I have two pcs not connected other than keyboard and monitor. Both have identical USB dial up modems. I PC running Windows XP connects every time, the other running Windows 2000 connects only sometimes. Like this morning it connected on the third attempt and I was able to move a lot of files. When I tried again later I got five attempts and then "no answer".
View 3 RepliesI need to purchase an 64K dial up modem or a 64K dial up external adapter
View 1 Replies View RelatedIs it possible to run both LAN connection and dial-up modem for internet on the same system?
View 11 Replies View RelatedI have a cisco 1941 ISR router and I am trying to configure a router to allow a modem for "Offband or Out of band" access.Below is the configuration on Aux port on Line (n):
line aux 0
login local
modem InOut
transport input all
speed 115200
flowcontrol hardware
I have US Robotics 56k Faxmodem which is connected to aux port of router and I am using USB dialup modem with my laptop to dailin to the router which is connected to a US Robotics Faxmodem. Then I have accessed my USB dialup modem throught HyperTerminal and I can issue all "at" commands and to dialin to the modem I have used the following command atdt914011111111 (atdt followed by country code, area code and landline number)Once I issue the above command it give me message "Connected" and after this I just get a flashing cursor. I cannot do anything nor will it display a username login prompt.
My daughter is on an Army Base in the South Pacific. They have Dial up internet on their home telephone not DSL. They have high speed wireless at the base community center/coffee shop. I will be going there in 9 days to install the dir-615. She has a Dell Desktop with Vista Basic SP1, laptop with XP, IPAD2 and a NOOK Tablet. The dir-615 HVE1 with firmware 5.00na on the bottom sticker. She said she was able to go to web address, login, change the user name and password, started on the wireless configuration and she paniced. My question is basically this. by using a cat5 cable from the desktop to the dir-615 with dialup internet connected can the router be setup using the automatic method as opposed to manual. Our first priority is to be able transfer files to the 2 tablets without being connected to the internet like a switch and secondly If possible go on to the internet from a Tablet or the Laptop. I assume the second option would reuire internet sharing option when setting up the network and performance would be ugly.
Can get I get this router to work this way with just dialup to set it up
I'm trying to get a solution together for a dial backup to an ADSL service, using an Analogue modem.The kit list is as follows:
Cisco 877
Multitech MT5656ZDX External Analogue Modem or USR 5630D External Analogue Modem
Rolled patch cable RJ45 to DB25M adapter (pinout from a cisco guide)
So far I am unable to get the router/modem to dial out at all. I know the modems work, I have tested them from Windows.
I have attached a couple of outputs from "show line" and "show line 1" from the router and also what I think are the relevent lines of config although it will be too much config and probably jumbled by now as I've tried quite a few things to try and get this working.
I am more concerned with the config relating to the connection of the analogue modem than the routing element.
So I have a really neat computer sitting here, 2500K, P8z68-v, samsung 830 64gb ssd, corsair vengeance 16gb, deskstar hdd, firepro v5800
I have a non-descript trendnet 56K v.92 dial up modem installed to pci slot1 on my mobo.The phone company says they can't get a quicker connection than 31.2 Kbps established to dial up users in this area.The real issue is the data transfer rate.I have seen it reach as high as 6.xx Kbps but generally hovers around 2.5 Kbps.Now it is down to 1.xx Kbps and I took the last 48 hours downloading all the updates for windows and several other updates for hard ware etc.Now I need the ATI firepro update and 114 Mb will take over 16 hours at my average speed, and some 32 hours at the new slower speed
My wifes Wifi is down. Need to connect to AOL via dial up.How can I get to internet to do so.
View 1 Replies View RelatedI have an HP desktop and an Acer Aspire 16" laptop that I have had for 2 years. The laptop has built in WiFi, but luckily has a 56k modem also. Now for the problem....Saturday my husband bought me a wireless Velocity Cruz 7" color Tablet. I has been told in the past that all I had to do was buy a wireless router and plug it into the phone line. But today I called both Radio Shack and Office Max and asked if you could hook up a wireless router to dialup and both places told me absolutely not because dialup was too slow.
View 1 Replies View RelatedCan I connect a router to a dial up connection and get wi-fi?
View 2 Replies View RelatedI have cable broadband internet.My internet modem is a Ubee D3.0.It is connected to my Netgear N600 Wifi router which have my computer and DirecTV hooked up to it via Ethernet.My wifi went down the other day.Devices were connected, but were not getting any internet service.In troubleshooting, I attempted to dial in to the router using url... as well as 192.168.0.1, and I could not get into the router.I assumed the router must have crashed, and I only purchased it a month ago, so I took it back to the store and exchanged it for a new one.I got home and plugged it in, still not working.I can't access it using the above mentioned methods, and the setup software does not detect a router present.I unplugged the router and hooked the computer up directly to the internet modem.Still no luck.The computer does show a network connection in the system tray, but with no internet.I plugged my laptop in to the internet modem, and I am able to get internet just fine from my laptop. even did a system restore to a restore point last week when I know the internet was working..
View 5 Replies View RelatedWe are having dialup 15 connections in router 3845 model IOS version 12.4 1A.We are unable to have a connection between dialup branches to headquarter. these are the command
aaa new-model
!
!
aaa authentication login telnet local
aaa authentication login ppp local
aaa authentication ppp ppp local
[code].....
I just got a dir-655 revb, and it does not connect to the internet. I have DSL, and the old router works fine with PPPoE, when I configure my dir-655b router, it can not connect to the internet. I get the flowing error:
info Mar 23 22:31:11 rp_pppoe =' read pppoe_conn_session error or first time dial
notice Mar 23 22:31:10 pppd 2.4.3 started by root, uid 0
info Mar 23 22:31:10 RP-PPPoE plugin inform wantimer to reset auth, discovery variable
info Mar 23 22:31:10 RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3
info Mar 23 22:31:10 Plugin /lib/pppd/2.4.3/rp-pppoe.so loaded.
info Mar 23 22:31:05 Exit.
I have cable broadband internet. My internet modem is a Ubee D3.0. It is connected to my Netgear N600 Wifi router which have my computer and DirecTV hooked up to it via ethernet. My wifi went down the other day. Devices were connected, but were not getting any internet service. In troubleshooting, I attempted to dial in to the router using www.routerlogin.net as well as 192.168.0.1, and I could not get into the router. I assumed the router must have crashed, and I only purchased it a month ago, so I took it back to the store and exchanged it for a new one. I got home and plugged it in, still not working. I can't access it using the above mentioned methods, and the setup software does not detect a router present. I unplugged the router and hooked the computer up directly to the internet modem. Still no luck. The computer does show a network connection in the system tray, but with no internet. I plugged my laptop in to the internet modem, and I am able to get internet just fine from my laptop. I even did a system restore to a restore point last week when I know the internet was working. No luck.
View 5 Replies View RelatedMy Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies View RelatedI want to connect my tata photon device to my bsnl wifi modem via a usb portavailable on the bsnl modem. This is to provide a wifi network that i can use to surf the net on my phone.
View 4 Replies View RelatedI have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies View Relatedwhat or where is the ethernet port
View 1 Replies View RelatedThe servers are calibrated to allow this, however I'm not sure how to connect from my end. I have an assignment where I have to dial into both a Windows server and an Ubuntu server to conduct some tasks (the actual process of dialing into the servers is not part of the assignment). I've been given the username, password, IP address, and protocol for each server. However, I cannot figure out how to use these to "dial into" them.I am running Windows 7 on a wireless connection
View 6 Replies View Relatedcan i use a AT&T Router for dial up
View 1 Replies View RelatedMy HP home vista keeps on disconnecting.I use dial up. The IPS service provider said to plug the computer directly into the phone jack without using the splitter which is a plug that has two openings(1 for phone and 1 for the computer in the event that the splitter is bad) I tried this and as soon as a connection is made about a minute later I'm disconnected again. Any ideas as how to resolve this problem? Also I was told that if I have DSL that this wouldn't be a problem
View 9 Replies View RelatedI am in the process of opening an internet cafe. I dont know exactly what a pc server does on the network... or do I really need one? Is the switch/hub sufficent to connect all pcs to the moderm to connect to the internet?
View 1 Replies View RelatedI moved to a remote area where I cannot get DSL or Broadband. I can however get Dial up, like earthlink and Netzero. Before I signup for one of these services, I would like to know if there is any way to make my dialup a wireless conection for my laptops. I like to move around using the computer, I hate being at a desk having to sit there and not be able to move where I want.I have a modem that I used for my old dsl connection. Will this work?
View 1 Replies View RelatedThe PPPoE connection can be successfully established only if the PC dials up, but not if the router replaces the PC to do so.Both the PC and the router are identically configured for this purpose, i.e. using the same ADSL dial-up account(usr/passwd pair). As a whole, we can exclude any wrong configuration on the router itself.
View 3 Replies View RelatedMy computer is Dell Inspiron530 w/32bit vista & 2.00gb. Is this ok for DSL?
View 3 Replies View RelatedI have a ventilation controller that connects using a phone line. I have do not have a second phone line to dial out with my computer. is there a way i could set up dialing via broadband?
View 2 Replies View Relatedi have one xp machine. i wnd to configure two different dial up connection in one xp machine for band width sharing.
View 1 Replies View RelatedI believe that the Cisco Unified Communications Manager Express matches the outbound VoIP dial peer digit-by-digit, because:
1. when using the debug command it shows how it works digit-by-digit till it match a pattern
2. It says in the study guide ( If a match is found, the router immediately processes the call - chapter 6) so I understand its not en bloc
How i can create dial up connection i don't know to create?
View 1 Replies View RelatedI have a dlink DWA130 wireless N adapter connected and working. But AOL Dialup takes over. When disconnecting the phone line for AOL, there is no internet connection. The adapter is connected and has great signal strength. What can I do to make the wireless adapter work independently from AOL dialup?
View 3 Replies View RelatedI had a Sony Viao with Windows Vista for some years and I managed to create a bridge using the Sony Viao laptop and my o2 usb modem. That was some time ago and now I have a new laptop with Windows 7 ?I have to mention that I do not have wireless connections. I have an o2 modem and an ethernet cable. They are the only two connections that show up in my internet connections. The LAN connection has an image of a ethernet cable connection while the o2 connection has an image of a phone.whenever I watch youtube walk throughs it never looks like my set up. Ive tried everything over and over. Turning off UAC, turning on sharing but nothing has worked yet. When I just select the LAN connection and right click there is an option to Bridge. When I right click the o2 connection its not there. When I select both the option isnt there either.
View 2 Replies View RelatedI am without my connection until repairs are made inthe following week. I am trying to set up netzero with my current equipment, but cannot find the cd for my netgear router WNR1000.
View 1 Replies View RelatedBasically i need to test to see where the telephone lines are terminated, because when they where built into the walls the used standard cat5e cable to terminate it to an RJ-11 jack but over in the wiring panel it (i assume it is anyways) terminates to an RJ-45 jack but im not sure if this is really the cable for the telephone or something else, so i have a phone connected to the wall jack and a computer on this end and i would like to send a dial tone or any tone in general that the phone can pickup.
View 3 Replies View Related