I was actually looking forward to setup multiple routers at our college(I know its quite late) where we have quite a good network of ethernet cables. Also, almost every cluster/lab has its own switch and we use static IPs with proxy to one network address(192.168.130.2). The user should be able to travel across multiple ROUTER/AP zones without changing connections.
all I got was I have to do something with MAC cloning and SSIDs.
At my company, we lease 3 static public IP addresses from 1 ISP. We want to have 3 separate networks that each use one of the IP addresses. Network 1 is the computer network, network 2 is the VOIP network, and network 3 is the security camera network. I am trying to determine the best way to do this. I have come up with 2 solutions in my head, but I'm not sure if they will work or not. I would like to get some input. Solution 1:Solution 1 looks something like this. Fiber box -> Router-> 3 switches. There would be one WAN input on the router, that would have a static route to 3 different LAN ports. For example, address 24.244.208.101 would be assigned to LAN port 1, 24.244.208.102 would be assigned to LAN port 2, and 24.244.208.103 would be assigned to LAN port 3 (by assigned, I mean have a static route to it). Is there some type of router that is capable of doing this? Solution 2:Solution 2 looks something like this. Fiber box -> Switch -> 3 Routers. The ethernet cable would run from the Fiber Box to a switch, and then 3 routers would be plugged into the switch. Each router would have the Static information configured in them. Would both of these methods work? If so, which would be the best way to go?
View 2 Replies View RelatedI have two cisco routers (Cisco 2911 and 871) that I'm trying to establish a L2L VPN with. Each have a VPN configured to our cooperate office that is up and working. I'm now trying to establish a site to site VPN from both remote offices. I have my crypto maps, NoNats, and interesting traffic set up however, I do not even see phase one come up.
I've attached each config. Most of my site to site experience is on PIX's and ASA so I'm curious if there is something else I need to do on my outside interface to allow multiple VPN's?
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View RelatedI have an rv180 and I'm trying to setup a custom service that contains both multiple disjoint ports (some UDP some TCP), as well as a TCP port range. This has lead me to a couple of questions.1) Is it even possible to have a single custom service with disjoint ports? Is it just going to be necessary to define multiple partial services for this?2) Is it possible to forward a range of ports? It's clear how to define a service with a port range, but the port forwarding table interface only allows me to select one LAN-side port for any service. Is there a secret notation that I need to do here that will just forward to the same LAN-side port as the WAN-side port---effectively one-to-one NAT forwarding, but just for the selected service?
View 8 Replies View RelatedI need to setup my laptop for two different wireless configurations,at home i have a wireless network that work fine, however, at work i need to configure TCP/IPv4 by feeding in the required IP, Subnet Mask, Gateway etc. But i have to repeat this everyday in office and at home by removing and feeding in the parameters. Is there anyway that i can have both configurations and the system just automatically finds the right wireless network without changing the parameters. I am using windows 7.
View 4 Replies View RelatedI have one wireless router, 2 computers, 3 wifi laptops. so i want connect these all things in network.
View 1 Replies View Relatedsetup multiple wireless routers to one Internet connection. We have one cable modem (with built in wireless router) for Internet connection. Over a wide area (500 feet over two floors) I would like to connect to the Internet throughout this area wirelessly. The computers sharing the connection do not need to share with each other and do not need to see each other. Security is not a major factor. The building material is cinder brick walls (which weakens the wireless signal quickly).I have several older (2008 or 2009) wireless routers. I was thinking of putting these routers at various locations in the building with a wired connection back to the WAN modem. Each wireless router could the service a smaller area in the building.My plan is to turn off the DHCP on each wireless router. Do I need to run a wired cable (lan port to Lan port) back to the cable modem or can I use the wireless routers to connect to the wireless cable modem?
View 4 Replies View RelatedI manage the I.T. department for an ambulance service. We have 12 ambulances all equipped with Verizon 4G LTE Samsung hotspot cards. [code] There are laptops in each of the ambulances that connect to the wireless cards in the ambulance via DHCP. I get frequent problems when the vehicle get close to each other of them jumping from one card to another... which is not a huge problem, except when it happens the computer will have a "limited connectivity" to the internet. This sometimes will resolve after 3-5 minutes on its own, or if i disconnect from the wireless card and reconnect it will resolve, or sometimes by rebooting the wireless card it will resolve.We also need the ability to move the laptops from one ambulance to another as well so we need to have this flexibility.would I be better off establishing the same IP address to each of the wireless cards, still keeping different SSID's and different channel #'s and then hard code the IP address into the laptop instead of using DHCP to connect? My goal is to eliminate the limited connectivity issue.
View 3 Replies View RelatedWe have 36 cctv cameras slowing down our oracle network pc's all in same subnet. I want to remove the dvr's of cctv to a separate network to improve performance. How to accomplish that with a Rv042 linksys router? Or is there any other better way around. 5 Users access the cctv cameras all the time.
View 2 Replies View Relatedgetting a secondary isp as back-up and redundancy...and work arounds for ddos's....I just thought that i could use a switch/bridgeable router that can act as a switch... and run that off the first in line off the #1 isp router. Instead of connecting the second into the isp port, i should be able to put the #2 isp line into that. and put #1 ethercable into one of the outgoing ports from the second. And keep all the pc's on the #1 as is....But it should still use both providers simultaniously...right? I have 3 or more routers that can do this, and i have used them like this and shared several pc's internet's other then the primary ISP. But it was shared through the pc. and separate NICS or wifi AP's. I currently have one that will autosense a gig, and have bought another router that can operate at a gig that i plan to put into the #1 position as it's the fastest one. And will keep 1 gig without variability. and also give me wifi n 450-700. And they both support bridgeing,repeating and network balanceing /shareing. This should be possible and i won't have to spend $4,000 on a router with 2 ISP ports, and only uses it as fail-over....=c this should use both simulataniously and balance workloads between each.
View 2 Replies View RelatedHow do you setup multiple networks on one router? Is it as easy as changing subnets?
View 8 Replies View RelatedIs there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies View RelatedI have the following batch script which works except I cannot get the -W incrementing file flag to work. Everytime I run the script tcpdump will capture the traffic on my network but will overwrite the file each time. I just need it to write a new file with a sequence of file01, file02, file03?
@echo off
tcpdump -s 96 -c 50 -C 20 -W 50 -n -q -w tcpdumpbatchfile.dmp
exit
rem -s size
[code]....
I have the setup as following on my PC:
[code]...
I use the fibre internet for almost all internet activities since the speed is fast.However, when I do school's stuff, I need to VNC to my lab's server. Hence I need to connect to school internet point. External IP cannot directly connects to my school's server.Therefore, I would need to force Windows (or VNC) to use the connection of the Wireless Ethernet card when I VNC to my lab's server. But I want to use my fibre for all other internet activities.
I have to connect/switch to two different ips different gateways, can I possibly keep two set of ips always ready.
View 1 Replies View RelatedSo I'm building a house... in the living room there will be one server-like computer. This computer will also work with a NAS. So there will plenty of storage to place pictures and movies etc etc.Every room in the house will have a coax cable and CAT6. What I want is for fast file access to the server all computers in all rooms can use the CAT6 cable. That isn't the issue, because i will use network dives and mapping.e're planning on putting a TV in every room, so we want to perfect our media setup. But how can i make it, that the server will be able to stream different movies to different TV'S at the same time? The TV'S can get the video feed via coax? Or should I pull one more cable to all the rooms?So how can i have it that the media can be accessed at the same time? I can duplicate the monitors, but is it possible to have the server/computer play 2 or more different movies to different TV'S at once?
View 1 Replies View RelatedI remember the Virtual Server instead of Port Forwarding can be setup for multiple PCs to be Remote Desktop accessible from the Internet, but I forget how.
View 2 Replies View RelatedI'm trying to setup a VPN connection for the two PC's in the graphic below. I have the link between the two locations setup and secured, now I just working with the routing elements.what I need to add to the firewall config in order to get this to work? Here is what I have:
SITE A------access-list mpls_vpn_sitea extended permit ip host 172.168.199.1 host 172.168.199.2 access-list mpls_vpn_sitea extended permit ip TEST-LOCAL 255.255.255.0 TEST-REMOTE 255.255.255.0crypto map mpls_vpn 1 match address mpls_vpn_siteacrypto map mpls_vpn 1 set peer 172.168.199.2 crypto map mpls_vpn 1 set transform-set ESP-3DES-SHAcrypto map mpls_vpn interface MPLScrypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
SITE B------access-list mpls_vpn_siteb extended permit ip host 172.168.199.2 host 172.168.199.1 access-list mpls_vpn_siteb extended permit ip TEST-LOCAL 255.255.255.0 TEST-REMOTE 255.255.255.0crypto map mpls_vpn 1 match address mpls_vpn_sitebcrypto map mpls_vpn 1 set peer 172.168.199.1 crypto map mpls_vpn 1 set transform-set ESP-3DES-SHAcrypto map mpls_vpn interface MPLScrypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
do I need to specify a route between the two networks? What do I need to have for NAT statements?
I've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
View 5 Replies View RelatedI have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies View RelatedI have set up a filezilla server, and connected to it, and was able to access my files in the main drive (C:/), but at this point the unsolvable problem for me has to do with being able to access multiple drives wirelessly.Filezilla's FAQ says it has to do with aliases, etc, but when I tried this, my main drive dissappeared and I was only able to access the alias drive.All I wanted to do was back my Android's content up to my computer. From what I understand, FTP is a good way to do this. Let me ask you something....is it possible to upload stuff to my computer's ftp server even without being connected to the same wifi network?
View 3 Replies View RelatedI have a Netgear ProSafe VPN Firewall FVX538. But I also have 10 Public IP Addresses that I will like to setup for three web services. So how do I set this up. With multiple routers. Or can my Netgear FVX538 take multiple Public IP Addresses to the same ports. If not how can setup multiple routers. one being the main one.
View 1 Replies View RelatedWe have a Cisco 887 router and a Cisco SG-200 switch.We'd like to setup trunking between these 2 devices for multiple VLANs on the switch to be made available on the router.
With previous routers, you could set the router up in the configuration 'router-on-a-stick' and VLANs worked like a charm but the 887 no longer support sub-interfaces.So how can you get trunking working between the 2 devices?
Is there a VTP configuration menu for the SG-200 which we can setup in order for it to talk 'VTP' with the 887 router??
I would like to setup multiple DMZs for our hosting servers. Currently there is a single DMZ in which our reverse proxy servers are connected using a public IP address. The idea is to have the reverse proxy forward the request from the Internet to the hosting servers in another DMZ. The purpose of the hosting DMZ is to protect it from the outside as well as from the inside. There will also be a development DMZ where we can test content prior to going live with the website.
Network: We currently have two Cisco 6509's (Core) with a FWSM in each running active/stanby configuration. There is a 10Gb Fiber connection between each Cisco switch to two Cisco 4948s (Top of Rack Switches). I can either setup OSPF or Trunking between the core and top of rack switches. The Cisco 4948s will support VLAN 7 (hosting DMZ 10.0.7.0/24) and VLAN 8 (development DMZ 10.0.8.0/24). Each webserver is connected to both Cisco 4948 for redundancy.
Question: If I have a single interface connecting both VLANs 7 and 8, either through Layer 2 or 3, then how can pass both DMZ traffic to the appropriate servers? The reason why the servers are in the same rack connected to the same two switches is that we are using Blade Servers and VMWare.
In my office we have concrete walls and very limited wiring. The way it is set up is we have a Verizon DSL Modem that comes in then I have a router with it that splits the signal to 4 other routers that each split the signal 2 to 3 more times. I have to use routers so that it assigns IP addresses.I bought a new D-Line N300 Wireless router with USB imput. I want to attach my Home Media Network Hard Drive Cloud edition to the 1st router (attached to the modem) and then share the data off that hard drive with everyone connected to the sub routers.
View 4 Replies View RelatedMy current setup is a wired connection from modem in office to Linksys WRT54G2v1 in livingroom and from it I have wired connections to Mac & Laptop back into office, Apple TV and another Linksys WRT160Nv3 located in far bedroom.The reason for this setup is that my home has been a vortex of death for wireless and cell receptionI have a guest house on same side of house as far bedroom and in order to get single to the person living there, I put in the WRT160N in the bedroom. This setup works but lately the 54G causing the wired connections to loose internet connectivity.This seems to happen to me every 2 years with Linksys and I end up buying newI purchased a D-Link EBR-2310 v2.01 non wireless router to put in and take all the wired connections off the 54G. But I fear I'll break everything when I try this. How best to treat the Linksys routers if I have the D-Link as the primary router
View 4 Replies View RelatedI just received a new Cisco SG300-10 and am configuring it in Layer 3 mode. I am trying to setup multiple routed VLANs going back to a FiOS Actiontec router. My configuration is as follows.
Fios Router: 192.168.1.1
Assigning DHCP 192.168.1.2 through 100.
SG300-10 has VLan 1 ip 192.168.1.5 used for Mgmt.
VLAN2 is 10.0.2.1
VLAN3 is 10.0.3.1.
I have a static route set on the fios router for both subnets setup as follows.
Destination 10.0.3.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
Destination 10.0.2.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
I have a laptop connected to Gi8 on the Cisco (Vlan 3) and statically assigned 10.0.3.3, with a gateway of 10.0.3.1. DNS set to the fios router (192.168.1.1).
Everything pretty much works EXCEPT, I cannot get out to the internet from either vlan. Traffic routes between vlans/and the default subnet on the fios without issue.
When I ping out, DNS resolves, but will not go past the fios router. Am I missing a setting somewhere?
My adolescent son wants to create a server to host video games. We, the parents, want to separate our computers and files from all the crazy security risks my son and his friends take, while allowing them to learn by their mistakes.I want 2 separate networks, or does this make sense? Would love to have our computers (assorted PC's, Macs, both laptops and desktops, running Vista Ultimate, Windows 7, OSX 10.5 and up), ipods, TV's, Blu-rays, wireless printers, etc. isolated from our son's computers, ipods, TV's, XBox, Blurays, wireless printers, (as well as the digital stuff his friends bring over).Since security is the reason for this, would love any tips over and above Brian Posey's article on Tech Republic (5 common security mistakes people make on setting up wireless networks, or something like that)We have Optimum high speed (testing up to 65 mps) internet service and 5 static IP addresses to work with.
View 4 Replies View Relatedhow i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View RelatedI have recently moved into a new flat and with my wireless router in my livingroom I am unable to get good signal in either of the bedrooms? Its a more or less open plan flat so unless I have lead in the walls or something silly like that stopping the signal.What I am trying to do is have a wireless router in the livingroom and then one in the hall way so if I have a laptop in either the livingroom or bedrooms I will still pick up signal from the closest router!I currently have a brand new Netgear DGND3300v2, Netgear DG834PN, Sagem F@ST2504 and a BT Home Hub 2.I have read about having routers act as access points and the like but I am not great with networking to be honest. I have good computer skills so if it is explained to me I can pick it up rather well.I would like the wireless router in the hall way to pick up the internet from the wireless router in the livingroom... wirelessly!
View 1 Replies View RelatedI am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?