The PPPoE connection can be successfully established only if the PC dials up, but not if the router replaces the PC to do so.Both the PC and the router are identically configured for this purpose, i.e. using the same ADSL dial-up account(usr/passwd pair). As a whole, we can exclude any wrong configuration on the router itself.
View 3 RepliesI've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
I'm trying to get a solution together for a dial backup to an ADSL service, using an Analogue modem.The kit list is as follows:
Cisco 877
Multitech MT5656ZDX External Analogue Modem or USR 5630D External Analogue Modem
Rolled patch cable RJ45 to DB25M adapter (pinout from a cisco guide)
So far I am unable to get the router/modem to dial out at all. I know the modems work, I have tested them from Windows.
I have attached a couple of outputs from "show line" and "show line 1" from the router and also what I think are the relevent lines of config although it will be too much config and probably jumbled by now as I've tried quite a few things to try and get this working.
I am more concerned with the config relating to the connection of the analogue modem than the routing element.
I need to purchase an 64K dial up modem or a 64K dial up external adapter
View 1 Replies View Relatedi have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View Relatedcan i use a AT&T Router for dial up
View 1 Replies View RelatedI have an HP desktop and an Acer Aspire 16" laptop that I have had for 2 years. The laptop has built in WiFi, but luckily has a 56k modem also. Now for the problem....Saturday my husband bought me a wireless Velocity Cruz 7" color Tablet. I has been told in the past that all I had to do was buy a wireless router and plug it into the phone line. But today I called both Radio Shack and Office Max and asked if you could hook up a wireless router to dialup and both places told me absolutely not because dialup was too slow.
View 1 Replies View RelatedI have a cisco 1941 ISR router and I am trying to configure a router to allow a modem for "Offband or Out of band" access.Below is the configuration on Aux port on Line (n):
line aux 0
login local
modem InOut
transport input all
speed 115200
flowcontrol hardware
I have US Robotics 56k Faxmodem which is connected to aux port of router and I am using USB dialup modem with my laptop to dailin to the router which is connected to a US Robotics Faxmodem. Then I have accessed my USB dialup modem throught HyperTerminal and I can issue all "at" commands and to dialin to the modem I have used the following command atdt914011111111 (atdt followed by country code, area code and landline number)Once I issue the above command it give me message "Connected" and after this I just get a flashing cursor. I cannot do anything nor will it display a username login prompt.
Can I connect a router to a dial up connection and get wi-fi?
View 2 Replies View RelatedI have cable broadband internet.My internet modem is a Ubee D3.0.It is connected to my Netgear N600 Wifi router which have my computer and DirecTV hooked up to it via Ethernet.My wifi went down the other day.Devices were connected, but were not getting any internet service.In troubleshooting, I attempted to dial in to the router using url... as well as 192.168.0.1, and I could not get into the router.I assumed the router must have crashed, and I only purchased it a month ago, so I took it back to the store and exchanged it for a new one.I got home and plugged it in, still not working.I can't access it using the above mentioned methods, and the setup software does not detect a router present.I unplugged the router and hooked the computer up directly to the internet modem.Still no luck.The computer does show a network connection in the system tray, but with no internet.I plugged my laptop in to the internet modem, and I am able to get internet just fine from my laptop. even did a system restore to a restore point last week when I know the internet was working..
View 5 Replies View RelatedI have cable broadband internet. My internet modem is a Ubee D3.0. It is connected to my Netgear N600 Wifi router which have my computer and DirecTV hooked up to it via ethernet. My wifi went down the other day. Devices were connected, but were not getting any internet service. In troubleshooting, I attempted to dial in to the router using www.routerlogin.net as well as 192.168.0.1, and I could not get into the router. I assumed the router must have crashed, and I only purchased it a month ago, so I took it back to the store and exchanged it for a new one. I got home and plugged it in, still not working. I can't access it using the above mentioned methods, and the setup software does not detect a router present. I unplugged the router and hooked the computer up directly to the internet modem. Still no luck. The computer does show a network connection in the system tray, but with no internet. I plugged my laptop in to the internet modem, and I am able to get internet just fine from my laptop. I even did a system restore to a restore point last week when I know the internet was working. No luck.
View 5 Replies View Relatedwhat or where is the ethernet port
View 1 Replies View RelatedThe servers are calibrated to allow this, however I'm not sure how to connect from my end. I have an assignment where I have to dial into both a Windows server and an Ubuntu server to conduct some tasks (the actual process of dialing into the servers is not part of the assignment). I've been given the username, password, IP address, and protocol for each server. However, I cannot figure out how to use these to "dial into" them.I am running Windows 7 on a wireless connection
View 6 Replies View RelatedMy wifes Wifi is down. Need to connect to AOL via dial up.How can I get to internet to do so.
View 1 Replies View RelatedMy HP home vista keeps on disconnecting.I use dial up. The IPS service provider said to plug the computer directly into the phone jack without using the splitter which is a plug that has two openings(1 for phone and 1 for the computer in the event that the splitter is bad) I tried this and as soon as a connection is made about a minute later I'm disconnected again. Any ideas as how to resolve this problem? Also I was told that if I have DSL that this wouldn't be a problem
View 9 Replies View RelatedI have two pcs not connected other than keyboard and monitor. Both have identical USB dial up modems. I PC running Windows XP connects every time, the other running Windows 2000 connects only sometimes. Like this morning it connected on the third attempt and I was able to move a lot of files. When I tried again later I got five attempts and then "no answer".
View 3 Replies View RelatedI moved to a remote area where I cannot get DSL or Broadband. I can however get Dial up, like earthlink and Netzero. Before I signup for one of these services, I would like to know if there is any way to make my dialup a wireless conection for my laptops. I like to move around using the computer, I hate being at a desk having to sit there and not be able to move where I want.I have a modem that I used for my old dsl connection. Will this work?
View 1 Replies View RelatedMy computer is Dell Inspiron530 w/32bit vista & 2.00gb. Is this ok for DSL?
View 3 Replies View RelatedI have a ventilation controller that connects using a phone line. I have do not have a second phone line to dial out with my computer. is there a way i could set up dialing via broadband?
View 2 Replies View Relatedi have one xp machine. i wnd to configure two different dial up connection in one xp machine for band width sharing.
View 1 Replies View RelatedWe want to use two isp connections in same server is it possiable. if adsl router has two rj 11 port's then we can use this is .
View 1 Replies View RelatedI believe that the Cisco Unified Communications Manager Express matches the outbound VoIP dial peer digit-by-digit, because:
1. when using the debug command it shows how it works digit-by-digit till it match a pattern
2. It says in the study guide ( If a match is found, the router immediately processes the call - chapter 6) so I understand its not en bloc
How i can create dial up connection i don't know to create?
View 1 Replies View RelatedI have a dlink DWA130 wireless N adapter connected and working. But AOL Dialup takes over. When disconnecting the phone line for AOL, there is no internet connection. The adapter is connected and has great signal strength. What can I do to make the wireless adapter work independently from AOL dialup?
View 3 Replies View RelatedI had a Sony Viao with Windows Vista for some years and I managed to create a bridge using the Sony Viao laptop and my o2 usb modem. That was some time ago and now I have a new laptop with Windows 7 ?I have to mention that I do not have wireless connections. I have an o2 modem and an ethernet cable. They are the only two connections that show up in my internet connections. The LAN connection has an image of a ethernet cable connection while the o2 connection has an image of a phone.whenever I watch youtube walk throughs it never looks like my set up. Ive tried everything over and over. Turning off UAC, turning on sharing but nothing has worked yet. When I just select the LAN connection and right click there is an option to Bridge. When I right click the o2 connection its not there. When I select both the option isnt there either.
View 2 Replies View RelatedI am without my connection until repairs are made inthe following week. I am trying to set up netzero with my current equipment, but cannot find the cd for my netgear router WNR1000.
View 1 Replies View RelatedBasically i need to test to see where the telephone lines are terminated, because when they where built into the walls the used standard cat5e cable to terminate it to an RJ-11 jack but over in the wiring panel it (i assume it is anyways) terminates to an RJ-45 jack but im not sure if this is really the cable for the telephone or something else, so i have a phone connected to the wall jack and a computer on this end and i would like to send a dial tone or any tone in general that the phone can pickup.
View 3 Replies View RelatedMy Internet speed slows down from about 4mpbs to 1mpbs approx until I reboot after which it runs fine until it slows down again.I have a Netgear DGN2000 router, and have tried restoring to factory settings and using it that way - made no difference.
View 1 Replies View RelatedI want to transfer files between two computers.i have a Router+Adsl modem i want to network two pc one is running windows xp and other is running windows 7.i plug both pc's cable in Router and LAN card...after that my network places shows below picture i didn't configure anything. url...when i click other network pc it ask me user name and password. url...I never did networking. how can i transfer files between two pc's while internet don't stop.
View 2 Replies View Related[code] My connection is ADSL with 2Mbps broadband. Using speedtest.net for testing the speed I got almost 2Mbps, that is ok, but this is connected directly to the modem. The problem is when I use the router, when I connect it the speed downs onward until it achieve a stable value of 512kbps, that is 4 times less than my contracted speed. I have tried with four different D-Link routers (DIR-280, DIR-600, DIR-600 N150, DIR-615), four ones give the same problem.D-Link tech support people don't have idea about what is happening just like tech support people from my Internet provider. I think the problem is not the modem because I get 2Mbps from it connected directly (without the router).I do the speed test in an interval of 3 minutes between each test, with just one device connected and only doing the speed test, all programs that use Internet access are closed.
Always is the same, after a time the speed drops down, from 2Mbps until 512kbps. The router has the QoS disabled, I have tried changing the MTU value, I have tried some values 1492 (this is the official from the Internet provider), also I have tried some lower numbers 1400, 1200 but the result is the same. The router has as security only wpa2 and it has a static public IP, the modem is configured as bridge. I have also tried unplugging the phones, connected to the splitter, keeping away the wireless phones, moving away the router from the modem for electronic interference, modifying the WAN speed from auto to 10 and 100, I have disabled the firewall, change the channels and power TX. I do the speed tests using the wireless and wired interfaces.
I am installing a Cisco 887 to a ADSL2 Circuit and I cannot connect to the ADSL eventhough the show interface shows that both the ATM0.1 and Dialler 0 is up.
The configuration of the router is below.
Building configuration...
Current configuration : 5980 bytes
!
! Last configuration change at 11:12:58 PCTime Wed Aug 3 2011 by cisco
[Code].....
does Cisco 877 router support DSL (not ADSL?). i have tried connecting a dsl line and cant get ATM interface to come up - username and password are correct.alternative option: Can i get cisco 877 to form a ipsec tunnel using LAN port (not dialer interface) ? basically i want this 877 to act like asa 5505 where i can connect a LAN cable coming out from DSL router?
View 3 Replies View RelatedMy professor have asked us to do an IOS upgrade for a Cisco 827 ADSL Router. But I´am having problems to find the appropiate IOS image. The router original IOS is c827-y6-mz.121-1.XB and it supports routing protocols like rip bgp eigrp ospf is-is, etc.
Now, we have to find a newer IOS release that supports the same amount of routing protocols. This Router has only 24 MB DRAM and 8 MB Flash. We have tried with a IP PLUS/FW/IPSEC release 12.3(26) but when I write : route ? it only shows eigrp, odr and rip.
I am searching for a newer release that fits in those 24 MB and which has the other need routing protocols like ospf,bgp, etc.
an IOS image that meets what I am searching for?