 - Packet Drops In Serial Interface

Feb 11, 2013

We have a Cisco 1760 router . We are facing sevier packet drops in the serial interface.
 
When i swap the router with another router link is working working fine.
 
Troubleshooting steps taken

1.       Swap the serial cable with another working cable : no change in state

2.       Reconfigure the encapsulation commands (with PPP and HDLC) : no change in state

3.       Try with a decreased MTU packet Ping : no change in state

4.       Decreased the Input queue and increased the output queue size using   hold-queue in command : Comparatively the packet drop is reducing but still a 10 percent drop is happening.

View 1 Replies View Related

Cisco WAN :: 1760 Unable To Enable Policy Map On Interface

Sep 6, 2012

Class and Policy maps are defined properly but when I am going to apply the policy-map on interface ,throwing an error as "'set' command is not supported in a 2nd level policymap".
 
Class/Policy map configuration given below ....
 
class-map match-any cm_traffic_control
  match access-group name acl_traffic_control
class-map match-any BE
  match access-group name be
[Code] ....

View 8 Replies View Related

Cisco WAN :: 1760 V - Unable To Ping External Addresses

Mar 1, 2010

I have a 1760-v router set up at my home lab and I am unable to access IP addresses outside my local network.  I have my Cisco router's fast Ethernet port connected to a small net gear router which then connects to my cable modem.  The Cisco router is able to ping local address fine, but when I try to ping an outside address or domain name it times out.  However, when I am at the CLI and type something like Ping { URL}, it resolves Google's IP address but it will not ping it.  I have IP DEFAULT-GATEWAY and IP NAME-SERVER both pointing to my net gear router and pointing to my ISP's DNS server.

View 3 Replies View Related

Cisco WAN :: 1760 Translate Existing QoS On Adtrans To Work On Routers

May 1, 2013

I currently have a pair of Adtran Netvanta 1224R units that I want to replacce with Cisco 1760 routers. How can I translate the existing QoS (relevant sections below) on the Adtrans to work on the Cisco routers.

View 3 Replies View Related

Cisco Switching/Routing :: Can't Configure Data T1 On 1760 Router

Nov 18, 2012

For the past few days I've been attempting to configure a data T1 on a Cisco 1760, but I'm stuck at:

Serial0/0                  <our ip address>    YES NVRAM  up                    down
 
To provide a bit of background. This router used to be configured with a T1 via Frame-Relay; which worked fine. Now we recently change offices and providers, and the provider did not offer any information as to which encapsulation type to use, and if Frame-Relay which DLCI to use, etc.
 
Now I've been trying to setup the T1 connection and testing various settings such as encapsulation HDLC and PPP, but no luck. I also played around with the line codes and framing; which resulted in the following framing sf int down, line prot down, framing esf int up, line prot down. Regardless no luck.
 
Now I've been following several guides and examples mainly the following: [URL] In this guide they make mention of a WIC-1DSU-T1-V2, but as you can see in the show diag snippet at the bottom; we have a WIC-1DSU-T1 version 1.5. I dont' know if this poses a problem for us.
 
Throughout the entire process I've seen a few irregularities for example:

1. Router(config-if)#service-module t1 cablelength short 110ft
^
% Invalid input detected at '^' marker.
 
The IOS doesn't recognize any command with service module t1 ca , and the only recognized command with C is clock.
 
2. If I enter the following list of commands under the serial interface:

!
interface Serial0/0
ip address 10.0.0.51 255.0.0.0
service-module t1 framing esf
service-module t1 linecode b8zs
service-module t1 timeslots 1-12 speed 64

[code]...
 
And I do a sh run all I get is the following:

!
interface Serial0/0
ip address 10.0.0.51 255.0.0.0
load-interval 30
!
 
Although i can do a show service-module s0/0 I can see all of the configured parameters (see below)
 
Module type is T1/fractional
Hardware revision is 0.128, Software revision is 0.2,
Image checksum is 0x73D70058, Protocol revision is 0.1
Receiver has no alarms.
Framing is ESF, Line Code is B8ZS, Current clock source is line,
Fraction has 24 timeslots (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec.
Last module self-test (done at startup): Passed

[code]...

View 19 Replies View Related

Cisco Switching/Routing :: 1760 - DHCP To Multiple VLans

Mar 13, 2012

I can not get dhcp to work.I can ping from the switch to both vlans...
 
here is my config for the router.....
 
Router is a 1760
Current configuration : 1379 bytes
!
version 12.4
service timestamps debug datetime msec

[Code]....

View 1 Replies View Related

Cisco Switching/Routing :: 1760 Crash Info Not Recovers At Flash

Aug 10, 2012

Got a problem with my 1760 router. Bought it from ebay and booted it on today and got this error,It has 180224K/16384K bytes of memory and 2 paritions of 32768K flash.I erased both partitions and put a different version of the IOS on (still 12.4) and there is no difference, still get the errors.These aren't on any of my other 1760 routers so I assume they are linked to the problem.

View 3 Replies View Related

Cisco Switching/Routing :: 1760 / Make Router To Drop Packets Instead Of Rejecting Them?

Mar 31, 2012

I've got a 1760 router which uses port forwarding (25, 80 and 443) for my internal network services. If, let's say, I try to open a FTP connection on the router, of course the connection will be refused. Is there a way to make the router DROP the packets instead of rejecting them? My Linux iptables configurations drop packets who fail the firewall test, so I would like the router to perform that behavior.Commands for port forwarding:ip nat inside source static tcp 10.10.0.1 80 int f0/0 80 (these work fine)

View 4 Replies View Related

Cisco :: Monitor Routers 2610 / 2801 And 1760 With Monitoring Software Called Zenoss?

Sep 4, 2011

I am trying to monitor routers Cisco 2610, 2801 and 1760 with a monitoring software called zenoss. and I cant see on this devices the powersupply state, temperature sensor, fan state, i dont know if this models of routers cant support the monitoring of this component on the devices.what can i do to monitoring this component? what kind of Oid I can use to get this components state?

View 4 Replies View Related

Cisco WAN :: 1760 Point To Point Fiber Connection

Feb 28, 2012

We have two locations 10 miles apart and need connectivity between them. A local provider can run a 30MB fiber connection between the 2 sites at a very reasonable cost. We would have to provide the routers however. I have worked with Cisco routers before with T1 channelized connections but am unsure how the the fiber would connect to a Cisco router in this scenerio. I need to know how such a connection to the routers at each end would take place, specifically what WIC or whatever else would be needed. I currently have a 1760 router at each site but realize that they are old and I m,ay have to replace them with newer models.

View 11 Replies View Related

Cisco VPN :: 1760 / Site-to-site Vpn Gw Replacement

Mar 13, 2011

I am about to replacement a 1760 which doing a site-to-site vpn with one of our branch by a 2811. The config will stays the same- no change at all. My question is one i was the current config of the 1760 load up on the new router with all the cables connected properly, will both router will go to IKE phase and IKE phase 2, and at the end get the QM_IDLE  without any further configuration or troubleshooting.

View 1 Replies View Related

Wireless :: Can Wireless Router Support Up To 100 User Including Support Network Printer

Feb 16, 2011

can wireless router support up to 100 user including support network printer

View 1 Replies View Related

Cisco WAN :: 837 - Simple ADSL Configuration

Feb 11, 2011

I need to configure ADSL on my 837 Router with simple configuration. The WAN IP address is dynamic from my ISP. I checked many websites and found different configurations everywhere. I don't know which is best suited for me. I used SDM and configured ADSL. When i checked the configuration from console i found that there is atm0.2 and dialer 2 configured with my settings. I cannot understand what is the purpose of atm0.2 and dialer 2 when atm0 and dialer0 are there. Is there a doc on ADSL config on 837?
 
interface Ethernet0 ip tcp adjust-mss 1412 exitinterface ATM0.2 point-to-point no shutdown pvc 0/35  pppoe-client dial-pool-number 1  exit exitinterface Dialer2 exitdefault interface Dialer2interface Dialer2 ip mtu 1452 no shutdown ip address negotiated dialer pool 1 dialer-group 1 encapsulation ppp dialer idle-timeout 120 dialer fast-idle 20 ppp authentication chap pap callin ppp pap sent-username username ppp chap password 0 password exitdialer-list 1 protocol ip permit 

View 1 Replies View Related

Cisco WAN :: 2911 / Configure BGP Over The ADSL?

May 19, 2011

I've got a 2911 with a primary ethernet link to the ISP, with BGP running over it.  There's also an ADSL module in it, which will connect into the same ISP AS. how do i configure BGP over the ADSL so that it sits there doing nothing until the primary link fails?  Do i need to setup a new instance of BGP with a different AS on the router or can it sit in the same AS as the primary link?

View 1 Replies View Related

Cisco WAN :: ADSL Configuration On 887 Router?

Aug 1, 2011

I am installing a Cisco 887 to a ADSL2 Circuit and I cannot connect to the ADSL eventhough the show interface shows that both the ATM0.1 and Dialler 0 is up.
 
The configuration of the router is below.
 
Building configuration...
 
Current configuration : 5980 bytes
!
! Last configuration change at 11:12:58 PCTime Wed Aug 3 2011 by cisco

[Code].....

View 9 Replies View Related

Cisco WAN :: 2600 - How To Use DMZ Like ADsl Modem

Mar 14, 2013

I am new using cisco router 2600, i want to use dmz like adsl modem to direct ip public to ip lan like 180.15.22.x.x to ip lan 192.168.1.2 ( lrouter mikrotik )  outside to inside so when i call ip public then forrward to mikrotik

View 2 Replies View Related

Cisco WAN :: 877 ADSL Firmware Change Log

Feb 1, 2011

Where I can find the change logs for the ADSL Firmware's.I realize each firmware comes with its individual bug fixes, however there is usually a significant difference between the shipped firmware and latest firmware available.i.e. the 877m is shipped with 3.0.14 and the latest is 3.0.33. We have a handfull of miscellaneous issues, across a variety of hardware and customers, and would like to scan through the change logs to see if any of these issues were addressed by a previous bug fix.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved