Cisco WAN :: 827 ADSL Router IOS Upgrade?
May 5, 2013
My professor have asked us to do an IOS upgrade for a Cisco 827 ADSL Router. But I´am having problems to find the appropiate IOS image. The router original IOS is c827-y6-mz.121-1.XB and it supports routing protocols like rip bgp eigrp ospf is-is, etc.
Now, we have to find a newer IOS release that supports the same amount of routing protocols. This Router has only 24 MB DRAM and 8 MB Flash. We have tried with a IP PLUS/FW/IPSEC release 12.3(26) but when I write : route ? it only shows eigrp, odr and rip.
I am searching for a newer release that fits in those 24 MB and which has the other need routing protocols like ospf,bgp, etc.
an IOS image that meets what I am searching for?
View 1 Replies
ADVERTISEMENT
May 17, 2010
I cannot find instructions on how to use the latest 4.0.18 ADSL firmware on an 887 router.
I've downloaded adsl_alc_20190_4.0.018.bin from the website and copied it to flash, but cannot find any instructions on applying the firmware. Tried rebooting but made no difference.
What commands, etc, am I meant to use to make use of this ADSL firmware release ?
View 5 Replies
View Related
Aug 24, 2012
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies
View Related
Aug 1, 2011
I am installing a Cisco 887 to a ADSL2 Circuit and I cannot connect to the ADSL eventhough the show interface shows that both the ATM0.1 and Dialler 0 is up.
The configuration of the router is below.
Building configuration...
Current configuration : 5980 bytes
!
! Last configuration change at 11:12:58 PCTime Wed Aug 3 2011 by cisco
[Code].....
View 9 Replies
View Related
Mar 24, 2013
does Cisco 877 router support DSL (not ADSL?). i have tried connecting a dsl line and cant get ATM interface to come up - username and password are correct.alternative option: Can i get cisco 877 to form a ipsec tunnel using LAN port (not dialer interface) ? basically i want this 877 to act like asa 5505 where i can connect a LAN cable coming out from DSL router?
View 3 Replies
View Related
Jan 28, 2012
I would like to configure cisco 891 behind an ADSL Router(ISP one).The Details are:
ADSL Router:
- DSL Connection: dynamic IP
- LAN: 10.153.66.1/255.255.255.128
CISCO 891
- WAN: 10.153.66.5/255.255.255.128
- LAN: 10.153.64.1/255.255.255.128
- Configuration:
WAN
interface FastEthernet8
description Singtel Line$ETH-WAN$$FW_OUTSIDE$
ip address 10.153.66.5 255.255.255.128
[code]....
I could ping to 10.153.66.1(ADSL Router), but I cannot connect to the internet.
View 4 Replies
View Related
May 16, 2013
I have a bit of an issue setting up an Cisco 837/SOHO ADSL Router.
Basically what it is is that my Broadband router isnt doing its job very well, and the last piece of the puzzle in the server area is to upgrade the router, and I have with this. Now. I hve followed the setups as per cisco's guidlines very well and doen alot of research on the CLI commands, I have access to the router and have setup the system.
My broadband in the office is Orange/EE and its PPPoA. I hvae all the settings, and such and have followed a set of commands that apply to BT broadband but, It simply hasnt worked in my case. Any CLI commands to setup this router so i'll replace my business livebox.
View 7 Replies
View Related
Mar 22, 2011
The PPPoE connection can be successfully established only if the PC dials up, but not if the router replaces the PC to do so.Both the PC and the router are identically configured for this purpose, i.e. using the same ADSL dial-up account(usr/passwd pair). As a whole, we can exclude any wrong configuration on the router itself.
View 3 Replies
View Related
Jul 23, 2011
We want to use two isp connections in same server is it possiable. if adsl router has two rj 11 port's then we can use this is .
View 1 Replies
View Related
Nov 18, 2012
While i was looking around in my stuff in the office i have found a Cisco 877W ADSL router .. so i have decided to use it instead of the one i am using now which is provided by the ISP that's made by Huawei.Anyway i have a good knowledge about basic cisco router configuration but i had never configured ADSL Cisco router, so i looked around on Cisco website, and i was lucky to get this two linksCisco DSL Router Configuration and Troubleshooting Guide - Step-by-Step Configuration of PPPoA with a Dynamic IP Address - Cisco Systems[CODE]
View 7 Replies
View Related
May 20, 2011
I have a Cisco 877 ADSL router which won't let me play with my VPNs like I used to in pre-Cisco days.I have a VPN server which resides on the inside of the network which used to get it's L2TP as well as PPTP tunnels passed straight through the ADSL router. No problems there with the old router.Now I opened the relevant ports for both TCP and UDP on the 877, but VPN simply won't establish when trying to connect from the outside. Process of getting the 877 to stop wanting to take charge of things VPN and just pass them off to an inside server?
I need to VPN into my work from my laptop on the private side of the 877. This works fine until after authentication, then the VPN connection goes silent, no traffic going through. Works fine when for instance using my iphone hotspot to connect through from my laptop. It's only not working when the 877 is in the equation.
View 0 Replies
View Related
Jul 18, 2012
can a Cisco 2811 router bundle 2 or 4 ADSL lines ? Reason am asking, we need a device that would be able to bundle 2 or 4 ADSL lines from ISP so that we can you it as backup link in-case the company Internet link does down.
View 5 Replies
View Related
Nov 9, 2011
I have reset the router of Cisco 870. I need to connect the router for ADSL connection but don't know how to do it.
[code]...
View 2 Replies
View Related
May 26, 2013
I have a Cisco 2811 router with 2 ADSL interfaces and we have 2 internet lines associated with it. One is with Telstra and one is with iiNet. All internet traffic from inside the office is routed through Telstra line. The iiNet line is used for incoming emails, establishing VPN etc. The problem is that we are not able to "PING" the iiNet's IP address from the outside world however, PING works for Telstra IP. What do I need to configure on the router if I want to PING and Putty in the router using both Telstra's and iiNet's IP from outside world?
View 1 Replies
View Related
Apr 2, 2012
configuring my new Cisco 881 Router with my existing ADSL modem.At the moment, i am connecting to the internet using tp-link modem router, all PPPoE/DHCP/Wireless is set up there...and that connect to the switch where all my computer connected to.
Now i want to connect this new Cisco Router to it to basically do the firewall/filtering/dhcp...leave the authentication thing on my Modem.Can i get a head start what to configure here on the cisco? since it does not work as easily as other Router where I can just plug a cable from modem LAN to Router LAN.
View 2 Replies
View Related
Jan 5, 2012
My Internet speed slows down from about 4mpbs to 1mpbs approx until I reboot after which it runs fine until it slows down again.I have a Netgear DGN2000 router, and have tried restoring to factory settings and using it that way - made no difference.
View 1 Replies
View Related
Oct 9, 2012
I want to transfer files between two computers.i have a Router+Adsl modem i want to network two pc one is running windows xp and other is running windows 7.i plug both pc's cable in Router and LAN card...after that my network places shows below picture i didn't configure anything. url...when i click other network pc it ask me user name and password. url...I never did networking. how can i transfer files between two pc's while internet don't stop.
View 2 Replies
View Related
Dec 27, 2011
[code] My connection is ADSL with 2Mbps broadband. Using speedtest.net for testing the speed I got almost 2Mbps, that is ok, but this is connected directly to the modem. The problem is when I use the router, when I connect it the speed downs onward until it achieve a stable value of 512kbps, that is 4 times less than my contracted speed. I have tried with four different D-Link routers (DIR-280, DIR-600, DIR-600 N150, DIR-615), four ones give the same problem.D-Link tech support people don't have idea about what is happening just like tech support people from my Internet provider. I think the problem is not the modem because I get 2Mbps from it connected directly (without the router).I do the speed test in an interval of 3 minutes between each test, with just one device connected and only doing the speed test, all programs that use Internet access are closed.
Always is the same, after a time the speed drops down, from 2Mbps until 512kbps. The router has the QoS disabled, I have tried changing the MTU value, I have tried some values 1492 (this is the official from the Internet provider), also I have tried some lower numbers 1400, 1200 but the result is the same. The router has as security only wpa2 and it has a static public IP, the modem is configured as bridge. I have also tried unplugging the phones, connected to the splitter, keeping away the wireless phones, moving away the router from the modem for electronic interference, modifying the WAN speed from auto to 10 and 100, I have disabled the firewall, change the channels and power TX. I do the speed tests using the wireless and wired interfaces.
View 3 Replies
View Related
Oct 17, 2011
if I have made a simple mistake with my config. It has authenticated ok and been assinged an Internet IP address from the ISP but the clients can not connect ping any internet address nor can the router.
hostname
!boot-start-markerboot-end-marker!!enable secret 5 $1$WGr1$khNrjiwYANhUsIaKEBDsL0enable password 7 121A0C041104!no aaa
[Code].....
View 6 Replies
View Related
Apr 8, 2013
I have a 857w adsl router, I have configured it to connected to my ISP and i get a dhcp address from them, and I have dhcp pool to assign ip addresses to wireless or LAN, i have nat overload on a BVI . I am now trying to get one of the LAN port which has a device of 172.16.0.3 to be accessible from the outside world, but it will not let anyone connect to it.
View 9 Replies
View Related
Sep 14, 2011
Have an ADSL router (887) at a site which has a GRE tunnel to to a 3745.The GRE tunnel is setup with default ip mtu of 1476.If I ping from the 3745 to the ADSL router (or in the reverse direction)with a packet size of 1500 bytes this works fine.However if I ping from a router (R1) that is directly connected to 3745 to the ADSL router with a pkt size of1500 bytes then the first ping succeeds while the subsequent pings fail.Pkt sizes less than or equal to 1476 work okay.Pinging between R1 and the 3745 with a packet size of 1500 bytes works fine.If I set the tunnel ip mtu size to 1500 bytes then it works.This is obviously something to do with fragmentation, but I don't undertsand why itdoesn't work with the default mtu set to 1476.
View 11 Replies
View Related
Feb 21, 2013
I have a RV082 VPN Router. But my internet connection is ADSL brodband. How can i connect and setup a VPN connection to other RV082.
View 1 Replies
View Related
Mar 6, 2012
what will be the work around on this configuration.currently we have a Lease Line connection on serial interfaceISP <=SERIAL=>Router 2911<=ACCESS MODE=>Firewall(DATA DHCP SERVER located here, policy implemented here)<=TRUNK MODE=>CORE Switch(VLAN Assignment is here)<=TRUNK MODE=>ACCESS Switch(DATA and VOICE passess thru each ports)i am thinking to create a DHCP pool on the router to where my firewall should point to and from the DHCP pool it will point the internal network going to public network.
View 2 Replies
View Related
Jul 7, 2011
I have been trying to connect a new Cisco 887VA Router to the Internet using ADSL via PPPoE and have been unsuccessful. The DSL line is active and functioning correctly since the current "old" router is connected and working without any problems (the "old" DLink router is connected to an Alcatel DSL Modem). AT&T provides the ADSL service to the office. When the Cisco Router is connected it tries to negotiate a connection via PPPoE on the WAN interface but utlimately fails. The IP for the WAN interface is dynamic.
Below is the current configuration of the router.
!
! Last configuration change at 00:43:54 UTC Sun Jun 26 2011
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]....
View 9 Replies
View Related
Jun 18, 2012
i have ASA 5505 and have a ADSL modem (hwich has DHCP enabled) 192.168.1.X/24....i have static ip as well which is 34.X.X.X. i want to use ASA as a firewall and want to make site to site VPN..i tried to google it but i cant find any config.i have 4 swicth port in the ADSL modem so shd i connect my ASA with building switch but then it will have DHCP enabled if i disable DHCP on ADSL router then how will my ASA communicate.
View 1 Replies
View Related
May 3, 2013
I m getting the below debug log and can not get IP from my ISP. It is static IP address and there is modem in bridge mode for the adsl line.
Below Conf and debug out put,interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
end
[Code]....
View 3 Replies
View Related
Dec 9, 2012
i have one airtel isp connection was connected to beetel adsl modem and this modem is connected to d-link switch to accessing internet for my lan. and one netgear wireless router is aslo connected to this d-link switch. my need is i has one cisco 1900 router, i want to get internet access from adsl modem or netgear router to my cisco router.
View 1 Replies
View Related
Mar 15, 2011
we have cisco sr520 adsl router at one of the sites. A device is connected to the LAN and needs to be communicated directly to the server with 3rd party over internet. we have a static public IP( a.b.c.d) for cisco router and want this IP redirected to the LAN IP address(192.168.1.20) of the device but locked to only 2 inbound IP address (eg.-1.2.3.4 , 5.6.7.8) .
View 1 Replies
View Related
Jan 18, 2013
I'm trying to relace my isp modem by a cisco 877 adsl router..
The internet part is already done is working fine... however... there is also an seperate pvc for the voice part.
The pvc is working with the MER protocol... the thing now is... when i'm trying to get an ip address by dhcp on the sub atm interface nothing happen..
I did an debug dhcp detail and see that the router is first sending correctly an dhcp discover,the isp is replying to this with an dhcp offer i see my ip address,subnet mask and gateway addresses however.. the router isn't replying anymore with an dhcp request... so nothing happens anymore..
View 1 Replies
View Related
Nov 20, 2011
A Layer 2 switch with IP Address 192.168.1.4 (Vlan0), subnet 255.255.255.0 is physically connected to ADSL Router with IP address 192.168.1.1 (which is also the gateway address for the switch). The problem I have is that all the devices connected to the switch can intercommunicate but are unable to communicate with devices connected to the Router. I guess this may be something to do with how the Vlan is configured on ADSL router?
View 1 Replies
View Related
Feb 11, 2011
in my past days i am using bsnl broadband. and also using adsl router for net-connection. i am connecting internet through wifi adsl router. now i am not using bsnl broadband. now i am using beem broadband in hyderabad. that internet connection is directly to my laptop through rj45 cable. but i want to configure adsl router to my beem broadband because i want to connect internet through wifi.it is possible or not? if possible tell me the procedure.
View 2 Replies
View Related
Feb 22, 2013
My desktop however, does not have built-in wireless and therefore would have to connect to the ADSL router (Netgear) through ethernet but this cannot be done as the router must remain in my bedroom, much too far away for cables to reach.I bought a USB wireless connecter for the desktop but it doesn't seem to work. It connects but gives "Local Only" as the connection.
View 9 Replies
View Related
Nov 22, 2011
I am looking to purchase an ADSL wireless modem router combo which will be mainly used for net browsing, online gaming (ps3) and skype.It has been suggested by the IT tech we use that I a get dual band n wireless gigabit modem/router but my limited knowledge and the confusion created by reading multiple contracting reviews of products is sending me a bit loopy.
View 2 Replies
View Related
