Cisco Routers :: RV180 VPN With Multiple Network Address Ranges
Aug 2, 2012I have a client that needs a VPN with multiple network address ranges on the far end of the IPSEC tunnel. Is this possible with this RV180 unit?
View 1 Replies
ADVERTISEMENT
Cisco WAN :: ASA5510 - Multiple L2L VPN With Overlapping Remote Network Ranges?
Feb 4, 2013I have an ASA5510, and site-to-site VPN with several remote clients. I have to add another client but their network range overlaps an existing tunnel. Both are using 172.16.0.0/16. I would like to 1-to-1 NAT them as 172.17.0.0/16.
Is it possible to perform the NAT on my device, post-decryption, or is it necessary that I have them perform the NAT at their end?
Cisco Routers :: RV180 Multiple Tunnels To The Same Endpoint?
Nov 10, 2012I purchased the RV180 to replace a dead Linksys BEFVP41 to connect a home office to HQ. The Linksys was configured with three IPSEC tunnels to connect to three different subnets all through the main HQ gateway. Note that each tunnel is independent with its own pre-shared key. I can configure the same tunnels on the RV180, and each one works correctly, but I can only get one to run at a time. I have to disable the other two. Enabling a second tunnel results in the No phase2 handle found error. I could not use the Basic VPN setup as it complains that the remote endpoint is already in use. I had to use the Advanced VPN Setup to create the IKE and IPSEC policies. In a different discussion [URL]
View 3 Replies View RelatedCisco Routers :: RV180 / Setup Custom Service That Contains Both Multiple Disjoint Ports?
Jul 11, 2012I have an rv180 and I'm trying to setup a custom service that contains both multiple disjoint ports (some UDP some TCP), as well as a TCP port range. This has lead me to a couple of questions.1) Is it even possible to have a single custom service with disjoint ports? Is it just going to be necessary to define multiple partial services for this?2) Is it possible to forward a range of ports? It's clear how to define a service with a port range, but the port forwarding table interface only allows me to select one LAN-side port for any service. Is there a secret notation that I need to do here that will just forward to the same LAN-side port as the WAN-side port---effectively one-to-one NAT forwarding, but just for the selected service?
View 8 Replies View RelatedCisco Routers :: RV180 / RV180W - MAC Address Filtering And IP Biding
May 24, 2012I'm interested by the router Cisco RV180 or RV180W.
So as to increase security, i would like to set a MAC adress access restriction for all peripherals that would be connected to the router (10 computers, 2 servers, 6 Synology NAS) : only allowed MAC adress should access to the internet and network ressources.
Does the Cisco RV180 or RV180W have an IP to Mac biding feature and a Mac adress restriction feature ? If yes, how many peripherals/computers can be set ?
For example, only 30 mac/IP adress can be allowed on my actual router and it is not enough.
Cisco Switching/Routing :: 4507 Not Able To Route Multiple Ip Ranges
Apr 24, 2012I have this cisco 4507 switch that I need to configure multiple ip ranges on. The problem is that I can only configure two ip ranges on it, one ip range on the management vlan and the other ip range on vlan 2. After I have configured these 2 vlans with different ip ranges, I can route between then and get them to talk to each other, but that is all I can do. If I add another vlan with a different IP range I cannot see it from the switch or get any of the otehr ip ranges to see it.
I am doing something dumb because this is a layer 4 device so it should be able to route the ip ranges. I have tried everything just cannot get it to work. I have assigned the IP range directly to the port number and directly to the vlans. Just wont work.
Connect Two Different IP Address Ranges Without Router?
Mar 22, 2012Is there anyway to connect two different IP address ranges without setting up vlans? Trying to setup something so I can test out a device that uses "BACnet Broadcast Management Device" and I dont have two switches to create a vlan.
On site they have a couple of ranges setup with vlans
A 10.169.51.xx 255.255.255.0
B 10.169.52.xx 255.255.255.0
C 10.169.53.xx 255.255.255.0
D 10.169.54.xx 255.255.255.0
Cisco Wireless :: Make WAP4410 Fall Under Two Ip Address Ranges?
Apr 24, 2011I am wondering if I can make our WAP4410 fall under two ip address ranges. I want to have a network for the office users and one for the guest users. We currently use a Safe@Office500WP Checkpoint router. It allows us to create multiple network ranges. We have the office users wireless under 192.168.0.1 ip range and the Guest Wireless is under the 192.168.200.1 range. Do I need two access points or can this be done with just the one?
View 7 Replies View RelatedCisco Routers :: RV180 Use VLAN1 For Internal Private Network
Sep 7, 2012My plan is to use VLAN1 for the internal private network and VLAN2 for free public wifi. My question is can I use a PC on VLAN1 to configure/manage my access points? There are no dedicated PCs on VLAN2.
View 7 Replies View RelatedCisco VPN :: Multiple Types On RV180?
Aug 30, 2012I need to connect three sites. I also need to support some roving PCs connecting to the sites via VPN. With the RV180, can I support multiple ptp vpn connects between them, and at the same time, have the roving PCs connect to the RV180s.
View 0 Replies View RelatedCisco Switching/Routing :: NAT Multiple External IPs On RV180?
Dec 25, 2012how to properly route multiple external IPs to internal ips assigned to several servers. Where I'm getting a bit lost is that I have two levels of routing - one from the outside into a comcast business class cable modem, which also creates its own internal network. Within that internal network, I have my RV180 router, which creates another separate internal network in which the servers live (don't want the servers to have access to other computers within the Comcast Modem's internal network). I want to map the external ips to servers within the RV180 second level network.
To diagram:
Comcast Cable Modem
/
RV180 Computer(s)
/
S1 S2
An internal IP is assigned to the RV180 router. Suppose it is 192.168.1.100.
The cable modem itself supports NAT as well. Do I use NAT twice (on both cable modem and RV180) to route the external IP to S1 and S2?
Or do I modify the routing table on the cable modem? Then use One to One NAT on the RV180 to map the external IPs directly to the internals?
Home Network :: Belkin F5D8635-4v1 - Access Multiple Servers From One Dynamic IP Address
Jan 23, 2012I am working with MS Windows 2008 R2 and a Belkin F5D8635-4v1 router.
I have already set up a dynamic IP address which points to my router at home. In my home network I have multiple PC's that I would like to access from the internet. I would like to achieve this without needing to change my port forwarding rules on my router each time...
My thoughts are that I use a single dynamic IP address pointed to my router. My router then forwards to a server with some sort of software that can then forward to the correct PC based on the host name.
So I have 3 domains set up all pointing to the router's IP address:
dest1.domain.com -> 41.xxx.xxx.45
dest2.domain.com -> 41.xxx.xxx.45
dest3.domain.com -> 41.xxx.xxx.45
The router is not smart enough to redirect by host name, so it will just forward everything to 10.0.0.20 The server based at 10.0.0.20 must then have software to now redetermine the target based on the host name. The rules would be set up as follows:
dest1.domain.com -> 10.0.0.22
dest2.domain.com -> 10.0.0.24
dest3.domain.com -> 10.0.0.26
Getting Multiple Routers And All PCs On Same Network?
Jul 6, 2012I want the following configuration:
- 1 Master router with no PC's connected (only the slave routers will connect to it)
- 2 Slave routers each connected to master router Each slave router will have multiple PC's connected via ethernet and/or wireless
I have been able to set this up with all PC's having an internet connection. BUT I need all the PC's to see each other on a single network. I can see all the PC's on a single slave router but I can't see the PC's on slave 1 from slave 2 or vice versa. I have been using the WAN inputs on both slave routers. All 3 routers are Netgear WRN3500L.
Home Network With Multiple Routers
Dec 31, 2011I have a 2 wire HomePortal 1000SW modem in our home office. Its connected to a dlink DI-524 wireless router (also in the office), which is connected to a dlink DIR-601 in the opposite end of the house, both are connected using LAN ports, not WAN. All 3 of these devices are capable of wireless, and all have the same SSID and wep encryption key (they use different channels, 1, 6, 11). As of right now, i have the DI-524's wireless disabled, and the wireless is still on for the DIR-601 and the HomePortal, but only the HomePortal has DHCP turned on. The problem I'm having is that i can connect and get assigned an ip address when I'm in the office, but if i initially connect to the network near the DIR-601, i get limited connectivity and a self-assigned IP-address.
View 3 Replies View RelatedNetwork Multiple Routers - IP Conflict?
Mar 7, 2011I have two Netgear routers (N150 and DG834) and want to set them up so that in my office (external to the house) I have wired internet connection and in the house wireless, the office is too far away to run the wireless for the house there. The router in the office is connected to the ADSL line with the router in the house connected to it via a network cable.?I have disabled wireless on the office router however when i try to run both routers together I get an IP Address Conflict, I know I need to change the IP address so that they don't conflict but when I have tried this it hasn't worked and I have had to reset the router to the able to access it.
View 1 Replies View RelatedUsing Multiple Routers Without Significantly Reducing Network Speed
Aug 23, 2011I recently got a new modem/router device from my ISP and its wifi is fairly weak (no external antennas) especially in my basement. Since wifi is no longer an option and I only have one ethernet connection to my basement I was thinking of using my old router to distribute the one ethernet connection to multiple devices. Connecting my one ethernet connection to the old router, and its port#1 to my PC in the basement works without any meddling, but the speed has taken a significant hit. Before the second router I was getting ~30-40Mbps from my ISP. With the second router it is reduced to ~10-20Mbps. Both routers I assume are capable of at least 100Mbps (probably even 1Gbps?). The older router is a Linksys WRT54G which can do 54Mbps wirelessly so I assume it can exceed 10-20 wired.I tried giving the second router a static IP with DHCP off, but it did not seem to make a difference. I don't know if I set it up correctly, however. The modem/router uses 192.168.0.xxx while the second uses 192. 168. 1.xxx so I do not think there is any conflicts in the DHCP.
View 3 Replies View RelatedMultiple Wifi Routers On Network With Netgear Prosafe Vpn Firewall?
Mar 7, 2013They have a NETGEAR ProSafe VPN Firewall FVX538 on 192.168.1.1. They have 2 different wi-fi routers, one is static at 192.168.1.4, the other is not static.Someone donated a Linksys Wireless-B Broadband Router. They asked me to set that up. But i cannot get to the home page to change the IP address. 'multiple routers' it says to simply unplug one, so you can get to the config page at 192.168.1.1. I can not unplug the main router for the business, right? Do i need to change the IP of the Netgear temporarily? Will that bring down the network?
View 2 Replies View RelatedCisco Routers :: RV180 Ssh And Https From WAN?
Dec 23, 2012Is there any way to manage the RV180 from the WAN side via https and/or ssh?Also, is ssh from LAN even available?
View 3 Replies View RelatedCisco Routers :: RV180 VPN Does Not Work
Oct 18, 2012I have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.
View 6 Replies View RelatedCisco Routers :: Bug In RV180 Firmware V1.0
Jun 17, 2012I noticed if you add more than 10 access rules to the Access Rule table, you are unable to reorder past the first 10.Steps to reproduce:Create 11 rules of the same stream direction, outbound or inbound (...I found the bug with outbound, did not test inbound).try to reorder one of the first 10 rules to the end of the list, either by entering "11" manually, or by pressing the down arrow.System responds that "11" is an invalid number, or that the rule cannot be moved.This issue is not reported in the "Known Issues" section of the release notes for 1.0.1.9.
View 2 Replies View RelatedCisco Routers :: How To Connect OS X 10.7+ To RV180 VPN
Mar 2, 2013Which vpn client to use on os x ? (the one included in os x or another?) Which VPN configuration to use on RV180 ? and Which ports to open on RV180 Firewall ? (or any other parameters)
View 1 Replies View RelatedCisco Routers :: RV180 - Log Warnings With QOS IP Or MAC
May 20, 2013I had set up QOS for an IP Range and noticed the logs filling up with Warnings - hundreds within less than an hour.
I finally reset the router to factory and then step by step re-built my configuration - it was the QOS that started generating these warnings like:
Tue May 21 13:18:39 2013(GMT-0500) [rv180][Kernel][KERNEL] [87073.550000] IN=bdg1 OUT= DST MAC=d8:67:d9:c3:a0:2e SRC MAC=00:0e:58:58:57:7a PAYLOAD TYPE=08:00 SRC=192.168.1.193 DST=208.85.44.22 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=19313 DF PROTO=TCP SPT=1768 DPT=80 WINDOW=2534 RES=0x00 ACK URGP=0 MAR
[Code].....
In both cases above, after I started to suspect QOS, I entered a narrow IP range to test and then a MAC to test. Using a VLAN seems to work fine and generate no errors - even a VLAN for the same associated host(s).
I have a support case open about this - didn't get too far yet, but now with a better repro, maybe they will.
Cisco Routers :: RV180 What Are The Alternatives For Android ICS
Oct 30, 2012I currently have an RV180 in a small business set-up and curently being accessed remotely by laptops (Quick VPN) and Ipads/Android ICS tablets (PPTP). All is working well but I've become concerned about the security risks of PPTP and would like to shift the tablets to IPSec.
1) For a small business are the PPTP risks real?
2) What are the alternatives for Android ICS? I can't find a Quick VPN client for Android.
3) I can't get the core IPSec VPN in Android to connect to the RV180? Is this possible?
Cisco Routers :: NATed Did Not Add VLAN On RV180
May 7, 2013I have RV180 configured with two VLANs. First VLAN is untagged and second VLAN is tagged. The purpose is two have two subnets, with the second subnet used for guest access. Both VLANs have DHCP server enabled. First VLAN is 192.168.1.0/24 and the second VLAN is 192.168.2.0/24, When I connect a computer with untagged Ethernet interface, it gets an IP address from DHCP server on the first subnet i.e. 192.168.1.100 and it can successfully access Internet. When I connect a computer with tagged Ethernet interface (I am using VLAN ID 10), it gets an IP address from DHCP server on the second VLAN i.e. 192.168.2.100. So far so good. I can successfully ping hosts on the Internet i.e. ping www.google.com. But I cannot access Internet from the web browser. I captured Wireshark trace and here is what I see...
1. TCP SYN. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
2. TCP SYN ACK. Source IP A.B.C.D, destination IP 192.168.2.100. Ethernet frame has VLAN tag (VLAN ID 10)
3. TCP ACK. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
4. TCP Data. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
5. TCP Data. Source IP A.B.C.D, destination IP 192.168.2.100. Frame is untagged
The problem is at #5. Packet came back from the Web Server. RV180 properly NATed it to the local IP address. But it did not add VLAN tag.
Cisco Routers :: Rv180 Dropping LAN Connections?
Mar 13, 2013I just recieved a new RV180 yesterday and it will not connect to my switch. Router was updated to the newest firmware, reset to factory settings. I did change the ip and ip range. Router works fine with one computer attached direct. As soon as I connect my sf300-24P to it, the WAN and LAN lights all light up and then go out. Only the WAN will light back up. I have no connectivity to the router. I plug the laptop to the router directly and no LAN lights come on and can not see the router with arp -a.
View 6 Replies View RelatedCisco Routers :: How To Enable Telnet On RV180
Mar 9, 2013I'm trying to telnet into the my RV180 router. How do I go about it.
I created 3 VLANS
1 at 192.168.1.1
20 at 192.168.20.1
30 at 192.168.30.1
Here is the Multiple VLAN Subnet Table:
1 192.168.1.1 255.255.255.0DHCP ServerEnabled 10192.168.10.1255.255.255.0DHCP Server Enabled 20 192.168.20.1 255.255.255.0 DHCP ServerEnabled
I can ping the router at all 3 IP addresses.How do I enable the telnet service on the router?
Cisco Routers :: RV180 And IPSec VPN Client
May 22, 2012Does RV180 router support client VPN connections using regular Cisco VPN client? Datasheet says it works with Quick VPN client.
If regular non-Quick client is not supported, can both clients coexist (= be installed simultaneously) on the same PC?
Does Quick VPN client support split tunneling?
Cisco Routers :: Does The RV180 Series Support 6rd
May 10, 2012I'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.
View 1 Replies View RelatedCisco Routers :: RV180 Quick VPN To Connect
Aug 6, 2012I'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.
View 5 Replies View RelatedCisco Routers :: RV180 VPN Guide Required
Apr 3, 2013Is there a guide to setup a VPN connection using this router? I've follow the setup guide provided by cisco but I'm having issues. When attempting to connect using the quick vpn client, I get error messages.
View 1 Replies View RelatedCisco Routers :: RV180 IPSec Needs Polishing
Apr 26, 2013Any news on a new firmware for the RV180? I have the most recent version but it still has lots of bugs. IPSec needs polishing. In addition the Logging functions don't work well. I can't send to a syslog and when I try to email the logs I get a email saying there is no data even though several pages of enteries are visible in the web GUI. I've checked the profiles and they are correct. I even tried using just the 'default' profile but no luck.
View 2 Replies View RelatedCisco Routers :: SB RV180 VPN Users Not Showing Up?
May 15, 2013I have a Cisco Small Business RV180 and I have several VPN users configured. IPsec between my home router (also an RV180) and work router (router in question) is working fine, several PPTP users working fine and 1 QVPN user that works as well. I set up another qvpn user and it didn't work. I went back into the router to check and make sure I hadn't goofed something up and saw that I had 8 lines, 1 and 2 were the QVPN users and 6 other PPTP users, however, the "pages" footer (for lack of a better word) only displays 1 -5 of 5 instead of the 1-8 of 8 I would expect it to show.I dumped the cfg file and opened it up, all 8 user configurations show up. One was my user account which showed negative numbers for the logon time, something like -1day -hours -minutes -sec, so I thought that that might be locking up the router or something so I deleted my PPTP account but it didn't allow the new user access. I deleted all PPTP accounts and no luck there either.I'm running firmware 1.0.2.6.
View 4 Replies View RelatedCisco Routers :: RV180 Router Will Not Connect To ISP
May 16, 2012I am contemplating replacing my Juniper Netscreen 5GT with this new RV180.
serial number 161303LB
RVC180 V01
However, it will not connect to my ISP (DSLExtreme) using the same settings I have been using for multiple years. DSLExtreme is using AT&T DSLAMS, as you likely know, and I am unaware of anything unique about how they serve DHCP?
The Cisco wizard sits on the WAN configuration check forever, and never connects. I have rebooted it and allowed it to sit for fifteen minutes trying. I think that is enough.
The 5GT WAN interface is configured for "DCHP Client" and that is how the RV180 is configured.
It is a standard 6MB DSL line, I have tried both the existing cable, as well as the provided one to connect to the D-Link 2320B modem/bridge, which, as I indicated, syncs almost instantly with the Netscreen. No difference when the cables are swapped.