Cisco Switching/Routing :: 4507 Not Able To Route Multiple Ip Ranges
Apr 24, 2012
I have this cisco 4507 switch that I need to configure multiple ip ranges on. The problem is that I can only configure two ip ranges on it, one ip range on the management vlan and the other ip range on vlan 2. After I have configured these 2 vlans with different ip ranges, I can route between then and get them to talk to each other, but that is all I can do. If I add another vlan with a different IP range I cannot see it from the switch or get any of the otehr ip ranges to see it.
I am doing something dumb because this is a layer 4 device so it should be able to route the ip ranges. I have tried everything just cannot get it to work. I have assigned the IP range directly to the port number and directly to the vlans. Just wont work.
View 6 Replies
ADVERTISEMENT
Feb 12, 2012
i want to create a trunk between 4507 & 3945E router & route two vlans from router 3945E
4507# vlan 99 & 51
# int vlan 99
# ip add 10.22.100.1/24
#int vlan 51
# ip add 10.22.103.1/24
[code].....
4507 version : IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
3945E: 15.1(2)T4 what I am missing?
View 3 Replies
View Related
Jan 23, 2013
I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
View 5 Replies
View Related
Jan 2, 2013
I feel like this has probably been asked a thousand times over, but it doesn't seem to work for me. TCP works fine. I can't find any definitive answers, I'm still a novice with the IOS.
The purpose behind opening the ranges of UDP ports to the interface and forwarding is because the people in question want to run a VOIP phone from their home, but they have a home grade Internet connection, so therefore no static IP. Also, they're not going to pay for a router to create a S2S VPN.
Also, from one of the remote sites for which there is a VPN ( the 192.168.6.X/24 site), the audio is only one way. The phone guy says "i need to open ports both way through the VPN), but I feel like that's already been done??
For my other site ( 192.168.15.0/24 ) I have an IPSEC over GRE tunnel going, I don't know about the status of the voice phone there..or if its even made it there
Here's my config...i'm redacting things like public IP's, VPN keys, and the like
#show run
Building configuration...
Current configuration : 6525 bytes
!
! Last configuration change at 14:51:00 EST Wed Jan 2 2013 by ctouch
! NVRAM config last updated at 14:57:46 EST Wed Jan 2 2013 by ctouch
[Code]...
View 4 Replies
View Related
Feb 4, 2013
I have an ASA5510, and site-to-site VPN with several remote clients. I have to add another client but their network range overlaps an existing tunnel. Both are using 172.16.0.0/16. I would like to 1-to-1 NAT them as 172.17.0.0/16.
Is it possible to perform the NAT on my device, post-decryption, or is it necessary that I have them perform the NAT at their end?
View 2 Replies
View Related
Aug 2, 2012
I have a client that needs a VPN with multiple network address ranges on the far end of the IPSEC tunnel. Is this possible with this RV180 unit?
View 1 Replies
View Related
Jul 24, 2012
Any explanation regarding these different operating temperature ranges? I would think it doesn't matter the enclosure that the switch is in, it will either work or fail at a certain temperature.,-40C to +70C (Vented Enclosure Operating),-20C to +60C (Sealed Enclosure Operating), -34C to +75C (Fan or Blower equipped Enclosure Operating).
View 0 Replies
View Related
Jan 21, 2013
2 ISP's connected to a 4507, both with seperate public IP blocks. Based on some source IP addresses on the LAN they would either use ISP-A or ISB-B's connection based on what I define.
View 3 Replies
View Related
Feb 16, 2012
Any "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies
View Related
Feb 14, 2012
How do I enable SSH on 4507. I do not see "ip ssh ..." commands config#ip ssh (I do not see "ip ssh " commnd)
Do i need to enable something else?
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
View 1 Replies
View Related
Nov 19, 2012
I am having a Cisco 4507 switch. The CPU on the switch is running between 50% to 60% constantly. To troubleshoot I collected some logs using debugs & show commands.
debug platform packet all receive buffer
show platform cpu packet buffered
debug platform packet all count
show platform cpu packet statistics
show processes cpu sorted | exc 0.00
show platform health
show platform cpu packet statistics
show platform health output shows the below process crossing the target value.
%CPU %CPU RunTimeMax Priority Average %CPU Total
Target Actual Target Actual Fg Bg 5Sec Min Hour CPU
Stub-JobEventSchedul 10.00 13.41 10 47 100 500 13 13 10 5462:52
K2PortMan Review 3.00 5.35 15 11 100 500 4 4 3 1799:47
What I need to know is, though these process are running in Low Priority, will there be any issue if the CPU goes high due to these process.
View 1 Replies
View Related
Jun 4, 2012
Could not find a valid file in BOOT environment variable. BOOT variable can be set from IOS. To find currently setRom Monitor variables, type 'set' command.
Choosing a boot method, type 'confreg' command.rommon 1
>setPS1=rommon ! >RommonVer=15.0(1r)SG5SupportedFeatures=1ConsecPostPassedCnt=2DiagMonitorAction=NormalCONFIG_FILE=bootflash:cat4500e-
[Code].....
View 11 Replies
View Related
Jun 13, 2012
Our organization currently has a Cisco 4507 acting as our core switch and 2 ASA525 firewalls.
Our existing ISP runs into our 4507. Here is the port config.
interface GigabitEthernet7/1
description ISP-DSL
switchport access vlan 10
[Code].....
We have recently purchased a 5Mbit line with a second ISP and will have the line activated tomorrow. In addition, we recently obtained our AS number through ARIN. How would I configure the second ISP to be used for load balancing/failover?
View 8 Replies
View Related
Sep 10, 2012
4507 Went To Romon During IOS upgrade.
View 3 Replies
View Related
Apr 26, 2012
We will deploy several 4507 with 2xsup7 as a L2 access switches for our office.Does LAN_Base IOS version support SSO or we need purchase IP_Base IOS (L3)?
View 1 Replies
View Related
Nov 29, 2012
SSH has been enabled on our one and only 4507 switch for several months and working fine. A few weeks ago the switch had to be reloaded and when it was back online I couldn't SSH to it. When I connected via the console and typed "show ip ssh" it came back saying I needed to generate the keys. Did that and it starting working again. The same switch had to turned off and on the other day due to a power down in the server room and when it came back the same thing happened again!!
The version of IOS is: cat4000-i5k91s-mz.122.20.EW
View 1 Replies
View Related
Nov 8, 2012
Is there any option to configure cisco 4507 to genrate log alert when cpu utilization or port utilization reaches above certain percentage.
View 2 Replies
View Related
Nov 29, 2011
I need to configure a port channel between two sw 4507R. with port Giga, but those port are in different modules.
Sw-1
interface GigabitEthernet5/48
description **** Conexion Switch-2*****
[Code].....
View 2 Replies
View Related
May 13, 2013
I have 4507 switch and I got the error of fan sensor which is mention below [code] What the meaning of FAN Sensor both are Bad/off ?
View 4 Replies
View Related
Aug 25, 2012
QoS design problem that I have. I have a client that is deploying new 4507 series switches with SUP6Es. The client will be running lots of voice, streaming video, and video conferencing over the LAN and want to base QoS on Cisco Media net recommendations.
I need to design a new QoS policy with focus on the above media services with basic queuing for critical data services. I have read the Media net design guide and the suggested 12-class model will be too complex to start with but I have seen references to start with a 8-class model with the ability to easily migrate to 12-class in the future. The 8-class model meets all of our requirements but I need to understand how this will work with the 4507 queuing model? [URL]
View 1 Replies
View Related
Jan 19, 2012
we have a core switch 4507RE at the data center and 2 departments that connect to it via 10Gig fiber using X2-LRM modules. Each department has a 3 switch stack and both locations are identical w.r.t type and setup scenario.the stack comprises of 1 x 3750E and 2 x 3750G . uplink is from X2 port tengig3/0/1 from the 3750E switch.
All of a sudden dept B started facing problem , where the ping would break and throughput comes around 6 - 7 mbps from that dept to the server behind the core switch. we also noted CRC error on both sides preodically.
we replaced the multimode fiber patch cords, re did the splicing , which stopped the CRC errors to appear.now since morning the uplink port on the 3750E (3/0/1) would suddenly be in "down" state with (err-disabled) as the status when i run sh int ten 3/0/1
and i can also see CRC errors and input errors on the same interface.. if i do shut / no shut .. the port is up and active again.. but this has happned 3 times today.the core swith side is still OK and no CRC / input / output errors are seen..
now on the 3750E i have swapped the 10gig module from 3/0/1 to 3/0/2 . the port is still up but i can see 400 CRC and 500 Input errrors.the module is also OK as i had replaced it with dept 1's module.
View 1 Replies
View Related
Nov 14, 2011
For some unknown reason our NMS cannot validate SNMP string configured on catalyst switch 4507. SNMP version is 2c
snmp-server community Cisco RO
snmp-server community Cisco RW
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps entity
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps config
snmp-server enable traps hsrp
snmp-server enable traps syslog
There is Reach ability between NMS server and switch but snmp string is not validating.
View 2 Replies
View Related
Feb 7, 2012
Is there a way I can find out the amount of bandwidth i'm using on a particular interface on a 4507 cisco multi-layer switch? It is a gig port and I have it setup for monitoring (spanning) and I see packets being dropped in the "Total Output Drops" area. To me it looks like it must be exceeding the 1gig limit but I don't know a way to check to make sure. I also have the queueing strategy set to FIFO.
View 3 Replies
View Related
Nov 8, 2011
I have a 4507 cisco switch loaded with two sup-modules.. [code]
View 5 Replies
View Related
Jan 30, 2013
We have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies
View Related
Sep 4, 2012
i have a problem with a cisco cat. 4507 edge switch as when i have a login ssh session to the switch the supervisor engine restart and the redundant Sup. engine becomes the active and so on this problem mainly happen when i have multible SSH session to the switch and it happened very rarely with a single ssh login
the ios version i use is cat4500-entservicesk9-mz.122-54.SG which im using on all my edge switch and they are all working fine excpt this one
View 1 Replies
View Related
Mar 8, 2013
I have Catalyst 4507 R-E with one supersor engine n 3 other modules.My question is related to routing of different networks through this switch.I already have certain routes configured which are going to my ISP thru Juniper firewall.(192.168.0.9)I also have Cisco ASA 5510 which i want to use as a backup in case the first one goes down.
View 3 Replies
View Related
Jul 29, 2012
I have been trying to reset my Cisco 4507 R-E with sup 10GE engines, and I am not having any luck. I have followed the following document:
[URL]
I have tried "wr erase" and "erase startup-config." I cannot delete the vlan.dat file either. I am using the command "erase cat4000_flash:vlan.dat" and its not working either. I have done these commands several times with no success. When asked if I want to save the config changes, I am answering with a "no" I have not tried to depress the small "reset" button on the front of the sup engines as I read that this just restarts the switch.
View 2 Replies
View Related
Mar 5, 2013
Would like to ask whats the correct snmp config so that it will send to our snmp server when a mac flapping occurs on a cisco switch specifically 4507 switches.
View 6 Replies
View Related
Mar 19, 2012
working first time on switch 4507 , this is my 2nd week and i plug the console on this 4507 switch , the switch reboots automatically it comes to stage mention below and reboots. My question is i have not seen any error message on this switch and it reboots automatically so what is the problem.
* *
* Welcome to Rom Monitor for WS-X4013+ System. *
* Copyright (c) 1999-2003 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.1(20r)EW1
Supervisor: WS-X4013+ Chassis: WS-C4507
[code]...
View 5 Replies
View Related
May 22, 2013
I am having an issue where MAC addresses from my user PC's are registering on different ports than the ones they are plugged in to. I have my PC's plugged in to my Cisco phones (most of which are 7941's), and then patched back to my switch, (4507 or 4006). The issue is that a user will be working fine, they will have both their PC and Phone MAC's registered on the correct prot and then with out intervention the PC MAC addresses will register itself with another physical port and the user will pull a 169.x.x.x address and have not access to the network. This is happening to multiple users all of which are hardwired. Port security is configured to allow 3 MAC's, obviously if I change that to 2 it will not allow an incorrect MAC's to register with that port, but I would like to know why this is happening. Both the 4507 and 4006 have been up for 1 year and 33 weeks. The fix has been to find out where their MAC has registered it self, unplugg that PC from the phone, and let the port security aging time (2min) clear all MAC's from the port.
View 3 Replies
View Related
Mar 3, 2013
We have ordered a new 4507 chasis with a supervisor engine.We have also ordered a spare supervisor engine.As per Cisco documentation WS-X45-SUP7L-E is shipped with a default IP base license.My question is that is this a e-delivery or a paper base license.The Cisco documentation also states that we can use the same license to upgrade both the redundant and active supervisor from lan base to IP base.
View 2 Replies
View Related
Aug 19, 2012
We are facing issue of high Latency and slowness with Switch Cisco 4507R at the Customer site.show logging for the Switch and if there is any IOS related issue [BUG] or some other finding for this case.
View 1 Replies
View Related
