I'm wondering if there is a possibility to get my homepage provider's custom dynamic DNS service working on my Cisco SRP541W Router as I'd not like to be forced to sign up for either DynDNS or TZO which are available through the web frontend.
View 1 Repliesi have gotten a question from a partner in regards to the throughput on both LAN and WAN on the SRP541W. I can't really find that on the datasheet.
View 4 Replies View RelatedI just bought the SRP541, and it has the old firmware. I downloaded the new firmware, yet I cannot figure out how to install it.
View 3 Replies View RelatedRecently we have purchased a few SRP541W for our small branch office VPN sites. While working with the config I have discoved that when trying to create a IPSec VPN policy, I am limited to only one "remote network" entry. This is typically not how VPN tunnels are bulit. We generally put the following remote networks in the tunnel. How do I open a BUG ticket with Cisco and ask that they change the code?
View 3 Replies View RelatedI am curious of the max supported SIP sessionf of the SRP500 series.
View 1 Replies View RelatedI'm running FW 1.02.01 (23) and I'm having problems with the DNS proxy. I have DNS Proxy enabled for my DHCP server on the router and I have my dns server programmed into the global dns location. I cannot ping any DNS names for my IPSEC VPN tunnel.
View 2 Replies View RelatedI have an SRP541W with two ADSL modems attached to it. Both are running bridged mode with PPPoE connections to two different ISPs, (TPG and Telstra Business Direct). The TPG connection is far cheaper, and has a much higher download limit. Sadly, if I leave the router in "load Balance" mode for the WAN, it "prefers" the Tesltra connection because it's faster. I want downloads for movies/music, Youtube, Internet Radio, etc, to go through the TPG connection. Is it possible to do this in the router, or would I need to set up a proxy server, (or some other external device/application)?
View 5 Replies View RelatedWe purchased a Cisco 541w router for one of our customers.
The main reason was to provide them with 3g backup solution for their business.
In order for the router to recognise the 3G router the firmware was upgraded SRP540_1.02.01_023_081211_1136.
We arrived on site last night to do the install but couldn't make any changes to the already configured router. Every time we attempted add a vlan or adjust the dhcp scope the router would return "The values are invalid".
Worked at this for over 1 hour and then decided to factory reset the router to see if that would revert the router to use the original firmware.
This didn't revert to the previous firmware but we magically could now make network changes without problem.
So everything was good, we reconfigured the router, tested 3G and failed the wan1 interface back and forth and the customer was very happy.
Customer arrived onsite this morning and the router was running on 3G. Every 8 - 10 minutes it was attempting a failover between connections.
I decided to turn off the failover for the time being and investigate further but yet again i was back to "the values are invalid"
We've had to pull the router as the customer is about 2hours away and revert back to their BT router.
Found this document for another SRP model - A warning message may appear in the Basic Wireless Settings screen with the text “The values are invalid” when modifying the wireless profile. Set the SRP 521W to its default setting (CSCtd49614).
[URL]
Will firmware SRP540_1.2.4_003_011112_1847 released only 2 days ago cure the problem?
the small fan of a SRP541w seems to have 'melted' it's way out of it's casing. How to know part number for a replacement fan for this router?
View 3 Replies View RelatedI'm running FW 1.2.4 and how to setup Remote Web Access over my IPSEC vpn tunnel. I would like to be able to remotely access these routers and make configuration changes from my main office but I cannot seem to figure out how to get it to work. If I try to access the internal router IP from across the VPN, I cannot. My VPN tunnel is up and operational and I can ping various devices across the tunnel but I cannot access the web management of the router.
View 4 Replies View RelatedI've configured an srp541w router for a customer and successfully configured an IPSEC VPN connection with a Netopia router at a satellite office for the customer.
I cannot seem to find a way to configure either a PPTP VPN connection or QuickVPN connection for remote users. I did read something that stated that the router will only support either a site-to-site VPN or a QuickVPN connection, but not both at the same time.
I am using an SRP541W router and i am trying to configure 2 vlans, each one to use its own Wan:Here are the dhcprules and vlans:As can be seen, each one has its own wan interface.
Vlans:As can be seen, each vlan is using its own ports and dhcp rule, so, now they should be separate.
Both Wans are connected: So now (at least as i see things) the two vlans are separate and using different Wan. But the reality is different, everything is going out using Wan1.Also in the Interface Info you can see that the 2 vlans are listed under the Wan1.
The rest of router setting are default.
We have an SRP541W on which I thought I had disabled DHCP, its turns out that in fact I haven't. After seaching again for the DHCP on/off funtion I found it under the Vlan settings (Wierd place to put it I thought).
The Router has a static ip address on the LAN side of 192.168.1.254 and is connected to a Cisco 2700 series on the WAN side. Our network DHCP is served by an SBS 2011 server hence my reason to switch off DHCP on the router. However when I select Static IP address from the Address Type in the VLAN settings and try and save the changes I get an error that is IP Address / Subnet Mask value is illegal. Great but why when the router has and IP address assigned and the subnet mask is set do I get this error. On the VLAN settings page there is no option to set an IP Address
Is there any way to setup an IPSEC tunnel to be able to go from my subnet, 192.168.75.x and be able to reach anything on the other side of the tunnel, 192.168.X.X?
View 5 Replies View RelatedUnfortunately, it does not appear as if the SRP500 series will allow you to create an ipsec policy where the local or remote traffic selection is 0.0.0.0/0.0.0.0. It wants a specific network. I have a scenario where I want to send all traffic over the vpn tunnel.
Is there a workaround to this or a special way to input "ANY" as the remote network?
I have a problem connecting SRP541W to my ISP (L2TP). Connection is established, but default routing table is wrong: instead of gateway I see Server IP: [code]
In similar situations other users of my ISP with Cisco routers (IOS) solved this problem by adding command no peer neighbor-route but i can't do it through the WEBgui...
I have some questions regarding the addition of custom services and their use in QoS for RV routers (I use the RV220W). Suppose I create a custom service as:
Name: My Service
Port: TCP 60000
1. Does this port number refer to the port number used by my LAN computer or the port number on the other side e.g. some computer on Internet I am using this service to connect to? Some services use the same port number on the side that initiates the service and the receiving end but there are services that use different ports for the initiating and receiving end. So, what is the meaning of the port number when creating a custom service?
LAN Computer : (port TCP 60000) <----> Internet computer : (some TCP port, not necessarily 60000) - or -
LAN Computer : (some TCP port, not necessarily 60000) <----> Internet computer : (TCP port 60000) ?
2. Suppose I create a QOS profile binding configuration with respect to this custom service for a specific IP address on my LAN. QOS is applied to the outgoing network traffic only. How is this profile going to work?
A. Applied to traffic originating from my LAN device with the specified IP address and port TCP 60000 - or -
B. Applied to traffic originating from my LAN device with the specified IP address to another computer's port TCP 60000 ?
Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies View RelatedOur firewall just died - it was a windows server 2003 rackmount running Microsoft ISA server. I'm shopping for a replacement, but would like to get an appliance rather than have to purchase a whole server, which just seems like overkill.
We had four network ports on the old box - one for internal, one for the cable modem, one for guest wifi, and one for the VPN (We have a dedicated Barracuda VPN appliance, so we won't be using the VPN functionality on whatever new router we purchase)
What we'd like to do is have a set of rules similar to what we had on the ISA server. We denied everything by default, and then for example: Allow outgoing HTTP, HTTPS, FTP access from guest wifi and internal network to the internetAllow access from the VPN subnet to certain ports on certain machines on the internal networkForward incoming access from the internet on port 443 to the VPN boxetc.
From reading the manual for the RV180, i could get a rough configuration going by putting internal, guest wifi and VPN on different VLANs, and disabling inter-VLAN routing for the guest wifi. However this doesn't get me the detailed control that I am used to - guest wifi and internal would be able to see the whole internet, and the vpn would be able to see anything on the internal network.
Does the RV180 can actually give you this level of control? What would be the most cost effective router from Cisco that could do this for me?
I have an rv180 and I'm trying to setup a custom service that contains both multiple disjoint ports (some UDP some TCP), as well as a TCP port range. This has lead me to a couple of questions.1) Is it even possible to have a single custom service with disjoint ports? Is it just going to be necessary to define multiple partial services for this?2) Is it possible to forward a range of ports? It's clear how to define a service with a port range, but the port forwarding table interface only allows me to select one LAN-side port for any service. Is there a secret notation that I need to do here that will just forward to the same LAN-side port as the WAN-side port---effectively one-to-one NAT forwarding, but just for the selected service?
View 8 Replies View Relatedcan i set what websites I want to kid to have access to on a belkin N759 N+ router
View 2 Replies View RelatedI've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies View RelatedI used to have a DLINK router which covered my whole house with its Wifi signal. After upgrading to the SRP541W router, only the very close vicinity of the router has any acceptable level of signal to use devices. I seriously need to improve WIFI range to accomodate my small business. I asked the Live chat technician and the answer was "This device does not support external antennae" and then silence. Okay it is not supported but what I am looking for is a solution, not a dead end.
For example, is there a cisco repeater/extender that I could deploy that works with the SRP541W router? Any experience adding one long cable and putting one antenna at a different location of the house?
I am new to VLANs although I generally understand the concept. I have a small office with 25 desktop/laptops and 15 VoIP phones connected with a SG200-50 switch and on Port 1 I have the Cisco SRP541W router for DHCP and Internet access. My goal is simple: 1) Segregate the VoIP phones (voice) from the computers (data) and 2) Prioritize the VoIP phones traffic.
I believe this can be accomplished by setting up a second VLAN and maybe a third (if the default should not be used) and then identifying those ports as Voice VLAN ports. I guess I just need to know how to flag each interface and each port so that they all can talk to the router on Port 1 yet the voice and data will be in different broadcast domains. Also, do I need a management VLAN??
Is this setup correct? VLAN 1 - default (data) Port 1 (Trunk) (Tagged)Port 2 - 30 (Access) (Untagged)VLAN 2 - voice Port 1 (Trunk) (Tagged)Port 31 - 48 (Access) (Untagged) What should the interface settings be on each port (General, Access or Trunk)? What should the port VLAN membership be on each port (Tagged or Untagged)??
Using a command prompt, how do I discover the internal IP of an unused router, which I set to a custom value and forgot? The router is not currently in use for internet access. I would like to access the control panel of the router without resetting it.I attached my netbook to the router with an RJ45 cable and disabled the netbook's wireless adapter to avoid conflicts with my current network. Using an elevated command prompt, I did an "ipconfig /release", rebooted and ran "ipconfig /all", but the gateway entry is blank. An "arp -a" returns 169.254.190.120 as the only interface. A "netstat -a" returns 169.254.190.120:xx...'s, 127.0.0.1:xx...'s, and 0.0.0.0:xx...'s, but no router internal IP address.Is there a way discover the attached device without resetting?
View 1 Replies View RelatedI'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
I have a Netgear WNDR3400 router and I would like to just dabble with it and see if I can't get any more performance out of it. I checked dd-wrt already and it isn't supported yet. Any other place to get custom firmware for my router type?
View 3 Replies View RelatedI just switched from a Linksys Router to the RV215W, I was able to put custom dns servers for my wan, ie. opendns, but now in cisco, I'm missing this feature.
Does any one know how to set-up a workarround with DHCP from my ISP and access custum dns servers..
When are we gonna have this feature implemented in the WAN secction.
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.8 Build 110418 Rel.43954n
ISP : SBB - Serbia Broadband[/COLOR]
I have been usung TP link for years, and now I want to use the 3G modem option the 3420 offers. But in the list of countries I can't find Serbia, and I can't find the ZTE MF 195. I found that on the TP Links site list of compatible modems there is Other countries, but in the modem list there isn't such an option, and since there is also no ZTE MF 195, and there isn't a "Telenor" entry for the service provider.I tried telling the router that I'm from another country, and setting up some of the parameters manually, but "surprisingly" it didn't work. Is there or could someone make a program which makes BIN files specific to the modem that isn't on the list, or is there a place where the BIN files grow?
I'm setting up a site-to-site VPN with an RV082 ( and an RV042). The RV042 is behind an Actiontec modem/router that has the local public IP address. So, this address is registered with dyndns so we can find it with a name.
The name is entered into the RV082 VPN Remote Group Setup as: Dynamic IP + Domain Name (FQDN) Authentication The given name for the dynamic IP is entered into Domain Name: But, in the summary, the entry for the Remote Gateway shows only the name and 0.0.0.0 for the IP address.
This same RV082 can get the same IP address from a ping of the name just fine.
We just purchased the WRVS4400N router with high hopes. For some reason, our ISP provides a connection through L2TP Dynamic for a static IP. I repeat, L2TP Dynamic. Is there anyway to properly configure the router to use such a connection method. I only see L2TP Static, which seems to be the standard method for many routers.
View 1 Replies View RelatedI'm trying to combine dynamic and static NAT on a SR520. My dynamic NAT is specified with:ip nat inside source list 1 interface Dialer0 overload access-list 1 permit 192.168.0.0 0.0.7.255 In addition to this I want to perform static NAT for a couple of selected internal hosts. I can do this:ip nat inside source static 192.168.1.5 10.85.10.2 which works fine but means that the source address 192.168.1.5 is translated to 10.85.10.2 for all destination IPs. What I want is for the above static translation only to occur for a particular destination subnet.To accomplish this I have tried:
ip nat inside source static 192.168.1.5 10.85.10.2 route-map toOtherSite
route-map toOtherSite permit 10
match ip address 150
access-list 150 permit ip 192.168.1.0 0.0.0.255 192.168.10.0 0.0.0.255
But this does not appear to work. Instead it seems to render the host 192.168.1.5 unable to progress through the NAT, whether the destination subnet is 192.168.10.0/24 or not, and I can't work out what I'm doing wrong.
I purchased 2 RV042's (h/w version 3) less than two months ago. I updated them to the latest firmware (v4.0.4.02-tm (Jul 4 2011 13:30:56)), did a factory reset to make sure I was working with a clean slate, set up DDNS through DynDNS and a site to site VPN between the two. Everything was working great for a month, then the DynDNS accounts expired because they weren't being updated. I reactivated the names on the DynDNS site, and started to monitor the "last updated" date and time. After 24 hours there were no updates according to the DynDNS site. I logged into one of the RV042's, and it said "Dyndns Enabled : Dynamic DNS is updated successfully." This is a stale message from 24 hours ago when I hit save. So I went into Setup | Dynamic DNS | Edit Config and there it also says "Dynamic DNS is updated successfully." I clicked "Save", status changed to " Dyndns Enabled : Updating..." for a few seconds, and then back to "Dyndns Enabled : Dynamic DNS is updated successfully". I refreshed the DynDNS website and it shows the current time (in eastern time, i'm pacfic) as the last time it was updated. So it works when I manually hit the "Save" button. Not making any changed, just hitting "Save". I've let the other RV042 go over 48 hours and it still hasn't updated. So it apears for the time being, I'll have to remember to push the "Save" button once a week to prevent my DynDNS accout from expiring. Does DDNS working in the lastest firmware and h/w version 3? If so, what is the update frequency?
View 6 Replies View Related