FR-300RTR / How To Play Diablo 3 And WoW Behind DD-WRT Router
Jun 4, 2012
My roommates and I like to play diablo 3 and wow at the same time, but we experience frequent disconnects. If one of the machines is in the DMZ on the router it doesn't disconnect when the other two do. I've turned the router firewall off and this does nothing to work. Can I just forward all the appropriate ports to ALL of the computers?
Router model: FR-300RTR(rebranded d-link)
Router firmware: DD-WRT c24-sp2
Router firewall: off
UPnP: on
dmz: off
manual port forwarding: off
All machines are running windows 7
View 1 Replies
ADVERTISEMENT
May 21, 2012
While playing on Diablo 3 using DIR-615, it will always get disconnected from server after 2 to 20 minutes. The router firmware version is 7.12.
View 4 Replies
View Related
Nov 19, 2011
Videos on other sites work fine but Youtube videos won't play when im using either of my routers. They also work fine connected straight to the modem, i've reset, factory defaults, uninstalled and re-installed Firefox. I've tried other browsers.
View 10 Replies
View Related
May 20, 2011
I have a Cisco 877 ADSL router which won't let me play with my VPNs like I used to in pre-Cisco days.I have a VPN server which resides on the inside of the network which used to get it's L2TP as well as PPTP tunnels passed straight through the ADSL router. No problems there with the old router.Now I opened the relevant ports for both TCP and UDP on the 877, but VPN simply won't establish when trying to connect from the outside. Process of getting the 877 to stop wanting to take charge of things VPN and just pass them off to an inside server?
I need to VPN into my work from my laptop on the private side of the 877. This works fine until after authentication, then the VPN connection goes silent, no traffic going through. Works fine when for instance using my iphone hotspot to connect through from my laptop. It's only not working when the 877 is in the equation.
View 0 Replies
View Related
Sep 6, 2012
I have been trying to connect to an online radio station, a shoutcast. I am unable to do this when connected to my EA3500. I do not think it is a port issue since I can connect to a different station using the same port. I can listen to many other shoutcast streams with no problems.
A friend with an older Linksys router is able to connect to the station with no problems.
I have turned off the ipv4 firewall, ipv6 firewall. I've tried DMZ, port triggering, forwarding. Still the stream will not play. I use the Winamp player, Windows Media player, Real player. All the other shoutcast streams I have tried work, but not the one I need to work.
If I bypass the router it works fine on any of my 4 pc desktops, 4 laptops. My iphone using the winamp app can not get the stream if using the wirless, but can if I turn off wirless and use 3G.
I am writing a radio series for this station and it starts airing the show in a couple of weeks, I really want to be able to hear it without eating up my data on my phone.
View 9 Replies
View Related
Jan 22, 2011
i have a DIR-601. Basic settings, port forwarded for Xbox live and Wolfenstein enemy territory.I have a home PC with a wired connection and a laptop which is set up through wireless. I installed the game Wolfenstein: Enemy Territory on my laptop and every time I start the game and attempt to fetch a server list, my router resets itself. The game works fine when I connect directly to my modem, but not when I connect to my router
View 1 Replies
View Related
Feb 3, 2012
I have just bought one of these linksys routers to try and solve a problem I am having with disconnects when playing online games with a ps3 and also some moderate firewall states with some games. My isp is bt and I have a black home hub v2, the problem with this router is that it does not like doing dmz or port forwarding for that matter very successfuly, apparently the new router I have bought is much better at these things.So I'm trying to figure out if its best for me to buy a modem to go with this router or to configure the hh to work as a modem only. Also if I get a new modem will this cause any problems with using the bt vision services.
View 2 Replies
View Related
Sep 29, 2011
I have a pretty basic NETGEAR router right now. I have a Zyxel modem that Centurylink sent when I signed up for my DSL service. The Zyxel modem connects to my NETGEAR router. When I play online either wireless or wired from the Netgear modem I have major connection issue.However, if I disconnect from the netgear modem and connect from the Zyxel directly to the ps3 I have zero problems.
View 19 Replies
View Related
Feb 13, 2013
I have a Cisco DPC3825 and i don't know how to port forward it i want to port forward so i can host my server without hamachi?
View 1 Replies
View Related
Jul 23, 2011
I'm experiencing dropping connection and can't play online games because of extreme lag. when pinging certain sites here is the results at the bottom. so very extremely high ping. then after a while like 5 mins, when i hover my mouse cursor at the network icon it says limited access and i don't have any internet connection, even powercycling doesn't work. it stays like that. when using direct connection to the modem only it works fine. but when using the wrt120n router i experience that problem either wired or wireless it stays the same. My firmware is latest, router settings default.
View 5 Replies
View Related
Mar 9, 2012
I have a Linksys E4200v2 couple days ago. After set up everything seem be working fine, accept my iPhone 4s. I can do almost things on my iPhone, but when I tried streaming video or streaming music from apps on the phone it stared buffering.... play..... and.... stop.... almost every 30s which never happen with my old Linksys E1000. And It happen with my wife's phone too. Even my internet speed is not bad at all (Ping: 24 / Download 23Mbs / Upload 4Mbs). So I can guess that problem from the router. Then I swap the E4200v2 with the E1000, everything works fine (it just a litle bit slower when loading at begin).
View 1 Replies
View Related
Dec 11, 2012
I have a E1200 Router and my ISP is Comcast. How to have the best settings to play online. I did the Static IP set up. But I am still having laggy off and on connection. I called Comcast to see what can i do. They said its problems with the router. I enter the right numbers for PS3 in the Single Port Forwarding and Port Range Forwarding. I turn on DMZ and entered the same IP Address as it is on my PS3 I dont have a problem with Resetting the whole Router and starting from scratch ?
View 9 Replies
View Related
Nov 15, 2012
wrt54g will not play videos. I have connected my modem directly to computer and it works fine if I connect thru the router it will not play.
View 2 Replies
View Related
Sep 20, 2012
The E4200v1 does not play nice with the 4s on iOS6!!It will not work at all with Wireless N mode or mixed mode settings. If I have it on these settings, the iPhone will connect (slowly) to the router, but access content on the browser takes forever (or not at all).I have to set the router to G only nmode, but obviously this is no good for the rest of my devices!
View 3 Replies
View Related
Jan 15, 2012
Why I can't play online on xbox live. I'm set on going online but when I go on to play online for MW3(Modern Warfare 3) my NAT Type says strict,I can't join any of my friends games. It says to go on infintyward.com/Nat and when I do it doesn't show my model of linksys (WRT300N) i reset my xbox,my router and still nothing
View 3 Replies
View Related
Mar 12, 2012
I have a Sony Vita , PS3, & Cisco ASA 5505 firewall. I can get remote play to work only if the PS3 is powered on. The ASA will kill any Wake-on LAN packet no matter what I do to try to allow it. Apparently it doesn't support directed broadcast.
View 1 Replies
View Related
Jul 9, 2012
i recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies
View Related
Aug 30, 2012
I recently purchased the Belkin PLAY N600 router to create a private network for my home theatre setup.I have a primary home network 192.168.0.x (NetGear) which I use for all my computing needs. I extended a network cable to my Home theatre area and plugged in the N600 router. After this, I attached a USB external hard drive to the router and it works great. I can see it from the 192.168.2.x home theatre network (Belkin).I would like to expose the USB hard drive hooked to the Belkin Router to my primary network so that I can copy over my music and pictures without having to physically move the hard driveonto a PC connected to the primary domain.The Belkin router has a DMZ function which exposes an IP on its internal (192.168.2.x)network to the external (192.168.0.103) network.Is it feasible to expose the USB drive to my primary home network?
View 1 Replies
View Related
Feb 1, 2011
I have been able to play streaming video via Windows Media Player with no problems for just about forever until last month.No software has changed. i have the latest firmware (2.39.2e) for the router. i am able to play the same videos when i use my AT&T data connection or when i am connected at work, ,so i know it's not the files i'm trying to view. WMP fails to play whether i am hard connected or wirelessly connected.
View 1 Replies
View Related
Feb 6, 2013
I have recently discovered that I can stream audio from my WRT54G V2 via a wireless extender.I can not play internet radio, or stram Rhapsody via the extender.The extender will not stream audio.This is actually quite normal behavior of a Range Extender. Range Extenders work off of the idea of pulling a signal from the Base Station and then repeating the signal frequently, this generally causes rebuffering issues with most wireless devices within a network.I believe I need a wireless extender that does not repeat the signal, more of a wireless access point.
View 2 Replies
View Related
Apr 21, 2011
I'm trying to network a small office and have the following devices:
SMCD3G Cable Modem
Belkin Play N600 Router
Digi Mil-H1130 8 Port Ethernet SOHO Hub
Hubbel Cat5 Patch Panel (goes up to 12)
We're replacing our DSL line with a Cable line. Our DSL was a one piece wireless router/modem. When it was installed, it was inside our office, next to the server, and plugged into Wall Jack 1 for all the other computers to connect to. Our server plugged into this modem/router. We didn't have the Belkin Router at the time. The Patch Panel wires went into the Hub behind our office and everything was fine.
The cable modem is now next to the Hub and Patch Panel. I bought the router since we didn't have the wireless feature that the DSL had and everyone I spoke to said I need a router to set up the office. I ran one of the LAN lines from the modem into the Router where it says Modem (WAN). From the Router, I ran the line 1 (LAN) into the Hub. (Does the number matter if nothing is plugged into it in our office?) No computer is able to connect to the internet except my laptop which connects wireless. It works fine.
Another problem. We have a server computer that's Unix based. In order for anyone to connect to the server to access the office software used, the IP address of the router must be 192.9.2.1 or the computer your using won't connect via Multiview 2000 Terminal Emulator. I can't connect to the server because the IP address of the router is still 192.168.2.1. I don't know where I have to go in the router settings to change it. I've tried a few spots and it tells me the IP address is invalid. The settings I had with the DSL modem/router were:
Modem IP address - 192.9.2.1
Subnet Mask - 255.255.255.0
DHCP Start Address - 192.9.2.100
DHCP End Address - 192.9.2.150
It's not like I need to run wires. Everything is set. If something is plugged into a wrong spot, I can switch it.
Additional info:
There are 4 computers in the office and 8 numbered wall jacks.
Server computer - Wall jack 8 (IP address of this machine - 192.9.2.25)
XP Machine 1 - Wall jack 4 (can't connect to server! No internet.)
XP Machine 2 - Wall jack 1 (Is able to connect to the server! No internet.)
Win CE Machine - Wall jack 9 -
I assume. I have a wire that goes through the wall on this machine and it isn't marked. (Rarely used so not sure about server connection)
Wireless Windows7 laptop - connects to the internet fine since it bypasses all these wires. Can't connect to server.
Under the DHCP client list, only 2 computers are listed. The one that has internet is my computer. The other computer listed is wall jack 4 and that has internet now.
my computer - 192.9.2.2
wall jack 4 - 192.9.2.3
The router IP is 192.168.2.1 and the Cable Modem is 10.1.10.11. If I type either number into my web browser it will take me to the router setup page. I don't know where/how to check if it's only one device acting as DHCP. What I want to do is be able to get online with all the computers as well as have access to the software on the server through the office wall jacks. In order to do that I need the router IP address to be 192.9.2.1 and then I'd be able to connect to it.
Right now, one computer is able to connect to the server via hard wire but can't connect to the internet.Another computer is able to connect to the internet via hard wire but can't connect to the server.My laptop can connect wireless to the internet but not the server. In a perferct world, all the computers should be able to connect to both the internet and the server. Right now, it's one or the other with both hard wired machines and I don't know why. Is there a wire not in the hub right? Is a patch panel wire plugged into the wrong port of the hub? I don't know what's supposed to go where. tell me "wire X from the modem goes to Port Z of the router, and Wire Y from the the router goes to number V on the Hub, and that wire goes to number T on the patch panel for the Port number R in the office to work..." I'll try it.
Then I think all I need to do is change the router's IP address to 192.9.2.1 and everyone should be able to connect to the server through the Multiview 2000 Terminal Emulator.When I tried to change the IP address on the router it's telling me it's not valid. Under LAN settings it says 192.168.2.1 - when I try to change it to 192.9.2.1 it tells me LAN IP address is invalid. I clicked on More Info below that in the router page and a pop up gives me info. It says:
The "IP address" is the Internal IP address of the Router. To access the advanced setupinterface, type this IP address into the address bar of your browser. This address can be changed if needed. To Change the IP address, type in the new IP address and click "ApplyChanges". The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:
192.168.y.x (where y is anything between 0 and 255, and x is anything between 1 and 254.)
10.y.y.x (where y is anything between 0 and 255, and x is anything between 1 and 254.)
172.z.y.x (where z is anything from 16 to 31, and y is anything between 0 and 255, and x is anything between 1 and 254.)
View 4 Replies
View Related
Sep 29, 2011
I restored the computer to factory defaults to have a fresh start. I downloaded some games and this is when I realized my problem. The first instance of the problem was when I was playing a game called "League of Legends". About ten minutes through the game, the game would freeze. It isn't a computer freeze because I could still move the mouse and see people walking in place. I was then disconnected. The second instance was when I was playing a game called "Dragon Nest". I would run through a dungeon and after a short-while everything would start to move in placeI could still move freely but whenever I tried to hit something the hits wouldn't register. After about 30 seconds everything went back to normal and a lot of monsters died and I was hurt. I tested my computers download and upload speed to see if anything was different from my family desktop. My download speed on the laptop is 5 mbps, and the one on the desktop is 26 mbps. The desktop is directly hooked up to the modem, and the laptop is wireless (I don't know if this would be the reason for the difference in speed, and or disconnection/lag issues.) I have also noticed that videos on YouTube load A LOT slower than on my desktop. I finally gave up and tried to use my desktop but I seem to have disconnected from Dragon Nest on there as well (except this time it automatically disconnected me, it didn't have a pause in the game.
View 1 Replies
View Related
Jul 27, 2011
I am very upset because my ping is too high and i cant play counterstrike online.
View 2 Replies
View Related
Jan 23, 2012
When i go to steam and Select Killing Floor, it gets stuck at the Querrying master server list ...Same with Crime Craft, Stuck at loading Screen..Same with San Andreas Multiplayer, Internet and Hosted tabs not showing any servers..So i guess my modem has some strange setting enabled that doesnt allow to connect to any master servers or something
View 1 Replies
View Related
Jan 26, 2012
When I play games that are downloaded to my PC from Aeria games I run into intermittent latency. It happens every 6 minutes and last for about 4 minutes so for every ten minutes I get to play about 6 minutes. It only happens with Aeria games; all of them.Is this an issue with my connection to the server or is it possible that it is due to security software?
View 13 Replies
View Related
Dec 28, 2012
the dvd player says its connected to the internet when I go through the wireless settings but it still says there is a connectivity issue. It was previously showing 0.0.0.0 for all IP address information etc. I read the last post on this forum considering the issue and guessed at what I should input in under manual. The data etaf requested from the other guy is shown below.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Andrew-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 1 Replies
View Related
May 24, 2011
At my university I have huge lag spikes when playing Hon (heroes of newerth) my friends are playing and have no issues. As of now, I have turned all the graphics down to the lowest settings, disabled every function of the windows firewall I could find, and ensured no other programs are running (even closed explorer) Any idea what could be causing this? (I have no antivirus active)
View 4 Replies
View Related
Mar 24, 2013
HD (1920x1080) TV sees and plays all SD mpg (720x576) stored on a Lacie network drive. Now working in HD (1920x1080) and find that the TV does not even see the mpg files, let alone play them. If I convert the HD files to SD they are then visible again. It seems odd that a HD TV cannot see and play HD videos.
View 2 Replies
View Related
Jul 11, 2011
Lenovo core2duo Desktop XP Pro works OK to internet when hard wired to router.Marvell 88E8057 network card with latest May 2011 drivers on XP. Both a gateway laptop and an HP laptop also work hardwired.When I use a Wireless Access point, it works fine with the laptops. However, when I use the Lenovo desktop connected directly by wire to the WAP, I only get "partial" internet access.I can ping yahoo, I can get a google page. But any "thick" content seems to be blocked.I can't play any youtube videos on the Lenovo via the WAP, or view websites with rich content.I get the youtube page, but it hangs on play. the laptops work wether wired to the router, or wired to the WAP. With any content including youtube.
View 6 Replies
View Related
May 26, 2011
I have been trying to play WoW but it seems it is blocked by my netgear firewall. Thus, I tried using a proxy server [URL] but it seems that only allows me to surf the web but not open up the actual game client. So, now im not sure what i need to do to bypass the block.
View 1 Replies
View Related
Dec 17, 2011
In Age of Empires ESO will let me log in to game, but fail to join games in lobby
View 1 Replies
View Related
Mar 23, 2012
Trying to get this computer online but nothing is working. Windows Updates will download and install updates. The network center says it has access and is connected to the internet with zero problems. However, whenever I try to browse the internet or play a game online it will not connect.I've tried reinstalling my nic drivers. I've rebooted the router and modem numerous times.I've tried ipconfig /release and /renewI've tried netsh ip resetI've turned off the firewall and uninstalled any old antivirus software.All my settings are set to automatic.There are 2 other computers, 2 wii's 2 xboxs on this network and they all run flawlessly.
View 1 Replies
View Related
Nov 2, 2011
I am having a lot of trouble with my internet, and have been for the past 2 days. I cannot play any games or even use the internet to browse 99% of the time.The only time I can get it to work for about 5 minutes is like so; I open internet explorer and after a few minutes of loading it tells me that it cannot connect to the web page (or something like that). It has a troubleshoot option, after clicking it, it scans for possible solutions but it never finds anything. When it tells me it found nothing, there is another button to explore additional options, the instant I click this button, everything starts working again for a few minutes, and it just doesn't make sense to me why this is happening.I have to study and I need the internet, and I would like to play games again.
View 1 Replies
View Related
