Cisco WAN :: Does 887VGW-GNA-K9 Support ADSL?
Mar 22, 2012My customer need 3G+WiFi+ADSL, Does CISCO887VGW-GNA-K9 will support ADSL or not
View 3 Replies
ADVERTISEMENT
Cisco WAN :: 1760 Support For AT&T's ADSL?
May 5, 2013Need config for a 1760 to support AT&T's ADSL 6meg, I would like to compare it to what I have.
View 2 Replies View RelatedCisco WAN :: Does 877 Router Support DSL (not ADSL)
Mar 24, 2013does Cisco 877 router support DSL (not ADSL?). i have tried connecting a dsl line and cant get ATM interface to come up - username and password are correct.alternative option: Can i get cisco 877 to form a ipsec tunnel using LAN port (not dialer interface) ? basically i want this 877 to act like asa 5505 where i can connect a LAN cable coming out from DSL router?
View 3 Replies View RelatedCisco Infrastructure :: Will WIC SHDSL-V3 Able To Support ADSL Line
Apr 10, 2013I do have a question, is WIC-1SHDSL-V3 able to support ADSL line?
We have WIC-1SHDSL-V3 module used for SDSL line, due to few site need to bring up with ADSL line with 1841 model, but HWIC-1ADSL module already EOS. The replacement model EHWIC-VA-DSL-A is not compatible to 1841. My architect suggest Symmetric Module like WIC-1SHDSL-V3 could be able to tweak the config to support Asymmetric purpose. I did google but do not found such related topic. Can any expert on this area to advice me?
Cisco WAN :: 2911 - Support Interface ADSL Module Like Backup Link?
Apr 27, 2011i will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.
View 1 Replies View RelatedCisco WAN :: Connecting ADSL Line On HWIC-ADSL On Router 2901?
Aug 24, 2012i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedWireless :: Can Wireless Router Support Up To 100 User Including Support Network Printer
Feb 16, 2011can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedCisco WAN :: 837 - Simple ADSL Configuration
Feb 11, 2011I need to configure ADSL on my 837 Router with simple configuration. The WAN IP address is dynamic from my ISP. I checked many websites and found different configurations everywhere. I don't know which is best suited for me. I used SDM and configured ADSL. When i checked the configuration from console i found that there is atm0.2 and dialer 2 configured with my settings. I cannot understand what is the purpose of atm0.2 and dialer 2 when atm0 and dialer0 are there. Is there a doc on ADSL config on 837?
interface Ethernet0 ip tcp adjust-mss 1412 exitinterface ATM0.2 point-to-point no shutdown pvc 0/35 pppoe-client dial-pool-number 1 exit exitinterface Dialer2 exitdefault interface Dialer2interface Dialer2 ip mtu 1452 no shutdown ip address negotiated dialer pool 1 dialer-group 1 encapsulation ppp dialer idle-timeout 120 dialer fast-idle 20 ppp authentication chap pap callin ppp pap sent-username username ppp chap password 0 password exitdialer-list 1 protocol ip permit
Cisco WAN :: 2911 / Configure BGP Over The ADSL?
May 19, 2011I've got a 2911 with a primary ethernet link to the ISP, with BGP running over it. There's also an ADSL module in it, which will connect into the same ISP AS. how do i configure BGP over the ADSL so that it sits there doing nothing until the primary link fails? Do i need to setup a new instance of BGP with a different AS on the router or can it sit in the same AS as the primary link?
View 1 Replies View RelatedCisco WAN :: ADSL Configuration On 887 Router?
Aug 1, 2011I am installing a Cisco 887 to a ADSL2 Circuit and I cannot connect to the ADSL eventhough the show interface shows that both the ATM0.1 and Dialler 0 is up.
The configuration of the router is below.
Building configuration...
Current configuration : 5980 bytes
!
! Last configuration change at 11:12:58 PCTime Wed Aug 3 2011 by cisco
[Code].....
Cisco WAN :: 2600 - How To Use DMZ Like ADsl Modem
Mar 14, 2013I am new using cisco router 2600, i want to use dmz like adsl modem to direct ip public to ip lan like 180.15.22.x.x to ip lan 192.168.1.2 ( lrouter mikrotik ) outside to inside so when i call ip public then forrward to mikrotik
View 2 Replies View RelatedCisco WAN :: 877 ADSL Firmware Change Log
Feb 1, 2011Where I can find the change logs for the ADSL Firmware's.I realize each firmware comes with its individual bug fixes, however there is usually a significant difference between the shipped firmware and latest firmware available.i.e. the 877m is shipped with 3.0.14 and the latest is 3.0.33. We have a handfull of miscellaneous issues, across a variety of hardware and customers, and would like to scan through the change logs to see if any of these issues were addressed by a previous bug fix.
View 2 Replies View RelatedCisco WAN :: 1841 WIC 1 ADSL Configuration
Dec 12, 2011I am configuring a 1841 router for use in small out office. I will use the s0/0/0 for main WAN T1 connection. I then wanted to use the ATM0/1/0 WIC-1-ADSL card as a failover. I am using weighted static routes for failover. Fe0/0 is LAN interface. When I go into SDM and look at the ATM interface it says this configuration is unsupported?
1. Can't I just get a DSL modem and connect it to fe0/1 and not use ATM WIC and use below for failover?
2. If I have to use ATM WIC what needs to be configured for it to work with Att aDSL?
Cisco WAN :: 857 ADSL - How To Migrate To FTTC
Mar 26, 2011convert a few connections from ADSL to FTTC but would like not to have to replace the Cisco 857 router already installed.To achieve this I would need to allocate one of the Ethernet ports as the WAN interface and configure PPPOE for authentication.
View 1 Replies View RelatedCisco WAN :: 827 ADSL Router IOS Upgrade?
May 5, 2013My professor have asked us to do an IOS upgrade for a Cisco 827 ADSL Router. But I´am having problems to find the appropiate IOS image. The router original IOS is c827-y6-mz.121-1.XB and it supports routing protocols like rip bgp eigrp ospf is-is, etc.
Now, we have to find a newer IOS release that supports the same amount of routing protocols. This Router has only 24 MB DRAM and 8 MB Flash. We have tried with a IP PLUS/FW/IPSEC release 12.3(26) but when I write : route ? it only shows eigrp, odr and rip.
I am searching for a newer release that fits in those 24 MB and which has the other need routing protocols like ospf,bgp, etc.
an IOS image that meets what I am searching for?
Cisco WAN :: 886VAW Not Syncing At ADSL?
Aug 30, 2012y newly purchased 886VAW won't sync. The link ( ISDN ) I'm running it off from runs nicely on my crusty-trusty 803. I linked the box with the cables supplied against the splitter as usual but can't seem to get a stable CD light ( constantly flashing ). The box is intended to run against ADSL (with VDSL to come in a few days ).
Controller VDSL 0 is DOWN
Daemon Status: Establishing Link
XTU-R (DS) XTU-C (US)
[Code].....
Cisco WAN :: WRVS4400n / Routing VPN Over ADSL?
Jan 14, 2011I have this sytuaction.
LAN_A-->WRVS4400n-->WAG160N--->INTERNET<---WAG54GS<--WRVS4400n<--LAN_B
I want make VPN between WRVS4400n.
LAN_ALAN_BWRVS4400n: Lan 192.168.10.11 WAN 192.168.9.11
WAG160N: Lan 192.168.9.10 WAN static IP xx.xx.xx.81
WRVS4400n: Lan 192.168.2.11 WAN 192.168.1.11
WAG54GS: 192.168.1.10 WAN static IP xx.xx.xx.95
On the tests in WAG-s all ports are forwarding on WRVS and I open 8080 for Remote Management in WRVS. I can get acces to bouth WRVS by Remote Management from outside networks. I make in bouth WRVS client vpn, but when I want connet by OpenVPN Cilent, I have access for few seccend and I get notificatin that the network not respond. Some time i get connection for long time.
Tunels configuration
NET ANET BTunel name: NET_A
Local Group Setup
Local Security Gateway Type: IP only
Local IP: 192.168.9.11
Local Security Group Type: subnet
IP. 192.168.10.0
[code]....
When I change ADSL to bridge mode the VPN tunels are working and OpenVPN Cilent connect normaly. But I thing that the solution with adsl mode bridge isn't safely like forwarding ports and routing.
Cisco WAN :: 891 - Configuration Behind ADSL Router
Jan 28, 2012I would like to configure cisco 891 behind an ADSL Router(ISP one).The Details are:
ADSL Router:
- DSL Connection: dynamic IP
- LAN: 10.153.66.1/255.255.255.128
CISCO 891
- WAN: 10.153.66.5/255.255.255.128
- LAN: 10.153.64.1/255.255.255.128
- Configuration:
WAN
interface FastEthernet8
description Singtel Line$ETH-WAN$$FW_OUTSIDE$
ip address 10.153.66.5 255.255.255.128
[code]....
I could ping to 10.153.66.1(ADSL Router), but I cannot connect to the internet.
Cisco WAN :: 877 - ADSL Line Drops
Nov 8, 2010We have a fairly major problem with some of our Cisco 877 units (5 in all). All are running 15.2(2)T2 in order to make use of zone-based firewalls and virtual reassembly, and all are exhibiting the same problem. When our ADSL line drops this si shown in syslog
2010-11-09 01:03:06 Local7.Info 192.168.7.1 4733: Nov 9 01:03:05.707: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41799 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident 02010-11-09 01:04:06 Local7.Info 192.168.7.1 4734: Nov 9 01:04:05.946: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41809 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident
[code]...
The "no retrain. sleep 20 seconds" messages continue forever more until somebody power-cycles the router - which is a bit inconvenient as two are 300 miles away. Surprisingly, our event manager applet isn't triggering the reload either, which defeats the object.
Cisco WAN :: 837 ADSL Router Setup
May 16, 2013I have a bit of an issue setting up an Cisco 837/SOHO ADSL Router.
Basically what it is is that my Broadband router isnt doing its job very well, and the last piece of the puzzle in the server area is to upgrade the router, and I have with this. Now. I hve followed the setups as per cisco's guidlines very well and doen alot of research on the CLI commands, I have access to the router and have setup the system.
My broadband in the office is Orange/EE and its PPPoA. I hvae all the settings, and such and have followed a set of commands that apply to BT broadband but, It simply hasnt worked in my case. Any CLI commands to setup this router so i'll replace my business livebox.
Cisco :: ADSL Comes Under Circuit Or Packet Switching?
Dec 3, 2011I found that ADSL is packet switching type of communictaion. Definition for circuit switching is "A type of communications in which a dedicated channel (or circuit) is established for the duration of a transmission."In practical, telco line connects to the ADSL modem/router through which we are communicating to internet.In this context I have some doubt.The telco line which is connected to our ADSL modem is not shared with any other device ,connects only to the CO of the telco where we get the internet connection.That means the line which connects to the modem is dedicated upto CO.then it becomes circuit switching or not upto the CO.
View 5 Replies View RelatedCisco Router 877W ADSL Configuration?
Nov 18, 2012While i was looking around in my stuff in the office i have found a Cisco 877W ADSL router .. so i have decided to use it instead of the one i am using now which is provided by the ISP that's made by Huawei.Anyway i have a good knowledge about basic cisco router configuration but i had never configured ADSL Cisco router, so i looked around on Cisco website, and i was lucky to get this two linksCisco DSL Router Configuration and Troubleshooting Guide - Step-by-Step Configuration of PPPoA with a Dynamic IP Address - Cisco Systems[CODE]
View 7 Replies View RelatedCisco VPN :: 877 ADSL Router Which Won't Allow To Play With VPNs
May 20, 2011I have a Cisco 877 ADSL router which won't let me play with my VPNs like I used to in pre-Cisco days.I have a VPN server which resides on the inside of the network which used to get it's L2TP as well as PPTP tunnels passed straight through the ADSL router. No problems there with the old router.Now I opened the relevant ports for both TCP and UDP on the 877, but VPN simply won't establish when trying to connect from the outside. Process of getting the 877 to stop wanting to take charge of things VPN and just pass them off to an inside server?
I need to VPN into my work from my laptop on the private side of the 877. This works fine until after authentication, then the VPN connection goes silent, no traffic going through. Works fine when for instance using my iphone hotspot to connect through from my laptop. It's only not working when the 877 is in the equation.
Cisco WAN :: 2811 Router - ADSL Links
Jul 18, 2012can a Cisco 2811 router bundle 2 or 4 ADSL lines ? Reason am asking, we need a device that would be able to bundle 2 or 4 ADSL lines from ISP so that we can you it as backup link in-case the company Internet link does down.
View 5 Replies View RelatedCisco WAN :: 3845-2 - IPSEC From Behind ADSL Modem
Apr 9, 2013I'm trying to set up an IPSec tunnel between 2 3845 routers that each sit in a private LAN behind an ADSL modem. Each modem does have a static public IP address from the ISP.
Thus:
Cisco 3845-1 <-> ADSL modem <-> WAN <-> ADSL modem <-> Cisco 3845-2
3845-1
Gi 0/0 - private ip
l
NAT
[code]....
So I would like to set up IPSEC between the GI 0/0 interfaces on the 3845's.
Cisco WAN :: 2651XM ADSL - No Access To Configurations
Feb 21, 2012We have a number of 2651XM with WIC-1ADSL. These are supplied by another company and we do not have access to the configs.We are told that the maximum througput from the ADSL WIC to the FastEthernet 0/1 is 2.5Mbps ( "it's a backplane issue" ), even though the ADSL speed reported by the router on the external interface is 8MbpsT
View 3 Replies View RelatedCisco WAN :: 870 - Setup Router For ADSL Connection?
Nov 9, 2011I have reset the router of Cisco 870. I need to connect the router for ADSL connection but don't know how to do it.
[code]...
Cisco WAN :: Cannot Find ADSL Firmware 4.0.0.18 For 1801
Feb 25, 2010I have a number of Cisco 1801 routers connected to BT UK’s ADSL2+ Annex-A Wholesale Broadband Connect [WBC] services. The routers are experiencing connectivity issues. There is a cisco product bulletin that defines v4.0.0.18 as the version of ADSL Firmware required on the Cisco 1801 when connecting to this BT service.I would like to upgrade the ADSL Firmware for these routers but I cannot find v4.0.0.18 for the Cisco 1801 on CCO. All the 4.0.0.18 downloads appear to be for various flavours of 800. The Cisco product bulletin shows the 1801 as having the same chipset as the 857,867,877 and 887. Can I use the Firmware from one these 800 models? The MD5 Hash for the code suggests all of the these 800 model use the same code?
View 12 Replies View RelatedCisco WAN :: Apply QoS LLQ To 1721 ADSL Interface
Apr 17, 2007I can not apply the LLQ to ADSL ATM interface. the system take the command with out any error message, but no in the show running config. Any Cisco link can explain this? [code]
View 2 Replies View RelatedCisco WAN :: 2811 Using Sub-interfaces And PPPOE On ADSL
Apr 26, 2013I am trying to get my Cisco 2811 to authenticate four DSL connections and load balance them by attaching the four DSL to a switch (each DSL going to a seperate VLAN) and then trunking all four VLAN's to a ethernet interface on the 2811. My issue, I can not get more than one DSL to authenticate at a time, for example Dialer1 will connect and then it will disconnect and Dialer2 will connect, etc... I have the modems in bridge mode and I am using seperate user/pass for each DSL account and I have verified that the user/pass are correct.
Below is my config from the router and a couple of messages that came across the console.
*Apr 27 01:12:11.915: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di1
*Apr 27 01:12:11.927: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to down
[Code].....
Cisco WAN :: Configuring HWIC To ADSL In 1841
May 10, 2011I have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies View RelatedCisco WAN :: 1700 And ADSL Modem Connection
Oct 23, 2012I have an 1700 cisco Router and a ADSL connection to Internet.How may I use it on my home network?There's any configuration that I should to do?
View 3 Replies View RelatedCisco WAN :: 887VA - How To Change Adsl Mode
Jun 13, 2012In 12.x I used to go under atm0 and used ' dsl operating-mode' How can I do it under 887VA running 15.2?
View 1 Replies View Related
