I am installing a Cisco 887 to a ADSL2 Circuit and I cannot connect to the ADSL eventhough the show interface shows that both the ATM0.1 and Dialler 0 is up.
The configuration of the router is below.
Building configuration...
Current configuration : 5980 bytes
!
! Last configuration change at 11:12:58 PCTime Wed Aug 3 2011 by cisco
[Code].....
I would like to configure cisco 891 behind an ADSL Router(ISP one).The Details are:
ADSL Router:
- DSL Connection: dynamic IP
- LAN: 10.153.66.1/255.255.255.128
CISCO 891
- WAN: 10.153.66.5/255.255.255.128
- LAN: 10.153.64.1/255.255.255.128
- Configuration:
WAN
interface FastEthernet8
description Singtel Line$ETH-WAN$$FW_OUTSIDE$
ip address 10.153.66.5 255.255.255.128
[code]....
I could ping to 10.153.66.1(ADSL Router), but I cannot connect to the internet.
While i was looking around in my stuff in the office i have found a Cisco 877W ADSL router .. so i have decided to use it instead of the one i am using now which is provided by the ISP that's made by Huawei.Anyway i have a good knowledge about basic cisco router configuration but i had never configured ADSL Cisco router, so i looked around on Cisco website, and i was lucky to get this two linksCisco DSL Router Configuration and Troubleshooting Guide - Step-by-Step Configuration of PPPoA with a Dynamic IP Address - Cisco Systems[CODE]
View 7 Replies View Relatedin my past days i am using bsnl broadband. and also using adsl router for net-connection. i am connecting internet through wifi adsl router. now i am not using bsnl broadband. now i am using beem broadband in hyderabad. that internet connection is directly to my laptop through rj45 cable. but i want to configure adsl router to my beem broadband because i want to connect internet through wifi.it is possible or not? if possible tell me the procedure.
View 2 Replies View RelatedI want to setup secure Wi-Fi on my Beetel ADSL modem/router. What are the parameters which I need to setup through the modem web interface?
View 1 Replies View RelatedI have this adsl wireless router but my internet connection only has RJ45 directly connected to my PC. My questions is how can I use my ADSL wireless router with this kind of internet connection.. because I really want to make my connection wireless..
View 1 Replies View Relatedi have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedI need to configure ADSL on my 837 Router with simple configuration. The WAN IP address is dynamic from my ISP. I checked many websites and found different configurations everywhere. I don't know which is best suited for me. I used SDM and configured ADSL. When i checked the configuration from console i found that there is atm0.2 and dialer 2 configured with my settings. I cannot understand what is the purpose of atm0.2 and dialer 2 when atm0 and dialer0 are there. Is there a doc on ADSL config on 837?
interface Ethernet0 ip tcp adjust-mss 1412 exitinterface ATM0.2 point-to-point no shutdown pvc 0/35 pppoe-client dial-pool-number 1 exit exitinterface Dialer2 exitdefault interface Dialer2interface Dialer2 ip mtu 1452 no shutdown ip address negotiated dialer pool 1 dialer-group 1 encapsulation ppp dialer idle-timeout 120 dialer fast-idle 20 ppp authentication chap pap callin ppp pap sent-username username ppp chap password 0 password exitdialer-list 1 protocol ip permit
I am configuring a 1841 router for use in small out office. I will use the s0/0/0 for main WAN T1 connection. I then wanted to use the ATM0/1/0 WIC-1-ADSL card as a failover. I am using weighted static routes for failover. Fe0/0 is LAN interface. When I go into SDM and look at the ATM interface it says this configuration is unsupported?
1. Can't I just get a DSL modem and connect it to fe0/1 and not use ATM WIC and use below for failover?
2. If I have to use ATM WIC what needs to be configured for it to work with Att aDSL?
I have a Cisco 1841 router with an HWIC-ADSL module installed. My ADSL connection is PPPoA with a dialer interface and I have been provided 6 ip's from my provider to use on this service. Previously I have connected Fa0/0 on the 1841 straight onto my network and used NAT and ACL's on the 1841, I would now like to change this and have Fa0/0 connected to a Palo Alto firewall and use the Palo Alto to provide NAT, Firewall & site to site VPN functions. What config would I require on the 1841 to allow me to use one of my ISP IP addresses on the Palo Alto to allow it to be a VPN endpoint? Do I need to configure the 1841 in bridge mode?
View 3 Replies View RelatedI have an ADSL connection which I would like to have my Cisco Soho 97 ADSL router configured to dialup and forward to port 8080.
My network is 192.168.1.0/24
Router is 192.168.1.1
Server is 192.168.1.4 - Default gateway is 192.168.1.1
I am able to connect using the script below and get a public ip address but i cant get it to connect to the internet?what command to use for port forwarding to 8080?
hostname Router
!
!
ip subnet-zero
ip name-server 212.23.8.1
ip name-server 212.23.3.1
ip dhcp excluded-address 192.168.1.1
[code]...
I have configure 887 ADSL router with attached configuration. But users cant access internet properly. (Ex: yahoo and gmail mail cant access)
View 8 Replies View RelatedI am trying to configure a Cisco 1841 to allow the users to access the internet. This is my first step with ppp. All the rest of the configuration is ok but I don't know how to setup the interfaces Dialer0 and ATM0/0/0.
Need very basic configuration that I can analyze and use on my device?
i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.
View 9 Replies View RelatedRegion : Brazil
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : Telemar Oi Velox
Very weird situation... can't get full speed with the TD-W8968 with my DSL link..
I have one of my customer have cisco 2951 Router with two ISP and two ADSL module .i already configure one ADSL module.rit now customer want secondISP ( ADSL) module configuration separate netwok because customer have Access pont they want connect directly to router is it possible
1st ISP already running but customer requirement 2nd ISP superate network with Access pont not redundancy
correct settings > Configuration of WAG54G2 on etisalat adsl fiber optic
View 1 Replies View Relateddoes Cisco 877 router support DSL (not ADSL?). i have tried connecting a dsl line and cant get ATM interface to come up - username and password are correct.alternative option: Can i get cisco 877 to form a ipsec tunnel using LAN port (not dialer interface) ? basically i want this 877 to act like asa 5505 where i can connect a LAN cable coming out from DSL router?
View 3 Replies View RelatedMy professor have asked us to do an IOS upgrade for a Cisco 827 ADSL Router. But I´am having problems to find the appropiate IOS image. The router original IOS is c827-y6-mz.121-1.XB and it supports routing protocols like rip bgp eigrp ospf is-is, etc.
Now, we have to find a newer IOS release that supports the same amount of routing protocols. This Router has only 24 MB DRAM and 8 MB Flash. We have tried with a IP PLUS/FW/IPSEC release 12.3(26) but when I write : route ? it only shows eigrp, odr and rip.
I am searching for a newer release that fits in those 24 MB and which has the other need routing protocols like ospf,bgp, etc.
an IOS image that meets what I am searching for?
I have a bit of an issue setting up an Cisco 837/SOHO ADSL Router.
Basically what it is is that my Broadband router isnt doing its job very well, and the last piece of the puzzle in the server area is to upgrade the router, and I have with this. Now. I hve followed the setups as per cisco's guidlines very well and doen alot of research on the CLI commands, I have access to the router and have setup the system.
My broadband in the office is Orange/EE and its PPPoA. I hvae all the settings, and such and have followed a set of commands that apply to BT broadband but, It simply hasnt worked in my case. Any CLI commands to setup this router so i'll replace my business livebox.
The PPPoE connection can be successfully established only if the PC dials up, but not if the router replaces the PC to do so.Both the PC and the router are identically configured for this purpose, i.e. using the same ADSL dial-up account(usr/passwd pair). As a whole, we can exclude any wrong configuration on the router itself.
View 3 Replies View RelatedWe want to use two isp connections in same server is it possiable. if adsl router has two rj 11 port's then we can use this is .
View 1 Replies View RelatedI have a Cisco 877 ADSL router which won't let me play with my VPNs like I used to in pre-Cisco days.I have a VPN server which resides on the inside of the network which used to get it's L2TP as well as PPTP tunnels passed straight through the ADSL router. No problems there with the old router.Now I opened the relevant ports for both TCP and UDP on the 877, but VPN simply won't establish when trying to connect from the outside. Process of getting the 877 to stop wanting to take charge of things VPN and just pass them off to an inside server?
I need to VPN into my work from my laptop on the private side of the 877. This works fine until after authentication, then the VPN connection goes silent, no traffic going through. Works fine when for instance using my iphone hotspot to connect through from my laptop. It's only not working when the 877 is in the equation.
can a Cisco 2811 router bundle 2 or 4 ADSL lines ? Reason am asking, we need a device that would be able to bundle 2 or 4 ADSL lines from ISP so that we can you it as backup link in-case the company Internet link does down.
View 5 Replies View RelatedI have reset the router of Cisco 870. I need to connect the router for ADSL connection but don't know how to do it.
[code]...
I have a Cisco 2811 router with 2 ADSL interfaces and we have 2 internet lines associated with it. One is with Telstra and one is with iiNet. All internet traffic from inside the office is routed through Telstra line. The iiNet line is used for incoming emails, establishing VPN etc. The problem is that we are not able to "PING" the iiNet's IP address from the outside world however, PING works for Telstra IP. What do I need to configure on the router if I want to PING and Putty in the router using both Telstra's and iiNet's IP from outside world?
View 1 Replies View RelatedI cannot find instructions on how to use the latest 4.0.18 ADSL firmware on an 887 router.
I've downloaded adsl_alc_20190_4.0.018.bin from the website and copied it to flash, but cannot find any instructions on applying the firmware. Tried rebooting but made no difference.
What commands, etc, am I meant to use to make use of this ADSL firmware release ?
configuring my new Cisco 881 Router with my existing ADSL modem.At the moment, i am connecting to the internet using tp-link modem router, all PPPoE/DHCP/Wireless is set up there...and that connect to the switch where all my computer connected to.
Now i want to connect this new Cisco Router to it to basically do the firewall/filtering/dhcp...leave the authentication thing on my Modem.Can i get a head start what to configure here on the cisco? since it does not work as easily as other Router where I can just plug a cable from modem LAN to Router LAN.
My Internet speed slows down from about 4mpbs to 1mpbs approx until I reboot after which it runs fine until it slows down again.I have a Netgear DGN2000 router, and have tried restoring to factory settings and using it that way - made no difference.
View 1 Replies View RelatedI want to transfer files between two computers.i have a Router+Adsl modem i want to network two pc one is running windows xp and other is running windows 7.i plug both pc's cable in Router and LAN card...after that my network places shows below picture i didn't configure anything. url...when i click other network pc it ask me user name and password. url...I never did networking. how can i transfer files between two pc's while internet don't stop.
View 2 Replies View Related[code] My connection is ADSL with 2Mbps broadband. Using speedtest.net for testing the speed I got almost 2Mbps, that is ok, but this is connected directly to the modem. The problem is when I use the router, when I connect it the speed downs onward until it achieve a stable value of 512kbps, that is 4 times less than my contracted speed. I have tried with four different D-Link routers (DIR-280, DIR-600, DIR-600 N150, DIR-615), four ones give the same problem.D-Link tech support people don't have idea about what is happening just like tech support people from my Internet provider. I think the problem is not the modem because I get 2Mbps from it connected directly (without the router).I do the speed test in an interval of 3 minutes between each test, with just one device connected and only doing the speed test, all programs that use Internet access are closed.
Always is the same, after a time the speed drops down, from 2Mbps until 512kbps. The router has the QoS disabled, I have tried changing the MTU value, I have tried some values 1492 (this is the official from the Internet provider), also I have tried some lower numbers 1400, 1200 but the result is the same. The router has as security only wpa2 and it has a static public IP, the modem is configured as bridge. I have also tried unplugging the phones, connected to the splitter, keeping away the wireless phones, moving away the router from the modem for electronic interference, modifying the WAN speed from auto to 10 and 100, I have disabled the firewall, change the channels and power TX. I do the speed tests using the wireless and wired interfaces.
if I have made a simple mistake with my config. It has authenticated ok and been assinged an Internet IP address from the ISP but the clients can not connect ping any internet address nor can the router.
hostname
!boot-start-markerboot-end-marker!!enable secret 5 $1$WGr1$khNrjiwYANhUsIaKEBDsL0enable password 7 121A0C041104!no aaa
[Code].....
I have a 857w adsl router, I have configured it to connected to my ISP and i get a dhcp address from them, and I have dhcp pool to assign ip addresses to wireless or LAN, i have nat overload on a BVI . I am now trying to get one of the LAN port which has a device of 172.16.0.3 to be accessible from the outside world, but it will not let anyone connect to it.
View 9 Replies View Related