We have a number of 4507s. Most are managed via VLAN 1 address. All have multiple VLANS for traffic control. When I do a show ARP or show IP ARP the command only shows VLAN 1 info. No entries for any of the other VLANS on the switch.
View 2 RepliesI'm trying to examine the ARP table on specific phy ports on a SG300 switch. The Cisco CLI guide shows this syntax:
show arp [ip-address ip-address] [mac-address mac-address] [interface-id]
Using the CLI and the "?" key to get assistance, I'm not successful:
switch3#show arp
configuration Display ARP related configuration
ip-address Filter ARP show by IP
mac-address Filter ARP show by MAC
[Code]...
I don't have http server enabled, I prefer SSH and CLI to do my work.
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedAny "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies View RelatedI have a requirement to monitor all traffic going from the internal LAN to the cloud. The LAN is a layer 2 VLAN which spans multiple Cisco 4507 switched and other smaller switches.
The VLAN has an IP address which the hosts use as the default gateway.
The exit port is on a Cisco 3600X switch connecrted to 4507 #1 via a 10G fiber link. 4507 #1 connects the rest of the LAN. Those switches interconnect via 10G fiber and 1G copper links.
Currently the monitor host is connected to a 1G copper port, configured as a monitor port, on one of the backside 4507s The switch manager says he has the switches configured so that I can see all traffic on the VLAN.
We are trying to setup a new configuration with 2960S as access switchs and a 4507 as a core switch.I want to protect the management IP VLAN of the swich using vrf on the 4507 so we :
SHUT VLAN 1 on every switch (2960 + 4507)
CREATE A NEW VLAN 289 (management vlan) -> IP network : 10.32.126.192/26
L3 VLAN on every switch
VLAN 289 in the VRF XXX on the 4507
create tunk between the switch and the 4507 :
switch mode trunk allowed vlan 200-230
sw trunk native vlan 289
so with this configuration on the 2960 the vlan 289 is UP/DOWN and UP/UP on the 4507 I can access to the 4507 using the IP in the VLAN 289 but i cannot access to the 2960 behind the 4507 CDP connectivity is ok?
I am tring to configure ssh in cisco 4507.After doing so Ican see ssh connection establish from default vlan but getting failed from other vlan.rectify the ssh configuration so that connection estabnlish from any vlan.
View 1 Replies View RelatedI have a really weired thing happening on 6509 device with one of my customers.The device has a SUP 2 (MSFC2) with version 12.2.18SXF17B.
any VLAN interface once administratively down or simply down shows on "show interface status" output as VLAN.While it supposed to show "Routed". However once the port is up it is shows "routed" like it should.
C1921, running version 15.1(4)M2, with licence for "IP base" feature set only.Trying to pass multicast via a PPTP VPN from a Windows XP machine to work around a non multicast-aware WAN link
1. With the IP Base feature set I am able to create a plain PPTP VPN without any encryption; the Windows XP machine can bring it up and unicast data passes through it OK in both directions.
2. But when trying to send multicast, only one-way traffic is observed:i. Windows XP host on far end of PPTP VPN and a local PC both running old Microsoft tool "MPING.EXE", sending and listening for traffic on the groiup 225.100.101.102i. The distant host receives and echoes back the packets received from the local machine + sending its own (confirmed with Wireshark running at the far end)ii. But the local machine directly connected to the C1921 router does not hear any packets from the far end; Wireshark shows only the ones it is sending.
3. Group status ("show ip igmp membership") as far as the C1921 is concerned shows both ends (192.168.50.10 (local end) and 192.168.50.201 (distant end via the PPTP VPN)) joined to the group [code]
4. But "show ip mroute" for that group shows an error; for the source on the far end of the PPTP VPN (having the IP address 192.168.50.201), the source interface is incorrectly shown as GigabitEthernet0/0 (should be Virtual-Access2.1 for that PPTP VPN) and the outgoing interface is shown as Virtual-Access2.1 [code]
5. I have tried adding static mroutes and messing about with parameters for the virtual-template interface for the PPTP VPN, but the problem remains. And if I put another local PC onto a different Ethernet port of the router, the multicast traffic does flow both ways - so the issue is solely with the PPTP VPN.After a week of head-scratching I am getting more and more convinced that it's a bug... but wonder if it is already-known, has a workaround, or a fix in newer firmware?
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedOur 6500 was reboot by self with crash info and i found it was happened by CPU HOG. The log is below for CPU HOG and you can see many times from attached crash info file.
%SYS-SP-3-CPUHOG: Task is running for (16000)m secs, more than (2000)m secs (15/12),process = RPC pagp_switch_mp2sp.
[code]....
I think this process made high CPU & memory issue and then there were internal communication fail.. isn't it? So i need to know what PRC pagp_switch_mp2sp is to prevent next issue.
I have a Cisco WS-C6513 switch, with a couple of GBIC module cards in it. I am trying to display the part number (or model number) of the modules which are inserted into this module card. How to do that? I don't want to schedule down-time to pull the module(s) - just to read the label! :-)
This shows me info for the "module card": sh module 9 But this doesn't work: sh module 9/6
Got a problem with my 1760 router. Bought it from ebay and booted it on today and got this error,It has 180224K/16384K bytes of memory and 2 paritions of 32768K flash.I erased both partitions and put a different version of the IOS on (still 12.4) and there is no difference, still get the errors.These aren't on any of my other 1760 routers so I assume they are linked to the problem.
View 3 Replies View RelatedI have been given 2 x 3750 switches that were a stack, I need to keep the configs on both but how do I make them individual switches again and remove the stack info?
View 3 Replies View RelatedHow do I enable SSH on 4507. I do not see "ip ssh ..." commands config#ip ssh (I do not see "ip ssh " commnd)
Do i need to enable something else?
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
I am having a Cisco 4507 switch. The CPU on the switch is running between 50% to 60% constantly. To troubleshoot I collected some logs using debugs & show commands.
debug platform packet all receive buffer
show platform cpu packet buffered
debug platform packet all count
show platform cpu packet statistics
show processes cpu sorted | exc 0.00
show platform health
show platform cpu packet statistics
show platform health output shows the below process crossing the target value.
%CPU %CPU RunTimeMax Priority Average %CPU Total
Target Actual Target Actual Fg Bg 5Sec Min Hour CPU
Stub-JobEventSchedul 10.00 13.41 10 47 100 500 13 13 10 5462:52
K2PortMan Review 3.00 5.35 15 11 100 500 4 4 3 1799:47
What I need to know is, though these process are running in Low Priority, will there be any issue if the CPU goes high due to these process.
Could not find a valid file in BOOT environment variable. BOOT variable can be set from IOS. To find currently setRom Monitor variables, type 'set' command.
Choosing a boot method, type 'confreg' command.rommon 1
>setPS1=rommon ! >RommonVer=15.0(1r)SG5SupportedFeatures=1ConsecPostPassedCnt=2DiagMonitorAction=NormalCONFIG_FILE=bootflash:cat4500e-
[Code].....
Our organization currently has a Cisco 4507 acting as our core switch and 2 ASA525 firewalls.
Our existing ISP runs into our 4507. Here is the port config.
interface GigabitEthernet7/1
description ISP-DSL
switchport access vlan 10
[Code].....
We have recently purchased a 5Mbit line with a second ISP and will have the line activated tomorrow. In addition, we recently obtained our AS number through ARIN. How would I configure the second ISP to be used for load balancing/failover?
4507 Went To Romon During IOS upgrade.
View 3 Replies View RelatedWe will deploy several 4507 with 2xsup7 as a L2 access switches for our office.Does LAN_Base IOS version support SSO or we need purchase IP_Base IOS (L3)?
View 1 Replies View RelatedSSH has been enabled on our one and only 4507 switch for several months and working fine. A few weeks ago the switch had to be reloaded and when it was back online I couldn't SSH to it. When I connected via the console and typed "show ip ssh" it came back saying I needed to generate the keys. Did that and it starting working again. The same switch had to turned off and on the other day due to a power down in the server room and when it came back the same thing happened again!!
The version of IOS is: cat4000-i5k91s-mz.122.20.EW
Is there any option to configure cisco 4507 to genrate log alert when cpu utilization or port utilization reaches above certain percentage.
View 2 Replies View RelatedI need to configure a port channel between two sw 4507R. with port Giga, but those port are in different modules.
Sw-1
interface GigabitEthernet5/48
description **** Conexion Switch-2*****
[Code].....
I have 4507 switch and I got the error of fan sensor which is mention below [code] What the meaning of FAN Sensor both are Bad/off ?
View 4 Replies View RelatedQoS design problem that I have. I have a client that is deploying new 4507 series switches with SUP6Es. The client will be running lots of voice, streaming video, and video conferencing over the LAN and want to base QoS on Cisco Media net recommendations.
I need to design a new QoS policy with focus on the above media services with basic queuing for critical data services. I have read the Media net design guide and the suggested 12-class model will be too complex to start with but I have seen references to start with a 8-class model with the ability to easily migrate to 12-class in the future. The 8-class model meets all of our requirements but I need to understand how this will work with the 4507 queuing model? [URL]
we have a core switch 4507RE at the data center and 2 departments that connect to it via 10Gig fiber using X2-LRM modules. Each department has a 3 switch stack and both locations are identical w.r.t type and setup scenario.the stack comprises of 1 x 3750E and 2 x 3750G . uplink is from X2 port tengig3/0/1 from the 3750E switch.
All of a sudden dept B started facing problem , where the ping would break and throughput comes around 6 - 7 mbps from that dept to the server behind the core switch. we also noted CRC error on both sides preodically.
we replaced the multimode fiber patch cords, re did the splicing , which stopped the CRC errors to appear.now since morning the uplink port on the 3750E (3/0/1) would suddenly be in "down" state with (err-disabled) as the status when i run sh int ten 3/0/1
and i can also see CRC errors and input errors on the same interface.. if i do shut / no shut .. the port is up and active again.. but this has happned 3 times today.the core swith side is still OK and no CRC / input / output errors are seen..
now on the 3750E i have swapped the 10gig module from 3/0/1 to 3/0/2 . the port is still up but i can see 400 CRC and 500 Input errrors.the module is also OK as i had replaced it with dept 1's module.
For some unknown reason our NMS cannot validate SNMP string configured on catalyst switch 4507. SNMP version is 2c
snmp-server community Cisco RO
snmp-server community Cisco RW
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps entity
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps config
snmp-server enable traps hsrp
snmp-server enable traps syslog
There is Reach ability between NMS server and switch but snmp string is not validating.
Is there a way I can find out the amount of bandwidth i'm using on a particular interface on a 4507 cisco multi-layer switch? It is a gig port and I have it setup for monitoring (spanning) and I see packets being dropped in the "Total Output Drops" area. To me it looks like it must be exceeding the 1gig limit but I don't know a way to check to make sure. I also have the queueing strategy set to FIFO.
View 3 Replies View RelatedI have a 4507 cisco switch loaded with two sup-modules.. [code]
View 5 Replies View RelatedWe have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies View Relatedi have a problem with a cisco cat. 4507 edge switch as when i have a login ssh session to the switch the supervisor engine restart and the redundant Sup. engine becomes the active and so on this problem mainly happen when i have multible SSH session to the switch and it happened very rarely with a single ssh login
the ios version i use is cat4500-entservicesk9-mz.122-54.SG which im using on all my edge switch and they are all working fine excpt this one
I have Catalyst 4507 R-E with one supersor engine n 3 other modules.My question is related to routing of different networks through this switch.I already have certain routes configured which are going to my ISP thru Juniper firewall.(192.168.0.9)I also have Cisco ASA 5510 which i want to use as a backup in case the first one goes down.
View 3 Replies View RelatedI have been trying to reset my Cisco 4507 R-E with sup 10GE engines, and I am not having any luck. I have followed the following document:
[URL]
I have tried "wr erase" and "erase startup-config." I cannot delete the vlan.dat file either. I am using the command "erase cat4000_flash:vlan.dat" and its not working either. I have done these commands several times with no success. When asked if I want to save the config changes, I am answering with a "no" I have not tried to depress the small "reset" button on the front of the sup engines as I read that this just restarts the switch.