Cisco VPN :: 877 ADSL Router Which Won't Allow To Play With VPNs
May 20, 2011
I have a Cisco 877 ADSL router which won't let me play with my VPNs like I used to in pre-Cisco days.I have a VPN server which resides on the inside of the network which used to get it's L2TP as well as PPTP tunnels passed straight through the ADSL router. No problems there with the old router.Now I opened the relevant ports for both TCP and UDP on the 877, but VPN simply won't establish when trying to connect from the outside. Process of getting the 877 to stop wanting to take charge of things VPN and just pass them off to an inside server?
I need to VPN into my work from my laptop on the private side of the 877. This works fine until after authentication, then the VPN connection goes silent, no traffic going through. Works fine when for instance using my iphone hotspot to connect through from my laptop. It's only not working when the 877 is in the equation.
View 0 Replies
ADVERTISEMENT
Aug 24, 2012
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies
View Related
Nov 19, 2011
Videos on other sites work fine but Youtube videos won't play when im using either of my routers. They also work fine connected straight to the modem, i've reset, factory defaults, uninstalled and re-installed Firefox. I've tried other browsers.
View 10 Replies
View Related
Jun 4, 2012
My roommates and I like to play diablo 3 and wow at the same time, but we experience frequent disconnects. If one of the machines is in the DMZ on the router it doesn't disconnect when the other two do. I've turned the router firewall off and this does nothing to work. Can I just forward all the appropriate ports to ALL of the computers?
Router model: FR-300RTR(rebranded d-link)
Router firmware: DD-WRT c24-sp2
Router firewall: off
UPnP: on
dmz: off
manual port forwarding: off
All machines are running windows 7
View 1 Replies
View Related
Sep 6, 2012
I have been trying to connect to an online radio station, a shoutcast. I am unable to do this when connected to my EA3500. I do not think it is a port issue since I can connect to a different station using the same port. I can listen to many other shoutcast streams with no problems.
A friend with an older Linksys router is able to connect to the station with no problems.
I have turned off the ipv4 firewall, ipv6 firewall. I've tried DMZ, port triggering, forwarding. Still the stream will not play. I use the Winamp player, Windows Media player, Real player. All the other shoutcast streams I have tried work, but not the one I need to work.
If I bypass the router it works fine on any of my 4 pc desktops, 4 laptops. My iphone using the winamp app can not get the stream if using the wirless, but can if I turn off wirless and use 3G.
I am writing a radio series for this station and it starts airing the show in a couple of weeks, I really want to be able to hear it without eating up my data on my phone.
View 9 Replies
View Related
Feb 13, 2013
I have a Cisco DPC3825 and i don't know how to port forward it i want to port forward so i can host my server without hamachi?
View 1 Replies
View Related
Jan 22, 2011
i have a DIR-601. Basic settings, port forwarded for Xbox live and Wolfenstein enemy territory.I have a home PC with a wired connection and a laptop which is set up through wireless. I installed the game Wolfenstein: Enemy Territory on my laptop and every time I start the game and attempt to fetch a server list, my router resets itself. The game works fine when I connect directly to my modem, but not when I connect to my router
View 1 Replies
View Related
Feb 3, 2012
I have just bought one of these linksys routers to try and solve a problem I am having with disconnects when playing online games with a ps3 and also some moderate firewall states with some games. My isp is bt and I have a black home hub v2, the problem with this router is that it does not like doing dmz or port forwarding for that matter very successfuly, apparently the new router I have bought is much better at these things.So I'm trying to figure out if its best for me to buy a modem to go with this router or to configure the hh to work as a modem only. Also if I get a new modem will this cause any problems with using the bt vision services.
View 2 Replies
View Related
Sep 29, 2011
I have a pretty basic NETGEAR router right now. I have a Zyxel modem that Centurylink sent when I signed up for my DSL service. The Zyxel modem connects to my NETGEAR router. When I play online either wireless or wired from the Netgear modem I have major connection issue.However, if I disconnect from the netgear modem and connect from the Zyxel directly to the ps3 I have zero problems.
View 19 Replies
View Related
Jul 23, 2011
I'm experiencing dropping connection and can't play online games because of extreme lag. when pinging certain sites here is the results at the bottom. so very extremely high ping. then after a while like 5 mins, when i hover my mouse cursor at the network icon it says limited access and i don't have any internet connection, even powercycling doesn't work. it stays like that. when using direct connection to the modem only it works fine. but when using the wrt120n router i experience that problem either wired or wireless it stays the same. My firmware is latest, router settings default.
View 5 Replies
View Related
Mar 9, 2012
I have a Linksys E4200v2 couple days ago. After set up everything seem be working fine, accept my iPhone 4s. I can do almost things on my iPhone, but when I tried streaming video or streaming music from apps on the phone it stared buffering.... play..... and.... stop.... almost every 30s which never happen with my old Linksys E1000. And It happen with my wife's phone too. Even my internet speed is not bad at all (Ping: 24 / Download 23Mbs / Upload 4Mbs). So I can guess that problem from the router. Then I swap the E4200v2 with the E1000, everything works fine (it just a litle bit slower when loading at begin).
View 1 Replies
View Related
Dec 11, 2012
I have a E1200 Router and my ISP is Comcast. How to have the best settings to play online. I did the Static IP set up. But I am still having laggy off and on connection. I called Comcast to see what can i do. They said its problems with the router. I enter the right numbers for PS3 in the Single Port Forwarding and Port Range Forwarding. I turn on DMZ and entered the same IP Address as it is on my PS3 I dont have a problem with Resetting the whole Router and starting from scratch ?
View 9 Replies
View Related
Nov 15, 2012
wrt54g will not play videos. I have connected my modem directly to computer and it works fine if I connect thru the router it will not play.
View 2 Replies
View Related
Sep 20, 2012
The E4200v1 does not play nice with the 4s on iOS6!!It will not work at all with Wireless N mode or mixed mode settings. If I have it on these settings, the iPhone will connect (slowly) to the router, but access content on the browser takes forever (or not at all).I have to set the router to G only nmode, but obviously this is no good for the rest of my devices!
View 3 Replies
View Related
Jan 15, 2012
Why I can't play online on xbox live. I'm set on going online but when I go on to play online for MW3(Modern Warfare 3) my NAT Type says strict,I can't join any of my friends games. It says to go on infintyward.com/Nat and when I do it doesn't show my model of linksys (WRT300N) i reset my xbox,my router and still nothing
View 3 Replies
View Related
Mar 12, 2012
I have a Sony Vita , PS3, & Cisco ASA 5505 firewall. I can get remote play to work only if the PS3 is powered on. The ASA will kill any Wake-on LAN packet no matter what I do to try to allow it. Apparently it doesn't support directed broadcast.
View 1 Replies
View Related
Jul 9, 2012
i recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies
View Related
Aug 30, 2012
I recently purchased the Belkin PLAY N600 router to create a private network for my home theatre setup.I have a primary home network 192.168.0.x (NetGear) which I use for all my computing needs. I extended a network cable to my Home theatre area and plugged in the N600 router. After this, I attached a USB external hard drive to the router and it works great. I can see it from the 192.168.2.x home theatre network (Belkin).I would like to expose the USB hard drive hooked to the Belkin Router to my primary network so that I can copy over my music and pictures without having to physically move the hard driveonto a PC connected to the primary domain.The Belkin router has a DMZ function which exposes an IP on its internal (192.168.2.x)network to the external (192.168.0.103) network.Is it feasible to expose the USB drive to my primary home network?
View 1 Replies
View Related
Feb 1, 2011
I have been able to play streaming video via Windows Media Player with no problems for just about forever until last month.No software has changed. i have the latest firmware (2.39.2e) for the router. i am able to play the same videos when i use my AT&T data connection or when i am connected at work, ,so i know it's not the files i'm trying to view. WMP fails to play whether i am hard connected or wirelessly connected.
View 1 Replies
View Related
Feb 6, 2013
I have recently discovered that I can stream audio from my WRT54G V2 via a wireless extender.I can not play internet radio, or stram Rhapsody via the extender.The extender will not stream audio.This is actually quite normal behavior of a Range Extender. Range Extenders work off of the idea of pulling a signal from the Base Station and then repeating the signal frequently, this generally causes rebuffering issues with most wireless devices within a network.I believe I need a wireless extender that does not repeat the signal, more of a wireless access point.
View 2 Replies
View Related
Apr 21, 2011
I'm trying to network a small office and have the following devices:
SMCD3G Cable Modem
Belkin Play N600 Router
Digi Mil-H1130 8 Port Ethernet SOHO Hub
Hubbel Cat5 Patch Panel (goes up to 12)
We're replacing our DSL line with a Cable line. Our DSL was a one piece wireless router/modem. When it was installed, it was inside our office, next to the server, and plugged into Wall Jack 1 for all the other computers to connect to. Our server plugged into this modem/router. We didn't have the Belkin Router at the time. The Patch Panel wires went into the Hub behind our office and everything was fine.
The cable modem is now next to the Hub and Patch Panel. I bought the router since we didn't have the wireless feature that the DSL had and everyone I spoke to said I need a router to set up the office. I ran one of the LAN lines from the modem into the Router where it says Modem (WAN). From the Router, I ran the line 1 (LAN) into the Hub. (Does the number matter if nothing is plugged into it in our office?) No computer is able to connect to the internet except my laptop which connects wireless. It works fine.
Another problem. We have a server computer that's Unix based. In order for anyone to connect to the server to access the office software used, the IP address of the router must be 192.9.2.1 or the computer your using won't connect via Multiview 2000 Terminal Emulator. I can't connect to the server because the IP address of the router is still 192.168.2.1. I don't know where I have to go in the router settings to change it. I've tried a few spots and it tells me the IP address is invalid. The settings I had with the DSL modem/router were:
Modem IP address - 192.9.2.1
Subnet Mask - 255.255.255.0
DHCP Start Address - 192.9.2.100
DHCP End Address - 192.9.2.150
It's not like I need to run wires. Everything is set. If something is plugged into a wrong spot, I can switch it.
Additional info:
There are 4 computers in the office and 8 numbered wall jacks.
Server computer - Wall jack 8 (IP address of this machine - 192.9.2.25)
XP Machine 1 - Wall jack 4 (can't connect to server! No internet.)
XP Machine 2 - Wall jack 1 (Is able to connect to the server! No internet.)
Win CE Machine - Wall jack 9 -
I assume. I have a wire that goes through the wall on this machine and it isn't marked. (Rarely used so not sure about server connection)
Wireless Windows7 laptop - connects to the internet fine since it bypasses all these wires. Can't connect to server.
Under the DHCP client list, only 2 computers are listed. The one that has internet is my computer. The other computer listed is wall jack 4 and that has internet now.
my computer - 192.9.2.2
wall jack 4 - 192.9.2.3
The router IP is 192.168.2.1 and the Cable Modem is 10.1.10.11. If I type either number into my web browser it will take me to the router setup page. I don't know where/how to check if it's only one device acting as DHCP. What I want to do is be able to get online with all the computers as well as have access to the software on the server through the office wall jacks. In order to do that I need the router IP address to be 192.9.2.1 and then I'd be able to connect to it.
Right now, one computer is able to connect to the server via hard wire but can't connect to the internet.Another computer is able to connect to the internet via hard wire but can't connect to the server.My laptop can connect wireless to the internet but not the server. In a perferct world, all the computers should be able to connect to both the internet and the server. Right now, it's one or the other with both hard wired machines and I don't know why. Is there a wire not in the hub right? Is a patch panel wire plugged into the wrong port of the hub? I don't know what's supposed to go where. tell me "wire X from the modem goes to Port Z of the router, and Wire Y from the the router goes to number V on the Hub, and that wire goes to number T on the patch panel for the Port number R in the office to work..." I'll try it.
Then I think all I need to do is change the router's IP address to 192.9.2.1 and everyone should be able to connect to the server through the Multiview 2000 Terminal Emulator.When I tried to change the IP address on the router it's telling me it's not valid. Under LAN settings it says 192.168.2.1 - when I try to change it to 192.9.2.1 it tells me LAN IP address is invalid. I clicked on More Info below that in the router page and a pop up gives me info. It says:
The "IP address" is the Internal IP address of the Router. To access the advanced setupinterface, type this IP address into the address bar of your browser. This address can be changed if needed. To Change the IP address, type in the new IP address and click "ApplyChanges". The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:
192.168.y.x (where y is anything between 0 and 255, and x is anything between 1 and 254.)
10.y.y.x (where y is anything between 0 and 255, and x is anything between 1 and 254.)
172.z.y.x (where z is anything from 16 to 31, and y is anything between 0 and 255, and x is anything between 1 and 254.)
View 4 Replies
View Related
Feb 1, 2013
I am putting an pre-labbed DMVPN Hub config onto a production 1841. We had to upgrade the IOS to support protection with NAT so the current IOS we're running is c1841-adventerprisek9-mz.124-25g.bin.I can paste the configuration in fine (via the tunnel interfaces) and the router accepts it however the 'show dmvpn', 'debug dmvpn' and other related commands don't work. I have checked the IOS feature navigator and it definitely shows that DMVPN phase 1 and 2 are supported in this image.
View 5 Replies
View Related
Feb 1, 2012
Actually I have to make a VPN between an 5520 ASA and a Cisco 887VA-K9 Router. Connected to ASA I have the outside interface, the inside-DMZ interface, the PCs interface and the VoIP interface. In the other site I will need to have a new subnet and a VoIP phone which I need to connect to the VoIP subnet in the other side in order to work with our CCM servers.I need two VPN established between ASA and 887 Router?
View 15 Replies
View Related
Oct 24, 2011
I have a pair of 5505s with an IPsec VPN between them. On the first 5505, I also have a user connecting to it via client based vpn. The user cannot access systems on the other side of the ipsec tunnel. That 5505 protects subnet a.b.c.d, the user is on subnet a.b.e.d which is not inclusive to a.b.c.d. First, am I correct in the assumption that I need to add the vpn network of a.b.e.d to the list of protected networks, and second if I change the list, does it drop and reset the ipsec vpn?
View 2 Replies
View Related
Aug 16, 2011
How much the CPU is impacted by SSL VPNs on Cisco ASA 5500's?I believe that the ASA offloads a lot of its encryption/decryption on a built in VPN accelerator rather than placing load on the main CPU. Is this correct?
According to the ASA 5520 specs - it can handle a throughput of up to 225Mbps of VPN traffic. Of course, it does not say whether this is SSL or IPSEC but I would like to understand what impact say 100Mbps of SSL VPN traffic would have on the main CPU.
We need this information to gauge whether an existing firewall has enough capacity to cope with existing load plus additional new SSL VPNs.
View 1 Replies
View Related
Mar 24, 2013
I've got a setup where we have a wireless connection coming in and using mikrotik router. We have multiple stores coming in via the wireless with a dmvpn.
The vpn's terminate on the cisco c870 and can be seen when running: show dmvpn.The cisco has a default route to the fibre router (10.0.0.252). The wireless router is the default gateway for the network. The failover from wireless to adsl fails. (due to the cisco routing traffic back to the wireless router when wireless fails)
If I change the default route on the cisco to dialer1, the failover works, but none of the vpn's connect. The Branches all have dynamic ip addresses. The HO has a static ip.
My goal: I want to achieve adsl failover for when the wireless goes down and still have the vpn's connected.
Can I have some sort of "Dynamic" route on the cisco. So when the vpn traffic comes in via wireless and hits the cisco, the vpn traffic can then go back out that way via the wireless router, but still have a default gateway on the dialer interface for failover?
View 1 Replies
View Related
Feb 22, 2012
I have been endlessly searching around online, and trying things on the firewall, and cant seem to find an answer to this problem. Its probably something really simple right under my nose! I am using an ASA 5510, which currently has a few seperate site-to-site VPN connections configured, which connect to other Cisco devices on clients networks.
I work from home, so also connect to our network using Remote Access VPN (any connect) to connect to the network at the data centre.
Just to be clear, here is my amazingly drawn network diagram:
[[my house]]-------------- <any connect VPN>------------[[ASA 5510 / Data centre]]-----------<site-to-site>-----------------[[Client network]]
The problem I am having, is that I cannot connect directly from my house to the client network, I need to RDP into some server in the data center, then from there I can see the Clients network. Is there routing to be setup somewhere? between VPN's? Ive looked into the routing options on the firewall and cant seem to find anything that works. I've searched for this and cant find answers, even some sources saying its impossible.
View 7 Replies
View Related
Feb 20, 2013
how many VPNS are configure in this device
the o/p:
sh vpn-sessiondb
Active Session Summary
Sessions:
Active : Cumulative : Peak Concurrent : Inactive
SSL VPN : 0 : 0 : 0
Clientless only : 0 : 0 : 0
With client : 0 : 0 : 0 : 0
Email Proxy : 0 : 0 : 0
[code]...
View 1 Replies
View Related
Jul 2, 2012
We have a corporate site with a Cisco ASA 5580 (8.1), a remote office with a Cisco ASA 5510 (8.2) with a L2L VPN to corporate. A vendor has a L2L VPN to the corporate ASA with access to the remote office across the VPNs (hairpinning). The corporate office accesses an application at the vendor on port 23. Everything is working with regards to the vendor accessing resources to the remote office and the corporate office accessing the application at the vendor. Our goal now is to restrict the vendor to port 23 from the corporate network and port 9100 to the remote office. On the corporate ASA I setup a VPN filter and applied to the vendor's L2L vpn but when I apply the filter (see below) all traffic stops to the vendor such as telnet.
View 6 Replies
View Related
Nov 28, 2011
I have both a Easy VPN server and a site-to-site VPN on the same outside interface of a 2911 router.
Currently, a Easy VPN client has no route int the router then out the site-to-site VPN to the remote site.
How can I create this route?
[code]...
View 1 Replies
View Related
Jun 6, 2011
So I have a server running Linux and am looking to add VPN functionality to my home network. I have OpenSSH running and it works great for tunneling and remote file transfers but doesn't quite get the job done.I would like to be able to map a network drive in Windows to my Linux box and understand a VPN could accomplish this, problem is I really don't know anything about Virtual Private Networking! I was hoping someone could explain to me the differences between SSH / VPNs and point me in the right direction towards configuring OpenVPN on my Linux box.
View 4 Replies
View Related
Mar 21, 2011
I've been reading this site for a while, and finally decided to post I'm really interested to see what everyones opinion on this is.My company currently uses what i would call traditional site to site VPN's using crypto maps, main site has a pair of ASA's in HA and remote sites use ISR's like 1801's.I've recently been playing in my lab with GRE tunnels using IPSec protection (note this is config from my labs, so ip's and key's are just randomly selected)
View 17 Replies
View Related
Jun 15, 2011
what is the maximum number of Lan-to-Lan and user vpns supported in the ISR G2 2911 and 2921?
View 5 Replies
View Related
