Cisco Switching/Routing :: 4507 - New Media Net QoS Design
Aug 25, 2012
QoS design problem that I have. I have a client that is deploying new 4507 series switches with SUP6Es. The client will be running lots of voice, streaming video, and video conferencing over the LAN and want to base QoS on Cisco Media net recommendations.
I need to design a new QoS policy with focus on the above media services with basic queuing for critical data services. I have read the Media net design guide and the suggested 12-class model will be too complex to start with but I have seen references to start with a 8-class model with the ability to easily migrate to 12-class in the future. The 8-class model meets all of our requirements but I need to understand how this will work with the 4507 queuing model? [URL]
View 1 Replies
ADVERTISEMENT
Feb 16, 2012
Any "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies
View Related
Aug 27, 2012
We have 2 sites, each with 2 x 4506 switches which will be connected togther using an etherchannel. The switches will provide access ports for client devices and will be configured with HSRP to provide gateway redundancy. SW1 will be HSRP active.2 metro ethernet links will be installed in each site which will connect back to our HQ sites. OSPF will be used over the backbone to provide resiliency and to allow shortest path routing to each HQ and to prevent traffic over the HQ to HQ link.
The 4506 will be trunked togther with an SVI for providing OSFP adjacency.For the traffic flow from SW2 to HQ2, traffic will hit SW1 and then route back to SW2 and then to HQ2. Is this the best way to do this? Should a second link be connected between switches just for routing or should something like GLBP be used?
View 6 Replies
View Related
Feb 14, 2012
How do I enable SSH on 4507. I do not see "ip ssh ..." commands config#ip ssh (I do not see "ip ssh " commnd)
Do i need to enable something else?
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
View 1 Replies
View Related
Nov 19, 2012
I am having a Cisco 4507 switch. The CPU on the switch is running between 50% to 60% constantly. To troubleshoot I collected some logs using debugs & show commands.
debug platform packet all receive buffer
show platform cpu packet buffered
debug platform packet all count
show platform cpu packet statistics
show processes cpu sorted | exc 0.00
show platform health
show platform cpu packet statistics
show platform health output shows the below process crossing the target value.
%CPU %CPU RunTimeMax Priority Average %CPU Total
Target Actual Target Actual Fg Bg 5Sec Min Hour CPU
Stub-JobEventSchedul 10.00 13.41 10 47 100 500 13 13 10 5462:52
K2PortMan Review 3.00 5.35 15 11 100 500 4 4 3 1799:47
What I need to know is, though these process are running in Low Priority, will there be any issue if the CPU goes high due to these process.
View 1 Replies
View Related
Jun 4, 2012
Could not find a valid file in BOOT environment variable. BOOT variable can be set from IOS. To find currently setRom Monitor variables, type 'set' command.
Choosing a boot method, type 'confreg' command.rommon 1
>setPS1=rommon ! >RommonVer=15.0(1r)SG5SupportedFeatures=1ConsecPostPassedCnt=2DiagMonitorAction=NormalCONFIG_FILE=bootflash:cat4500e-
[Code].....
View 11 Replies
View Related
Nov 17, 2011
I have a typical LAN environment that spans across a large warehouse. I have done a lot of redesigning of the environment to satisfy the need for a disaster recover plan. I now have created a LAN with multiple v lans and must also connect all the access layer switches back to the core switch where the servers are.
I was thinking of something simple such as Port channel of 2 Gbps across the backbone and simple floating static routes . I have then moved my wan access link to a 3750 and implemented routing a CEF at each of the 3 core switches (blue). My question is more of design.
View 1 Replies
View Related
Jun 13, 2012
Our organization currently has a Cisco 4507 acting as our core switch and 2 ASA525 firewalls.
Our existing ISP runs into our 4507. Here is the port config.
interface GigabitEthernet7/1
description ISP-DSL
switchport access vlan 10
[Code].....
We have recently purchased a 5Mbit line with a second ISP and will have the line activated tomorrow. In addition, we recently obtained our AS number through ARIN. How would I configure the second ISP to be used for load balancing/failover?
View 8 Replies
View Related
Jun 22, 2012
We have remote office where we have 2921 router with 6 layer 2 switches. We have few servers which need to be in specific vlan.
2921 router does not have switching engine we are using this to support VOIP.
So on 2921 router i created 6 sub interfaces for each vlan and assign them to their specfic vlans. Then I have trunk connection to switch 1. Now switch 1 connects to all other switches in the network. As our company design all layer 2 switches should be transparent mode. i tested them i can ping from one switch to all other switches.
Router vtp mode i set to transparent mode and from all switches i can ping the router sub interfaces.
View 4 Replies
View Related
Sep 10, 2012
4507 Went To Romon During IOS upgrade.
View 3 Replies
View Related
Apr 26, 2012
We will deploy several 4507 with 2xsup7 as a L2 access switches for our office.Does LAN_Base IOS version support SSO or we need purchase IP_Base IOS (L3)?
View 1 Replies
View Related
Nov 29, 2012
SSH has been enabled on our one and only 4507 switch for several months and working fine. A few weeks ago the switch had to be reloaded and when it was back online I couldn't SSH to it. When I connected via the console and typed "show ip ssh" it came back saying I needed to generate the keys. Did that and it starting working again. The same switch had to turned off and on the other day due to a power down in the server room and when it came back the same thing happened again!!
The version of IOS is: cat4000-i5k91s-mz.122.20.EW
View 1 Replies
View Related
Nov 8, 2012
Is there any option to configure cisco 4507 to genrate log alert when cpu utilization or port utilization reaches above certain percentage.
View 2 Replies
View Related
Nov 29, 2011
I need to configure a port channel between two sw 4507R. with port Giga, but those port are in different modules.
Sw-1
interface GigabitEthernet5/48
description **** Conexion Switch-2*****
[Code].....
View 2 Replies
View Related
May 13, 2013
I have 4507 switch and I got the error of fan sensor which is mention below [code] What the meaning of FAN Sensor both are Bad/off ?
View 4 Replies
View Related
Jan 19, 2012
we have a core switch 4507RE at the data center and 2 departments that connect to it via 10Gig fiber using X2-LRM modules. Each department has a 3 switch stack and both locations are identical w.r.t type and setup scenario.the stack comprises of 1 x 3750E and 2 x 3750G . uplink is from X2 port tengig3/0/1 from the 3750E switch.
All of a sudden dept B started facing problem , where the ping would break and throughput comes around 6 - 7 mbps from that dept to the server behind the core switch. we also noted CRC error on both sides preodically.
we replaced the multimode fiber patch cords, re did the splicing , which stopped the CRC errors to appear.now since morning the uplink port on the 3750E (3/0/1) would suddenly be in "down" state with (err-disabled) as the status when i run sh int ten 3/0/1
and i can also see CRC errors and input errors on the same interface.. if i do shut / no shut .. the port is up and active again.. but this has happned 3 times today.the core swith side is still OK and no CRC / input / output errors are seen..
now on the 3750E i have swapped the 10gig module from 3/0/1 to 3/0/2 . the port is still up but i can see 400 CRC and 500 Input errrors.the module is also OK as i had replaced it with dept 1's module.
View 1 Replies
View Related
Apr 17, 2012
is it possible to run hsrp on two routers (not l3 switch) connected to a l2 switch ? if so does the two routers need a back to back connection ?
i know if use two l3 switches (instead of routers) and connect to a LAN switch then we need a back to back connection between the L3 switches
also can we use hsrp on vss on 6500?
design
1800 router 1800 ROuter
| |
| |
|---------- L2 switch-------------------------------|
if the above design is acceptable how does the routers know which one is active and which one is standby ? if we need a direct connection between two routers they have to be on a seperate subnet and routers dont allow broadcasts - so how will hsrp work on routers ?
L3 switch --------------------------l3 switch
| |
| |
|---------------L2 switch---------------|
View 8 Replies
View Related
May 11, 2011
We are designing a LAN Network for ourselves.The proposed design is as follows:
4 x 2960S switches in a Stack Access-Stack-I 4 x 2960S-PoE switches in a second Stack Access-Stack-II
2 x 3750X switches in a Stack Core-Stack
Now I would like to connect it in the following manner ?First,I would like to use EtherChannel using the 10Gig LinksSecondly, I would like to use Cross-Stack EtherChanel too.I have given a graphical illustration of the connectivity Now my Qs: a) Will the 2960S supports EtherChannel using the 10G links and the 3750X too... b) Does the proposed solution will work... or It will have any problems.
View 4 Replies
View Related
Apr 25, 2012
I've been tasked to come up with a design to segment our internal network to reduce broadcast domain size. In addition, we are running out of DHCP available DHCP addresses. I need to have a solution that will give me more available IP's, but reduce our broadcast domain.
We are Cisco VoIP shop. Our current environment consists of dual 6509 chassis in a VSS config. We have 10 access switches that are model 3750's. Each 3750 has dual 1Gb fiber links to the VSS Core in an etherchannel configuration. We have 2 VLANS (data and voice) that spread throughout every switch. Both VLAN's have their own DHCP scope.
Our current broadcast domain is a 255.255.248.0, so we have over 2000 potential broadcast devices. Cisco recommends not having larger than 512. So my research has brought me to a design as follows:
MY DESIGN:
> Have individual voice and data VLANs for each closet switch.
> We have 10 closet switches so this would require 20 new vlans
> With every separate VLAN we would need a different DHCP scope.
> Configure 20 new DHCP scopes for the 20 new VLANs.
> Each DHCP scope would have a 512 available addresses.
> Enable IP Routing and configure EIGRP on the VSS Core and 3750's.
> I'm tossing around the idea of have each 3750 be an EIGRP Stub. Not sure yet.
QUESTIONS:
1. How to verify what I described in my design?
2. Any alternative solution that might be less complicated than configuring Layer 3 on all my access switches?
3. Any thoughts on configuring EIGRP Stub vs. having the VSS Core do all the work?
4: Any template that I could base my 3750 config from?
View 6 Replies
View Related
Nov 14, 2011
For some unknown reason our NMS cannot validate SNMP string configured on catalyst switch 4507. SNMP version is 2c
snmp-server community Cisco RO
snmp-server community Cisco RW
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps entity
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps config
snmp-server enable traps hsrp
snmp-server enable traps syslog
There is Reach ability between NMS server and switch but snmp string is not validating.
View 2 Replies
View Related
Feb 7, 2012
Is there a way I can find out the amount of bandwidth i'm using on a particular interface on a 4507 cisco multi-layer switch? It is a gig port and I have it setup for monitoring (spanning) and I see packets being dropped in the "Total Output Drops" area. To me it looks like it must be exceeding the 1gig limit but I don't know a way to check to make sure. I also have the queueing strategy set to FIFO.
View 3 Replies
View Related
Nov 8, 2011
I have a 4507 cisco switch loaded with two sup-modules.. [code]
View 5 Replies
View Related
Jan 30, 2013
We have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies
View Related
Sep 4, 2012
i have a problem with a cisco cat. 4507 edge switch as when i have a login ssh session to the switch the supervisor engine restart and the redundant Sup. engine becomes the active and so on this problem mainly happen when i have multible SSH session to the switch and it happened very rarely with a single ssh login
the ios version i use is cat4500-entservicesk9-mz.122-54.SG which im using on all my edge switch and they are all working fine excpt this one
View 1 Replies
View Related
Mar 8, 2013
I have Catalyst 4507 R-E with one supersor engine n 3 other modules.My question is related to routing of different networks through this switch.I already have certain routes configured which are going to my ISP thru Juniper firewall.(192.168.0.9)I also have Cisco ASA 5510 which i want to use as a backup in case the first one goes down.
View 3 Replies
View Related
Jul 29, 2012
I have been trying to reset my Cisco 4507 R-E with sup 10GE engines, and I am not having any luck. I have followed the following document:
[URL]
I have tried "wr erase" and "erase startup-config." I cannot delete the vlan.dat file either. I am using the command "erase cat4000_flash:vlan.dat" and its not working either. I have done these commands several times with no success. When asked if I want to save the config changes, I am answering with a "no" I have not tried to depress the small "reset" button on the front of the sup engines as I read that this just restarts the switch.
View 2 Replies
View Related
Apr 24, 2012
I have this cisco 4507 switch that I need to configure multiple ip ranges on. The problem is that I can only configure two ip ranges on it, one ip range on the management vlan and the other ip range on vlan 2. After I have configured these 2 vlans with different ip ranges, I can route between then and get them to talk to each other, but that is all I can do. If I add another vlan with a different IP range I cannot see it from the switch or get any of the otehr ip ranges to see it.
I am doing something dumb because this is a layer 4 device so it should be able to route the ip ranges. I have tried everything just cannot get it to work. I have assigned the IP range directly to the port number and directly to the vlans. Just wont work.
View 6 Replies
View Related
Mar 5, 2013
Would like to ask whats the correct snmp config so that it will send to our snmp server when a mac flapping occurs on a cisco switch specifically 4507 switches.
View 6 Replies
View Related
Mar 19, 2012
working first time on switch 4507 , this is my 2nd week and i plug the console on this 4507 switch , the switch reboots automatically it comes to stage mention below and reboots. My question is i have not seen any error message on this switch and it reboots automatically so what is the problem.
* *
* Welcome to Rom Monitor for WS-X4013+ System. *
* Copyright (c) 1999-2003 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.1(20r)EW1
Supervisor: WS-X4013+ Chassis: WS-C4507
[code]...
View 5 Replies
View Related
May 22, 2013
I am having an issue where MAC addresses from my user PC's are registering on different ports than the ones they are plugged in to. I have my PC's plugged in to my Cisco phones (most of which are 7941's), and then patched back to my switch, (4507 or 4006). The issue is that a user will be working fine, they will have both their PC and Phone MAC's registered on the correct prot and then with out intervention the PC MAC addresses will register itself with another physical port and the user will pull a 169.x.x.x address and have not access to the network. This is happening to multiple users all of which are hardwired. Port security is configured to allow 3 MAC's, obviously if I change that to 2 it will not allow an incorrect MAC's to register with that port, but I would like to know why this is happening. Both the 4507 and 4006 have been up for 1 year and 33 weeks. The fix has been to find out where their MAC has registered it self, unplugg that PC from the phone, and let the port security aging time (2min) clear all MAC's from the port.
View 3 Replies
View Related
Mar 3, 2013
We have ordered a new 4507 chasis with a supervisor engine.We have also ordered a spare supervisor engine.As per Cisco documentation WS-X45-SUP7L-E is shipped with a default IP base license.My question is that is this a e-delivery or a paper base license.The Cisco documentation also states that we can use the same license to upgrade both the redundant and active supervisor from lan base to IP base.
View 2 Replies
View Related
Aug 19, 2012
We are facing issue of high Latency and slowness with Switch Cisco 4507R at the Customer site.show logging for the Switch and if there is any IOS related issue [BUG] or some other finding for this case.
View 1 Replies
View Related
Oct 31, 2011
I have catalys 4507 with TWO supervisor V.I flowed this procedure : url...
after the reset normaly i can change the password and i check the confreg is 0X2142 but it still ask to enter the possword should i remove 1 supervisor and do the procedure or i must let the two spuervisor?
View 2 Replies
View Related
