Any explanation regarding these different operating temperature ranges? I would think it doesn't matter the enclosure that the switch is in, it will either work or fail at a certain temperature.,-40C to +70C (Vented Enclosure Operating),-20C to +60C (Sealed Enclosure Operating), -34C to +75C (Fan or Blower equipped Enclosure Operating).
View 0 RepliesHave a potential customer that is looking at the IE2000 series switch and at the Rockwell Allen Bradley switch
Question is does it support Device Level Ring (DLR) capability. I do not see this specifically mentioned in the Data Sheets but it talks about a
Resilient Ethernet Protocol (REP) and I am wondering if this is the same thing?
Can we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies View RelatedI am trying to get the temperature reading from one of our 3560G Switches using SNMP. When I run an snmpget on the Switch it returns back to me a "1".
So when I run the following I get:
> snmpget -v1 -c public 192.168.x.xxx 1.3.6.1.4.1.9.9.13.1.3.1.3.1005
SNMPv2-SMI::enterprises.9.9.13.1.3.1.3.1005 = Gauge32: 1
But when I telnet to the device and run a "show env temperature status" I get:
# show env temp status
Temperature Value: 32 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 51 Degree Celsius
Red Threshold : 61 Degree Celsius
So I'm not sure why I am getting a "1" when using snmpget on the OID 1.3.6.1.4.1.9.9.13.1.3.1.3.1005 which is (ciscoEnvMonTemperatureStatusValue)??
If I run the same OID on another 3560G Router I get the correct output from snmp....
I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
I feel like this has probably been asked a thousand times over, but it doesn't seem to work for me. TCP works fine. I can't find any definitive answers, I'm still a novice with the IOS.
The purpose behind opening the ranges of UDP ports to the interface and forwarding is because the people in question want to run a VOIP phone from their home, but they have a home grade Internet connection, so therefore no static IP. Also, they're not going to pay for a router to create a S2S VPN.
Also, from one of the remote sites for which there is a VPN ( the 192.168.6.X/24 site), the audio is only one way. The phone guy says "i need to open ports both way through the VPN), but I feel like that's already been done??
For my other site ( 192.168.15.0/24 ) I have an IPSEC over GRE tunnel going, I don't know about the status of the voice phone there..or if its even made it there
Here's my config...i'm redacting things like public IP's, VPN keys, and the like
#show run
Building configuration...
Current configuration : 6525 bytes
!
! Last configuration change at 14:51:00 EST Wed Jan 2 2013 by ctouch
! NVRAM config last updated at 14:57:46 EST Wed Jan 2 2013 by ctouch
[Code]...
I have this cisco 4507 switch that I need to configure multiple ip ranges on. The problem is that I can only configure two ip ranges on it, one ip range on the management vlan and the other ip range on vlan 2. After I have configured these 2 vlans with different ip ranges, I can route between then and get them to talk to each other, but that is all I can do. If I add another vlan with a different IP range I cannot see it from the switch or get any of the otehr ip ranges to see it.
I am doing something dumb because this is a layer 4 device so it should be able to route the ip ranges. I have tried everything just cannot get it to work. I have assigned the IP range directly to the port number and directly to the vlans. Just wont work.
What is the difference between Operating temperatue & storage temperature of switch C3560E ?
View 2 Replies View Relatedi need a software for webstar 2000 for windows 7
View 1 Replies View RelatedI need to know how is the ambient temperature for the Nexus 7000 switches to plan a new datacenter. In the datasheet I found the following information regarding this topic:"GR-63-CORE Network Equipment Building Standards (NEBS) specification published by Telcordia Technologies in Section 4.1.2". How are the specification for temperature in this standard?
View 1 Replies View RelatedI have an issue with one of our switches, switch model WS-C2960-24TC-L, i am not able to display switch temperature as below,
Switch#sh verCisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 15.0(2)SE2, RELEASE SOFTWARE (fc1)Technical Support: URL ) 1986-2013 by Cisco Systems, Inc.Compiled Tue 05-Feb-13 12:41 by prod_rel_team(code)
Our LMS DCR include more then 1200 devices, ( ASR 1000, CISCO 2600, 2800 advanced ip services IOS etc. )Everything is working well except the IP SLA device table is empty.I can not choose any device from this table.How can i import/add devices to this table/database automatically ?
View 2 Replies View RelatedBelow module showing inlet and outlet temperature N/o.How to find the issue related to sensor in the module or something else to troubleshoot in the module to find the issue.
View 5 Replies View RelatedWe have a nexus 5k, and it kind of got hung today... it is running. Version 5.1(3)N2(1b) the reset reason shows.Power down due to temperature sensor policy trigger.It doesn't look documented. What policy is it referring to? not sure if this is an IOS bug ?
View 1 Replies View Relatedwe have two 6509E which are configured in VSS mode with the following modules in each:
1 48 CEF720 48 port 10/100/1000mb Ethernet
2 8 DCEF2T 8 port 10GE
3 4 CEF720 4 port 10-Gigabit Ethernet
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G
I need to know if the temperature of the attached modules are normal or there is a problem?
the status of one of the supervisor engines is "MajFail" as shown below:
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
5 Major Error
if vPC is supported between a single 2232PP FEX and two 7000 switches running 6.0(1)? I have been researching this for an implementation I am doing for a client and was able to determine it was not supported with earlier versions of 5.0 when the FEX is connected via vPC as I described above, but I can't find anything related to version 6.0(1). I have done this for other clients with 5000 and 2000 switches, but I don't have too much experience with 7000 switches.
View 5 Replies View RelatedI have a big doubt. Can I connect a LAN switch (i.e. 2960, 3560 or 3750) to a couple of Nexus 2000 FEX (i.e 2232P or 2248TP) and have a Port-Channel or vPC with STP active and several VLANs through this Port-Channel? Or Can I only connect servers to these N2K FEX?
View 3 Replies View RelatedIf the latest release of NX-OS 6.1.2 supports dual homing a Nexus 2000 to a pair of Nexus 7000s (F2 Module)? The document does state something about support for vPC+ but is not really clear about it.
View 4 Replies View RelatedMy company is doing an nationwide upgrade of it's leased 2951 routers. For security sake I need to wipe everyone of them before being sending them back to the leasing company. I would like to somehow boot to a USB drive and call it a day.
View 4 Replies View Relatednyone know if "vpc-orphan-port suspend" works if i put on N2k interface. not the fex link. example i have fex 101 and i put on eth 101/1/10 will it suspend the port on N2K connected to secondary N5K when peer link is down?
View 2 Replies View Relatedis it possible to connect one Cisco Nexus 2000 fabric extender to two Cisco Nexus 5000 and use one link on the first side and two links on the other side?
View 3 Replies View Relatedcurrently nexus 2000 and nexus 7000 does not support dual connection. you can not connect to 1 nexus 2000 to 2 nexus 7000 chasis. But for the nexus 5000, Nexus 7000s? 5000s and 7000s run same software.
View 1 Replies View RelatedI have several SGE2000 in production and every night I save the current configuration to a tftf server... from time to time I get the following error: [code] Can't open TFTP client.At this time, the only way to be able to save the config again is rebooting the switch, but this is not a solution I am comfort.
View 5 Replies View RelatedI want to know OID value for 'Chasis Temperature sensor' of C4948E.as below, I could find it for C4948 but couldn't C4948E and C4948E-F.
======================================== C4948-10G ======================================================
mrtg@WWW:~$ snmpwalk -v 2c -c public X.X.XX 1.3.6.1.2.1.47.1.1.1.1.2
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1 = STRING: "Cisco Systems, Inc. WS-C4948-10GE 1 slot switch "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2 = STRING: "WS-C4948-10GE 1 slot switch chassis slot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.3 = STRING: "Chassis Temperature Sensor"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4 = STRING: "Container of Fan Tray"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5 = STRING: "FanTray"
[code]...
I am designing a network for my client where I have to implement a 10 Gig end to end connectivity. The major factor of concern from my management is about scalability (space to include more 10Gig servers as the nodes grow up). I have suggested Cisco 5596UP with 2232 PP as this gives ample amount of 10Gig ports. The setup has to be implemented across 2 different datacenters located 40 Kms apart, connected with 10Gig DC Interconnect.
I understand that Cisco Nexus 2232 is a Layer 2 Only switch and would need to communicate with parent 5K switch very frequently. Is it necessary to have the 2K and 5K pair in the same datacenter or in proximity? Is it possible to have the SFP uplinks connected to the DC interconnect? Because we have two datacenters located 40 Kms apart and having 1*Layer 3 - 5K switch at DC A with Layer 2 - 2K nexus Switch at DC B will be cost effective. We do require more 10Gig ports and not much requirement on Layer 3 usage. What are the type of communication that would be much frequent between 2K and 5K?
Does the LACP will be supported on Nexus 2000 host interfaces when parent switch is Nexus 7000?
View 5 Replies View RelatedI curently have 2 Data centers connected with a Metro Ethernet Connection. Each Data Center has 6500 with Sup720s. The Metro Ethernet connection is currently conected by a L3 routed interface. I now need to enable VRFs between the locations and want to determine the best way to adjust the Mero. I was considering adjusting the routed interface to use Ethernet sub-interfaces. Each VRF would be given a different subinterface over the Metro Ethernet connection. I have done this on internal LAN connections but am concerned about exteding across data centers over Metro E.
View 1 Replies View RelatedI have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedI have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
Any info on how to configure dynamic-pinning, instead of static pinning on a Nexus 2224 connected to a 7009?Can't seem to find anything on CCO!
View 9 Replies View RelatedI'm just setting up a Cisco rv180w router to replace our aging Belkin. I need to allow a range of ports through the firewall to a particular PC on our internal network that runs our VOIP/SIP Trunk phone system.
The Cisco's Port Forwarding looks like it can only forward one port at a time, but for our phones I need to allow a full range of ports (in this case ports 49152-64512) to one machine at 192.168.x.xx.
On the Belkin I used something called 'Virtual Servers' which allows you to enter ranges of ports. Anybody know what the equivalent might be for the Cisco router?
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI have peculiar challenge ahead of me and would like to get new perspectives.
The objective is to route specific VLAN traffic and the caveat is that I have multiple VLANs with the same network address.
For example:
VLAN100 10.10.10.0/28 VLAN101 10.10.11.0/28 VLAN102 10.10.12.0/28
VLAN103 10.10.12.0/28
VLAN104 10.10.11.0/28
I need traffic going from VLAN100 with a destination of 10.10.11.0 forwarded to VLAN101 and NOT VLAN104.
This task is currently being completed by a multi context firewall and we're trying to decommission the asset.