Got a problem with my 1760 router. Bought it from ebay and booted it on today and got this error,It has 180224K/16384K bytes of memory and 2 paritions of 32768K flash.I erased both partitions and put a different version of the IOS on (still 12.4) and there is no difference, still get the errors.These aren't on any of my other 1760 routers so I assume they are linked to the problem.
View 3 RepliesOur 6500 was reboot by self with crash info and i found it was happened by CPU HOG. The log is below for CPU HOG and you can see many times from attached crash info file.
%SYS-SP-3-CPUHOG: Task is running for (16000)m secs, more than (2000)m secs (15/12),process = RPC pagp_switch_mp2sp.
[code]....
I think this process made high CPU & memory issue and then there were internal communication fail.. isn't it? So i need to know what PRC pagp_switch_mp2sp is to prevent next issue.
We have Cisco 3945 Router and generating crashinfo while firing PRI from this Router.
View 1 Replies View RelatedMy asa5505 frequency restart and create a crash-infor file.
View 3 Replies View RelatedTrying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
I just got a new 1760 router, I have an issue.
My FastEthernet 0/0 interface uses DHCP and got 172.16.2.126 /16.
My Ethernet 0/0 interface is my internal interface, it has static 192.168.0.1 /24.
On the Ethernet 0/0 interface, I have a PC attached, IP 192.168.0.150 /24.
The router's gateway is set to IP 172.16.1.1
My PC can ping 192.168.0.1 and can ping 172.16.2.126 (both interfaces of my router).
My router can ping anywhere on the Internet.
But my PC cannot ping 172.16.1.1. Firewall disabled, all security disabled.
[code].....
I'm currently pursuing to take my CCNA and am currently studying for it, but have recently encountered a problem with one of my 1760 routers that I can not solve.Yesterday I went to boot up my router like normal, however when I went into hyperterminal I noticed the router was in Rommon mode. Thinking I could change the configuration registry, I tried to bypass the NVRAM by using confreg 0x2142. However this still causes the router to go into Rommon mode. I am getting an error that states that there is insufficient memory to load the IOS image. [code]
I have used the dir flash: command and can see the IOS image, and try to boot from it (boot flash:iosimagename) but it will still go back into rommon mode. I also just swapped the RAM from my other 1760 into this 1760 and it booted up and went into normal configuraiton mode without any issues. However, the other router now will not load it's IOS image and I get the exact same error.I'm at a loss here, and have searched to figure out where or how I can just wipe the router clean to try and start fresh, but cannot get out or Rommon mode. The only thing I can think of is that the RAM went bad since it wont boot up either machine.
For the past few days I've been attempting to configure a data T1 on a Cisco 1760, but I'm stuck at:
Serial0/0 <our ip address> YES NVRAM up down
To provide a bit of background. This router used to be configured with a T1 via Frame-Relay; which worked fine. Now we recently change offices and providers, and the provider did not offer any information as to which encapsulation type to use, and if Frame-Relay which DLCI to use, etc.
Now I've been trying to setup the T1 connection and testing various settings such as encapsulation HDLC and PPP, but no luck. I also played around with the line codes and framing; which resulted in the following framing sf int down, line prot down, framing esf int up, line prot down. Regardless no luck.
Now I've been following several guides and examples mainly the following: [URL] In this guide they make mention of a WIC-1DSU-T1-V2, but as you can see in the show diag snippet at the bottom; we have a WIC-1DSU-T1 version 1.5. I dont' know if this poses a problem for us.
Throughout the entire process I've seen a few irregularities for example:
1. Router(config-if)#service-module t1 cablelength short 110ft
^
% Invalid input detected at '^' marker.
The IOS doesn't recognize any command with service module t1 ca , and the only recognized command with C is clock.
2. If I enter the following list of commands under the serial interface:
!
interface Serial0/0
ip address 10.0.0.51 255.0.0.0
service-module t1 framing esf
service-module t1 linecode b8zs
service-module t1 timeslots 1-12 speed 64
[code]...
And I do a sh run all I get is the following:
!
interface Serial0/0
ip address 10.0.0.51 255.0.0.0
load-interval 30
!
Although i can do a show service-module s0/0 I can see all of the configured parameters (see below)
Module type is T1/fractional
Hardware revision is 0.128, Software revision is 0.2,
Image checksum is 0x73D70058, Protocol revision is 0.1
Receiver has no alarms.
Framing is ESF, Line Code is B8ZS, Current clock source is line,
Fraction has 24 timeslots (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec.
Last module self-test (done at startup): Passed
[code]...
I can not get dhcp to work.I can ping from the switch to both vlans...
here is my config for the router.....
Router is a 1760
Current configuration : 1379 bytes
!
version 12.4
service timestamps debug datetime msec
[Code]....
I've got a 1760 router which uses port forwarding (25, 80 and 443) for my internal network services. If, let's say, I try to open a FTP connection on the router, of course the connection will be refused. Is there a way to make the router DROP the packets instead of rejecting them? My Linux iptables configurations drop packets who fail the firewall test, so I would like the router to perform that behavior.Commands for port forwarding:ip nat inside source static tcp 10.10.0.1 80 int f0/0 80 (these work fine)
View 4 Replies View RelatedI just upgraded several of my C2960S-48FPD-L from 12.2(55)SE to 12.2(58)SE and now almost every time I try to SSH to it the switch reboots and gives me these trace backs ...
07:58:52 CST Thu Apr 14 2011: Unexpected exception to CPU vector 200, PC = 1EADA28
-Trace back= 0x1EADA28z 0x1CDC324z 0x1EA5520z 0x1CDC35Cz 0x1CDD0E0z 0x1CDF0C4z 0x1CE06CCz 0x1CE07F8z 0x1D67348z 0x1D611BCz
Writing crash info to flash:/crashinfo_ext/crashinfo_ext_3
07:58:56 CST Thu Apr 14 2011: Unexpected exception to CPU vector 1100, PC = 121BB98
-Trace back= 0x121BB98z 0x12250FCz 0xFA7540z 0xA807B8z 0xA75DF4z 0xA78080z 0x94B708z 0x9717C0z 0x918DD8z 0x936520z 0x9344BCz 0x9345FCz 0x93484Cz 0x1D67348z 0x1D611BCz
=== Flushing messages (07:58:56 CST Thu Apr 14 2011) ===
Buffered messages: (last 4096 bytes only)
0x00000005 R6 = 0x01224F44 R7 = 0x02A23C6C
000089: *Feb 28 18:03:13.577 CST: %PLATFORM-1-CRASHED: R8 = 0x00000080 R9 = 0x00000000 R10 = 0x00000000 R11 = 0x00000071
000090: *Feb 28 18:03:13.577 CST: %PLATFORM-1-CRASHED: R12 = 0x00034855 R13 = 0x00000280 R14 = 0x01CE0778 R15 = 0x00000000
000091: *Feb 28 18:03:13.577 CST: %PLATFORM-1-CRASHED: R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19 = 0x00000000
[ code]....
I have a Cisco WS-C6513 switch, with a couple of GBIC module cards in it. I am trying to display the part number (or model number) of the modules which are inserted into this module card. How to do that? I don't want to schedule down-time to pull the module(s) - just to read the label! :-)
This shows me info for the "module card": sh module 9 But this doesn't work: sh module 9/6
We have a number of 4507s. Most are managed via VLAN 1 address. All have multiple VLANS for traffic control. When I do a show ARP or show IP ARP the command only shows VLAN 1 info. No entries for any of the other VLANS on the switch.
View 2 Replies View RelatedI have been given 2 x 3750 switches that were a stack, I need to keep the configs on both but how do I make them individual switches again and remove the stack info?
View 3 Replies View RelatedWhat this crash means? This is a 6509 with a single Sup720 Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI, RELEASE SOFTWARE (fc2)System returned to ROM by s/w reset at 04:42:07 PST8PDT Mon Jan 2 2012 (SP by bus error at PC 0x40C6681C, address 0x424B).
View 1 Replies View RelatedOur ME3400 crashed unexpectedly and got the below errors:
meQCY0290A#sh ver
Cisco IOS Software, ME340x Software (ME340x-METROACCESSK9-M), Version 12.2(55)SE, RELEASE SOFTWARE (fc2)
[Code].....
I have 3560X-24T-S switches with IP Services loaded at remote sites that I have been having troubles with. Originally, they had IOS 12.2(58)SE1 on them. I have up to four diverse paths via point-to-point microwave at the remote sites. The Microwave equipment is by Microwave Networks and is a Prodeus M series which Ethernet support. The original issue manifested itself as hardware loopback errors on some of the ports that were connected to the microwave links.
My experience in the past has been that when a hardware loopback error occurred it is usually a bad switch port. In this case however, if I disconnected all of the microwave Ethernet links and rebooted the switch and then connected the Ethernet connections to the microwave links again, everything works fine. No hardware loopback errors. That is, until the next switch reboot. Then the hardware loopback error would return. Interestingly, it would come back on different ports connected to the microwave links every time. So if a reboot was done without disconnecting the microwave Ethernet links the hardware loopback error would change from one microwave link to another after each reboot.
I then went through and read the lengthy release notes for IOS version 15.0(2)SE and found several fixes that I thought could fix my issue. So I downloaded it and updated a couple of the offending switches (not all of them were having this problem). After going through the second update required to resolve the 'open file error' that happens going between 12.2(58)SE1 and 15.0(2)SE the problem seemed to be resolved on the offending switches. So, I went ahead and updated the IOS on all of the switches with point-to-point microwave connections.
I now have one switch that was updated that is crashing and rebooting continuously when the Ethernet links for the point-to-point microwave are connected. Again, if I disconnect all the microwave links and reboot, it comes up fine ands stays fine when the microwave links are connected back up. It will work fine until the next reboot and then the crash and reboot loop starts over again. Below is a portion of the putty log when the crash occurs:
----------------------------------------------------------------------------------------------------------------------
previous memory block, bp = 0x59BF838,
memorypool type is Processor
data check, ptr = 0x59BF860
========= Dump bp = 0x59BF87C ======================
59BF77C: 0 0 0 FD0110DF AB1234CD FFFE0000 56 383FDB4
59BF79C: 212AC68 59BF838 59BF6F4 80000042 1 0 A504F53 543A2050
59BF7BC: 6F727441 53494320 506F7274 204C6F6F 70626163 6B205465 73747320 3A20456E
[code].....
We had an "Event" on our process network at the mill yesterday. I connected a new WS-C3560V2-48TS-S to our network and we lost communications with all of the other switches.
The core is a stack of 3 WS-C3750 switches, one is a -24TS-1U and the other two are -12S-S. These connect to 10 WS-C3560G-24TS and 5 Rockwell Stratix 8000 (IE3000) over fiber. I am planning on replaceing two 24 port switches with the new 48 port. I had the switch configured and running at my work bench. It was connected to the network with one sfp module and ran all weekend with no issues. Yesterday afternoon I took it to the network cabinet and installed it. I powered it up and connected two sfp modules to the fiber patch panel and made the connection at the core stack.
Everything looked OK. I had communication link lights working on everything. Within minutes, we lost communication with every switch connected to the core stack. I shut down the new 48 port switch and the network slowly came back up.
The new 48 port is configured with Flex Links for the fiber redundancy protocol and was connected to each of the 3750G-12S-S stack members.
I though it might have been a power issue but the stack is UPS protected and shows it has been up for over 10 weeks. I'm not even sure "Crash" is the best decription for what happened. The new switch has a high enough IP address that it would not take over as a IGMP Querier.
I have a cisco 2821 router in rommon and displaying the message '' softwre forced crash '' and '' checksum error'' .I tried to do rommon tftpdnld but as the image is self decompressing into the ram it again crashes with the same error although i have done it with various valid ios but in vain.
View 1 Replies View RelatedThe switch 6500-E is frequently crashing whenever the pm scp process reach 100% .I got it under the command "remote command switch show proce cpu".How to solve the problem. I opened the TAC and the engineer says to upgrade the image12.2(18) sxf.Is there any other work around that would avoid to reimage the switch and reloading.
View 1 Replies View RelatedI got some unexpected System crash, and this happens to 2 different routers on the same network.. (We suffer a Crash and change the router, happens the same to the new router after some time, maybe 40 minutes!!)
Here is the last console report for the new router....
%Software-forced reload
Preparing to dump core...
4w1d: %SYS-2-WATCHDOG: Process aborted on watchdog timeout, process = IP NAT Age
[Code]....
About an hour ago I had the master switch on one of my 3750x (WS-C3750X-48PF-S) stacks crash. The only two items we've found that could have caused this issue are the roughly 1.3 million big buffer misses and several of the following in the syslog
SLT:WARN:No exporter configured for smartlog! I do not have smartlogging turned on, nor is there a netflow exporter configured
sh logging smartlogsmartlog is disabledsmartlog exporter:smartlog pkt length: 64 Total pkts processed: 0Total DHCP Snooping pkts processed: 0Total DAI pkts processed: 0Total IPSG pkts processed: 0Total ACL pkts processed: 0
I did not see any traffic spikes prior to the crash.
This stack has been stable since it's last IOS upgrade from 12.2(58)SE1 to 12.2(58)SE2 back in October 2011 so this has me a little worried.
I am not able to find the exact bug for Cisco 3750E stack - Debug Exception (Could be NULL pointer dereference) Exception (0x2000) error. Closest i can find is CSCsa72400 which only affects ver 12.2(20)SE4.All the stacks (3 switches) are running 12.2(50)SE3, It appears that the switch 1 crashed and reloaded. My hunch is its software but i cant find any related bugs. It could be hardware issue as well ?
View 4 Replies View RelatedProblem I have encountered when upgrading a Cisco 6509 chassis with a new supervisor card from Sup2 to Sup 720b. The 6509 loads and then crashes completely, and when rebooted reloads into rommon.The same upgrade was performed on a similar switch with no apparent problems.
[code]....
I want to know what is this process used for on a catalyst 6500 ? we have got following message in the crash file, probably due to CSCsv77354
Jun 30 16:06:47.099 UAE: %SYS-6-STACKLOW: Stack for process ACE HAPI running low, 0/6000
Our switch had a little crash-fest this morning at 2:30 AM. I did find a web page about diagnosing Software Forced Crash Exceptions, but it did not look like ours was one of the more easily-identifiable ones.
It may be worth noting that we've only used this switch for about a month, everything seemed fine until now. When we got the switch it did not have any GigE modules, and this week we put 2 into it and have been using them for 2 servers.
It looks like the switch was crashing repeatedly over a period of 20 minutes, and then it stopped and normalized. In the logs of the router that this switch uplinks into, we could see the ethernet port flapping during the time that the switch wasn't reachable.
Here's the Show Stack on the switch:
Sfld_3550# show stackMinimum process stacks:Free/Size Name4404/6000 vegas_flash init3352/6000 SaveCrashBuffer5716/6000 CDP BLOB8512/9000 IP Background5596/6000 vqpc_shim_create_addr_tbl5584/6000 SPAN Subsystem5552/6000 SASL MAIN4944/6000 vegas IPC process8704/9000 cdp init process5404/6000 RADIUS INITCONFIG4928/6000 Vegas CrashBuffer5664/6000 URPF stats2536/3000 Rom Random Update
[code].....
I have a WS-C3560X-24 and attached to that are some 9 acces switches, for some weeks now my 3560 reboots some time what couse that the other 9 switches are down for some minuts as well and i dont want this of course. the reboot happens at random times and some times one week not and then like yesterday afternoon it rebooted again.
when i check the Flash directory there is no crash file and when i look at the logging its clean and just shows the startup. it's not the powersuply it's redundend and more L3 switches are attached to this power source and they dont reboot.
L3_AIM#sh versionCisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2011 by Cisco Systems,
[Code]......
I have one Catalyst 6509E chassis and two SUP720. The bootup sequence on SUP 720 (standby hot) failed . Messages that appear on SUP 720, on the console port indicate o software crash. I don't have a flash card in SUP720.
This is the bootup process:
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
[code].....
I've gotten this out of our storage unit here at work: This was not in use, I've restarted it, I can't get into the flash dir,I've tried to restart the switch via the documents I've gotten on the site.I have the lastest iOS version .bin for this switch, but I can't get this to load: here below is what happens when I try.
View 5 Replies View RelatedI have received a sup720-3B from Cisco with an internal 512MB flash(sup-bootdisk). I want to verify what IOS image is on the disk and do not have an spare 6509 chasis. Can I remove the 512 MB flash disk and insert it to my disk0: on my production 6509 with the sup32 that the 720 will repplace and view what is on the disk without corrupting?
View 7 Replies View RelatedI have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
I want to delete the first file c2600-i-mz.122-5d in the flash. Not only delete but also reclaim the memory held by deleted file.I followed a link and i ended up with the c2600-i-mz.122-5d marked as deleted in the flash but the memory was not reclaimed.When I restarted the router, it went to ROMMON mode. This is my understanding when router tried to boot from the flash, It tried to load the first file in the flash. Since the file was marked as deleted therefore Router went to ROMMON mode.Now my question is how could I delete the first file and reclaim the memory on 2600 router?
View 8 Replies View RelatedI tired to upgrade the flash memory on my 871. I have tired to send single break and removing the flash card to drop the 871 to rommon. but no luck, all i get is the below error. I have try restart button on the back and get the same results. How to get the router into rommon mode so i can place the IOS on the flash ?
View 5 Replies View Related