Cisco Routers :: RV180 / Setup Custom Service That Contains Both Multiple Disjoint Ports?
Jul 11, 2012
I have an rv180 and I'm trying to setup a custom service that contains both multiple disjoint ports (some UDP some TCP), as well as a TCP port range. This has lead me to a couple of questions.1) Is it even possible to have a single custom service with disjoint ports? Is it just going to be necessary to define multiple partial services for this?2) Is it possible to forward a range of ports? It's clear how to define a service with a port range, but the port forwarding table interface only allows me to select one LAN-side port for any service. Is there a secret notation that I need to do here that will just forward to the same LAN-side port as the WAN-side port---effectively one-to-one NAT forwarding, but just for the selected service?
View 8 Replies
ADVERTISEMENT
Feb 4, 2013
I have a Cisco RV180-K9-NA router. I would like to set up 2 separate VLAN assigned to different ports on the router. I will be using LAN port #1 to communicate with the router. The NIC connecting the PC to the router has multiple IP addresses assigned to it so that I can communicate with the separate VPNs (192.168.1.x for the router; 172.16.10.x for VLAN #1 on port 2; and 182.16.10.x for VLAN #2 on port 3). I also need to be able to have the router provide both IPv4 and IPv6 DHCP services for devices on each subnet.
View 3 Replies
View Related
Aug 6, 2012
Our firewall just died - it was a windows server 2003 rackmount running Microsoft ISA server. I'm shopping for a replacement, but would like to get an appliance rather than have to purchase a whole server, which just seems like overkill.
We had four network ports on the old box - one for internal, one for the cable modem, one for guest wifi, and one for the VPN (We have a dedicated Barracuda VPN appliance, so we won't be using the VPN functionality on whatever new router we purchase)
What we'd like to do is have a set of rules similar to what we had on the ISA server. We denied everything by default, and then for example: Allow outgoing HTTP, HTTPS, FTP access from guest wifi and internal network to the internetAllow access from the VPN subnet to certain ports on certain machines on the internal networkForward incoming access from the internet on port 443 to the VPN boxetc.
From reading the manual for the RV180, i could get a rough configuration going by putting internal, guest wifi and VPN on different VLANs, and disabling inter-VLAN routing for the guest wifi. However this doesn't get me the detailed control that I am used to - guest wifi and internal would be able to see the whole internet, and the vpn would be able to see anything on the internal network.
Does the RV180 can actually give you this level of control? What would be the most cost effective router from Cisco that could do this for me?
View 1 Replies
View Related
Jul 18, 2011
I've run a across a strange issue that I've not encountered before and after the things I've tried am beginning to think it's a limitation of the router itself. What I have are 3 Cisco 1941 routers that are all endpoints for a customer's MPLS network. STL is the headquarters and both remote offices have a link back this router. Each of the remote locations only have 1 serial interface. It is a flat network with few routes and a small shoretel voip system running across it. Each router is running C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M5, RELEASE SOFTWARE (fc2).
QoS is configured as follows on each router:
class-map match-any AutoQoS-VoIP-Remark
match ip dscp ef
match ip dscp cs3
match ip dscp af31
class-map match-any AutoQoS-VoIP-Control-UnTrust
match access-group name AutoQoS-VoIP-Control
class-map match-any AutoQoS-VoIP-RTP-UnTrust
[code]....
If I try to apply the policy map to serial0/0/0, I get the following error:
% policy map utoQos-Policy-Untrust not configured
I've tried to create a different policy map with the same settings and get the same error. We thought that when it was first set up, each interface belonged to the same network, so we separated things out (hence the .252 mask). I'm not sure what else to try and I'm hoping its something painfully simple that I'm missing.
View 2 Replies
View Related
Nov 10, 2012
I purchased the RV180 to replace a dead Linksys BEFVP41 to connect a home office to HQ. The Linksys was configured with three IPSEC tunnels to connect to three different subnets all through the main HQ gateway. Note that each tunnel is independent with its own pre-shared key. I can configure the same tunnels on the RV180, and each one works correctly, but I can only get one to run at a time. I have to disable the other two. Enabling a second tunnel results in the No phase2 handle found error. I could not use the Basic VPN setup as it complains that the remote endpoint is already in use. I had to use the Advanced VPN Setup to create the IKE and IPSEC policies. In a different discussion [URL]
View 3 Replies
View Related
Aug 2, 2012
I have a client that needs a VPN with multiple network address ranges on the far end of the IPSEC tunnel. Is this possible with this RV180 unit?
View 1 Replies
View Related
Mar 29, 2013
I want to setup a simple VPN to allow users to access the office via the iOS (iPad/iPhone) devices. I assume I do this through:
VPN>IPsec>Basic VPN Setup
BUT, what do I enter for the "Endpoint Information" and "Secure Connection Remote Accessibility"?
View 1 Replies
View Related
Aug 18, 2012
I bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
Seems the routing is not really working through the VPN Tunnel.
View 4 Replies
View Related
Sep 16, 2011
I am trying to set up a custom service on my netgear configuration page. I have a netgear router model# Wnr834m. every time i click the "add custom service" button the page redirects to "system authentication failed" and logs me out. What can i do to set up the new port?
View 1 Replies
View Related
Oct 24, 2011
I was wondering if I could setup my router CIsco RV120W to be able to connect to a VPN serice for my internet connection. Looking to give my small home netwok more sercurity. Is it possible with the Cisco firmware to be able to setup a connection to VPN serice. Do I have the compabilites with this router?
View 1 Replies
View Related
Sep 1, 2011
I am trying to set up my rv042 to use the ddns service. The rv042 is directly connected to the ISP provided modem on WAN port 1. The problem is that instead of seeing the internet IP the rv042 is using the ISP sub net assigned IP.
LAN IP : 192.168.1.1 WAN1 IP : 192.168.12.9 WAN2 IP : 0.0.0.0 Mode : Gateway DNS (WAN1) :DNS (WAN2) : 192.168.12.1 DDNS(WAN1 | WAN2) : Off | Off DMZ Host : Disabled
View 1 Replies
View Related
Oct 4, 2011
how can I block multiple ports on only 1 IP Address while not blocking those ports on other IP Addresses. I am using a Netgear WNR2000v1 which assigns the IP Addresses to each device.
View 1 Replies
View Related
Nov 27, 2011
is there a way to have multiple instances of user custom attributes and insert those as multiple instances of the A/V Pair in the authorisation profile in ACS 5.2/5.3 ?Background: We have to migrate a ACS 4.2 to 5.3. In ACS 4.2 our client used the multiline attribute
Number
#Name
#Description
#Type of Value
#Inbound/Outbound
[code]....
to specify multiple routes to various networks in the RADIUS reply spcific for every single PPP username of routers dialing in.Using the internal user database, extended by a string attribute and using that attribute as source of a dynamic value in the access-policy works basically. But as I have only ONE single line instance of the attribute for every user, I can only return ONE framed-route.We have lots of cases where multiple routes have to be assigned to one router.I 'd like to avoid defining a seperate access profile for every remote RAS router for external PPP Dial-In...[URL]
View 1 Replies
View Related
Dec 6, 2011
I have two cisco routers (Cisco 2911 and 871) that I'm trying to establish a L2L VPN with. Each have a VPN configured to our cooperate office that is up and working. I'm now trying to establish a site to site VPN from both remote offices. I have my crypto maps, NoNats, and interesting traffic set up however, I do not even see phase one come up.
I've attached each config. Most of my site to site experience is on PIX's and ASA so I'm curious if there is something else I need to do on my outside interface to allow multiple VPN's?
View 2 Replies
View Related
Apr 5, 2013
I was actually looking forward to setup multiple routers at our college(I know its quite late) where we have quite a good network of ethernet cables. Also, almost every cluster/lab has its own switch and we use static IPs with proxy to one network address(192.168.130.2). The user should be able to travel across multiple ROUTER/AP zones without changing connections.
all I got was I have to do something with MAC cloning and SSIDs.
View 6 Replies
View Related
Apr 7, 2011
At my company, we lease 3 static public IP addresses from 1 ISP. We want to have 3 separate networks that each use one of the IP addresses. Network 1 is the computer network, network 2 is the VOIP network, and network 3 is the security camera network. I am trying to determine the best way to do this. I have come up with 2 solutions in my head, but I'm not sure if they will work or not. I would like to get some input. Solution 1:Solution 1 looks something like this. Fiber box -> Router-> 3 switches. There would be one WAN input on the router, that would have a static route to 3 different LAN ports. For example, address 24.244.208.101 would be assigned to LAN port 1, 24.244.208.102 would be assigned to LAN port 2, and 24.244.208.103 would be assigned to LAN port 3 (by assigned, I mean have a static route to it). Is there some type of router that is capable of doing this? Solution 2:Solution 2 looks something like this. Fiber box -> Switch -> 3 Routers. The ethernet cable would run from the Fiber Box to a switch, and then 3 routers would be plugged into the switch. Each router would have the Static information configured in them. Would both of these methods work? If so, which would be the best way to go?
View 2 Replies
View Related
Apr 3, 2013
I have a Cisco RV016 router, with some ports configured in "Setup --> UPnP". Currently I have problems to configure new ports. I can create the service in "Service Management", but when I add this service to the list, I press "Save" and the router close the session. I need to re-login the router, and it don't save the changes.
However, if I add a service that was already exists before having this problems, the router save the changes (But the router close the session too).
The router has the last version of firmware since the first run.
View 4 Replies
View Related
Aug 30, 2012
I need to connect three sites. I also need to support some roving PCs connecting to the sites via VPN. With the RV180, can I support multiple ptp vpn connects between them, and at the same time, have the roving PCs connect to the RV180s.
View 0 Replies
View Related
Jul 6, 2011
how to setup and connect two RV082 routers together with a crossover cable between their WAN ports.This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 5 Replies
View Related
Dec 25, 2012
how to properly route multiple external IPs to internal ips assigned to several servers. Where I'm getting a bit lost is that I have two levels of routing - one from the outside into a comcast business class cable modem, which also creates its own internal network. Within that internal network, I have my RV180 router, which creates another separate internal network in which the servers live (don't want the servers to have access to other computers within the Comcast Modem's internal network). I want to map the external ips to servers within the RV180 second level network.
To diagram:
Comcast Cable Modem
/
RV180 Computer(s)
/
S1 S2
An internal IP is assigned to the RV180 router. Suppose it is 192.168.1.100.
The cable modem itself supports NAT as well. Do I use NAT twice (on both cable modem and RV180) to route the external IP to S1 and S2?
Or do I modify the routing table on the cable modem? Then use One to One NAT on the RV180 to map the external IPs directly to the internals?
View 2 Replies
View Related
Aug 9, 2012
I have some questions regarding the addition of custom services and their use in QoS for RV routers (I use the RV220W). Suppose I create a custom service as:
Name: My Service
Port: TCP 60000
1. Does this port number refer to the port number used by my LAN computer or the port number on the other side e.g. some computer on Internet I am using this service to connect to? Some services use the same port number on the side that initiates the service and the receiving end but there are services that use different ports for the initiating and receiving end. So, what is the meaning of the port number when creating a custom service?
LAN Computer : (port TCP 60000) <----> Internet computer : (some TCP port, not necessarily 60000) - or -
LAN Computer : (some TCP port, not necessarily 60000) <----> Internet computer : (TCP port 60000) ?
2. Suppose I create a QOS profile binding configuration with respect to this custom service for a specific IP address on my LAN. QOS is applied to the outgoing network traffic only. How is this profile going to work?
A. Applied to traffic originating from my LAN device with the specified IP address and port TCP 60000 - or -
B. Applied to traffic originating from my LAN device with the specified IP address to another computer's port TCP 60000 ?
View 9 Replies
View Related
Mar 25, 2013
I'm wondering if there is a possibility to get my homepage provider's custom dynamic DNS service working on my Cisco SRP541W Router as I'd not like to be forced to sign up for either DynDNS or TZO which are available through the web frontend.
View 1 Replies
View Related
May 14, 2013
How to create a mixed service ports on ASA 8.4(2)?I need to create a service group which has ICMP, TCP ports and also different UDP ports.Normally you would create different service group based on TCP/UDP/TCP-UDP/ICMP/Protocol and add then to new nested service group.But I want to create a new service group where you can define everything without the need to different service groups and nesting them into a new one.
View 1 Replies
View Related
Jan 29, 2011
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies
View Related
Mar 5, 2013
I use the Service port connected to the managementVLAN to manage the WLCs. When configuring HA with AP SSO, I lost HTTPS connectivity to the WLC, telnet still works fine.I researched the deployment guide and it states:
- When AP SSO is enabled, there is no SNMP/GUI access on the service port for both the WLCs in the HA setup.Why is remote access disabled using GUI when using HA, and how can I keep management of my WLC using HTTPS and an address in the ManagementVLAN.
View 10 Replies
View Related
Oct 29, 2011
I recently purchased an SG300-10 switch. Is it possible to change the TCP port numbers for the administrative services on this device? For example, if I wanted to change the web admin port from being availble on port 80 to port 8080, or move the SSH port from 22 to 2022, how would I do this?
I've looked over the web admin interface, and the Security > TCP/UDP services option looks like what I want, but I see no way to change a service's listening port. Is this possible?
View 3 Replies
View Related
Oct 28, 2012
can i set what websites I want to kid to have access to on a belkin N759 N+ router
View 2 Replies
View Related
Feb 26, 2013
I use ACS 5.3.0.40.8 with TACACS+ servicing Device AAA and RADIUS servicing the Cisco Wireless environment for AD user access. How can I implement 802.1x with the current RADIUS implementation with hindering current wireless users or am I hindered due to the EAP-GTC in use with PEAP via RADIUS?
View 3 Replies
View Related
Dec 23, 2012
Is there any way to manage the RV180 from the WAN side via https and/or ssh?Also, is ssh from LAN even available?
View 3 Replies
View Related
Oct 18, 2012
I have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.
View 6 Replies
View Related
Jun 17, 2012
I noticed if you add more than 10 access rules to the Access Rule table, you are unable to reorder past the first 10.Steps to reproduce:Create 11 rules of the same stream direction, outbound or inbound (...I found the bug with outbound, did not test inbound).try to reorder one of the first 10 rules to the end of the list, either by entering "11" manually, or by pressing the down arrow.System responds that "11" is an invalid number, or that the rule cannot be moved.This issue is not reported in the "Known Issues" section of the release notes for 1.0.1.9.
View 2 Replies
View Related
Mar 2, 2013
Which vpn client to use on os x ? (the one included in os x or another?) Which VPN configuration to use on RV180 ? and Which ports to open on RV180 Firewall ? (or any other parameters)
View 1 Replies
View Related
May 20, 2013
I had set up QOS for an IP Range and noticed the logs filling up with Warnings - hundreds within less than an hour.
I finally reset the router to factory and then step by step re-built my configuration - it was the QOS that started generating these warnings like:
Tue May 21 13:18:39 2013(GMT-0500) [rv180][Kernel][KERNEL] [87073.550000] IN=bdg1 OUT= DST MAC=d8:67:d9:c3:a0:2e SRC MAC=00:0e:58:58:57:7a PAYLOAD TYPE=08:00 SRC=192.168.1.193 DST=208.85.44.22 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=19313 DF PROTO=TCP SPT=1768 DPT=80 WINDOW=2534 RES=0x00 ACK URGP=0 MAR
[Code].....
In both cases above, after I started to suspect QOS, I entered a narrow IP range to test and then a MAC to test. Using a VLAN seems to work fine and generate no errors - even a VLAN for the same associated host(s).
I have a support case open about this - didn't get too far yet, but now with a better repro, maybe they will.
View 1 Replies
View Related
