Cisco WAN :: Cannot Find ADSL Firmware 4.0.0.18 For 1801
Feb 25, 2010
I have a number of Cisco 1801 routers connected to BT UK’s ADSL2+ Annex-A Wholesale Broadband Connect [WBC] services. The routers are experiencing connectivity issues. There is a cisco product bulletin that defines v4.0.0.18 as the version of ADSL Firmware required on the Cisco 1801 when connecting to this BT service.I would like to upgrade the ADSL Firmware for these routers but I cannot find v4.0.0.18 for the Cisco 1801 on CCO. All the 4.0.0.18 downloads appear to be for various flavours of 800. The Cisco product bulletin shows the 1801 as having the same chipset as the 857,867,877 and 887. Can I use the Firmware from one these 800 models? The MD5 Hash for the code suggests all of the these 800 model use the same code?
View 12 Replies
ADVERTISEMENT
Mar 13, 2011
I have multiple customers with either 877 / 1801 routers with dsl issues, we keep dropping sync , get slow speeds etc,
I have already updated to firmware 4.018, in some cases it has resolved the issue in others it has not, BT say their lines are ok, but still i keep getting issues.
View 1 Replies
View Related
Oct 9, 2012
ADSL line do not activate. Telco Confirmed Like is Okay . They have tested no issue observed. Router replaced but did not work. Supspecting Firmware not compatible with telco . Not sure how to confirm on this.
sh ver
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(4)XC7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Tue 31-Jul-07 20:24 by alnguyen
ROM: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
XXXXXXXXXXXXXXXXXXXXXXX uptime is 30 minutes
System returned to ROM by reload at 18:48:26 UTC Wed Oct 10 2012
System image file is "flash:c180x-advipservicesk9-mz.124-4.XC7.bin"(code)
View 1 Replies
View Related
Apr 24, 2012
I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
View 2 Replies
View Related
Feb 1, 2011
Where I can find the change logs for the ADSL Firmware's.I realize each firmware comes with its individual bug fixes, however there is usually a significant difference between the shipped firmware and latest firmware available.i.e. the 877m is shipped with 3.0.14 and the latest is 3.0.33. We have a handfull of miscellaneous issues, across a variety of hardware and customers, and would like to scan through the change logs to see if any of these issues were addressed by a previous bug fix.
View 2 Replies
View Related
May 17, 2010
I cannot find instructions on how to use the latest 4.0.18 ADSL firmware on an 887 router.
I've downloaded adsl_alc_20190_4.0.018.bin from the website and copied it to flash, but cannot find any instructions on applying the firmware. Tried rebooting but made no difference.
What commands, etc, am I meant to use to make use of this ADSL firmware release ?
View 5 Replies
View Related
Mar 28, 2012
Is there a way to find in a remote branch the adsl line number in a cisco router 886VA.
When giving show controllers vdsl 0
we can see the upload/download speed but there is no information about the line number. We need this information in order to troubleshoot adsl line problems with our ISP's in remote branch offices.
View 3 Replies
View Related
Jun 21, 2011
I have a Zoom adsl x6 model 5590 wireless router. I recently tried to update its firmware by following the instructions from the manufacturers site. Everything seemed to go correctly, but I am now unable to connect to the internet or my routers http address. My router now has a red power light along with a solid green light for the wlan and dsl.
View 2 Replies
View Related
Jan 28, 2013
I did not know to update the boot software of my SRW2024 first, then update to 1.2.2b.I need to go back to the 1.0.0.86 firmware.
Is it downloadable and will it work (ie work backwards and then do it properly)? I know how to use hyperterminal and the xmodem protocol if need be.
View 9 Replies
View Related
Jan 27, 2012
I am trying to set up my wireless network but I need updted firmware downloads for the Net Gear modem model CGD24G
View 1 Replies
View Related
Dec 25, 2011
Where can I download firmware? I've been trying to get it through the official site and downloads page, but everytime I click download, then click 'open' there's absolutely nothing in the zip folder (0 bytes).Specifically, I'm looking for the D1 4.11 firmware. It's the one I've been using for about 2 years until needing to reset my router today. And as I forgot how to Hard Reset, I accidently reset everything deleting the firmware too, and I really need the D1 4.11 firmware back as it gave me no issues for 2 years!
View 14 Replies
View Related
Dec 14, 2011
Looking for some old firmware, version 3.2.1.3, any link to where it is?
View 5 Replies
View Related
Mar 31, 2009
Where can I find revision 8 of the WRT160N version 2 firmware?
View 8 Replies
View Related
Jan 29, 2011
i went through the website and figured that my firmware is 1.01.05 and there's a new version availble which is 1.01.09 for my Linksys WAG200G modem since im having problem with unstable connection and now, after i updated the firmware, not only that im dropping connection heaps more, my internet connection has slowed down by alot.
View 2 Replies
View Related
Feb 18, 2012
I have a problem with current (1.0.06) firmware on WRT120N. Few hours after restart DHCP server stops assigning IP addresses. Another restart resolves problem, but only for next few hours.Computers and other devices "see" my wireless network and they are able to connect to it, but the process stops at requesting IP number.There was no such effect with original firmware (although there was another problem with 2200BG), so I want to downgrade.where can I find previous versions of WRT120N firmware?
View 2 Replies
View Related
Jan 23, 2013
I have one of the network every where routers by Linksys, model NR041. I realize this is an older model but it has been good for me ever since I ought it and I am wanting to find a recent firmware upgrade for this. Is anyone aware of a newer firmware upgrade & if so, where can I find it?
View 1 Replies
View Related
Dec 23, 2009
Can't find WAG160N firmware upgrade download page on this site A few mounth ago it existed
View 3 Replies
View Related
Feb 15, 2013
Manual and firmware not available for my f7d2401nt. The US support page do not find the model, the italian support page find the model but link to the US page ! Someone has at least the manual (englis, french or italian language) ?
View 2 Replies
View Related
Nov 6, 2011
Where can i find the lastest version official firmware for my WRT610n V2?
View 9 Replies
View Related
Aug 24, 2012
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies
View Related
Apr 22, 2013
Writing my first router config from scratch for an 1801. I have wireless devices able to connect & authenticate with WPA. Wired devices can talk with wireless devices & on both interfaces devices obtain a DHCP lease. I can ping web based resources from the FA0 interface; the problem is, LAN devices can't ping has FA0. I'm pretty sure (well a hunch) that this is going to be down to NAT
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Router0
.[code]...
View 10 Replies
View Related
Feb 11, 2013
Can a Cisco 1801 FE0 port be sub-interfaced?
View 2 Replies
View Related
Oct 8, 2012
This is my first attempt at configuring an 1801 and I am getting extreamly low bandwidth.Tests show up/down speeds on around 100kbps. I can't see any reason with the possible exception of the show dsl capacity values which never seem to change. How to point out my config error.
View 3 Replies
View Related
Jan 30, 2012
Is it possible to log onto a router over the internet using a pooled IP address? I want to be able to manage some routers that are in different sites, these are just providing internet access to clients. these are 1801 and 877s
View 4 Replies
View Related
Jul 13, 2012
I have a Cisco 1801 that I am trying to set up for my DSL connection. I have configured the router but when I try to access a web site I receive the Http 404 page cannot be displayed error. I have checked my DNS server on the router & I believe that I have configured it correctly? I am hoping that one of you more experienced individual can take a look & tell me where I might have gone wrong. I have included the current running-configuration for your viewing pleasure.
View 4 Replies
View Related
Oct 19, 2011
I'm trying to set up an 1801 router with two WAN interfaces, fastethernet0 and fastethernet1. On the LAN side, I have two subnets. One subnet's internet traffic should be routed over fastethernet0, the other over fastethernet1.I've setup some route maps to accomplish this. I can surf the internet using subnet 192.168.2.0/24 fine, all traffic goes out of fastethernet0. However, and this is where the problem is, if I try to reach the internet using subnet 192.168.3.0/24, all packets go out interface fastethernet0 with the source address of fastethernet1!When I'm surfing the internet, from subnet 192.168.3.0/24, packets should be going out fastethernet1, now they're going out fastethernet0.
View 8 Replies
View Related
Apr 5, 2012
I'm having difficulty logging onto my 1801 router over the internet I can ping the device and tracert to it but I can't telnet or SSH ,Here is the config - Can you see whay this would happen. Its on ADSL link.
View 7 Replies
View Related
Sep 27, 2011
I have two offices - see attached diagram. They use 192.168.0.0/16 for private IP addreses.They're connected via site-to-site VPN. Mostly works well, except some traffic doesn't return and I think it's due to NAT?When a workstation in remote office tries to access web servers in the local office which using private IP addresses (e.g. .64.40), traffic never returns. The web servers in question are also accessible publically - the Cisco 1801 in local office has a static route:
Local1801# ip nat inside source static tcp 192.168.64.40 80 111.111.111.2 80 extendable
The problem seems to be with the local 1801 router. tcpdump confirms that return traffic exits out of ods1's external interface and tcpdump confirms that traffic does not come into remote workstation's interface (neither with .64.40 as source IP nor 111.111.111.2 as source IP)
Remote887# show ip nat translations - none.
Local1801# show ip nat translations
Pro Inside global Inside local Outside local Outside global
tcp 111.111.111.2:80 192.168.64.40:80 192.168.10.254:54990 192.168.10.254:54990
What I don't understand is why a nat translation entry is created. My understanding is that it should only happen when ip packets are sent to 111.111.111.2:80 I don't see that any packets would be sent to this IP address when accessing the site across the VPN - in fact the VPN peer address used is not this one.I cannot figure out why on earth this website cannot be accessed via private IP. I have tried clear ip nat translation * on both routers with no luck.
Relevant Cisco config snippets included below:
Local1801 VPN and NAT config
------------------------------------------
crypto map VPN-MAP 1 ipsec-isakmp
description "Local-Remote VPN"
set peer 222.222.222.222
set transform-set VPN-TRAFFIC
match address 101
[code]....
View 3 Replies
View Related
Jul 16, 2012
we have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:
Encapsulation: PPPoE
Multiplexing: LLC based
VPI = 0
VCI = 103
Login =xxxxx
Password =xxxxx
IP: dynamically from ISP
configuring cisco router 1801 for above configuration.
View 5 Replies
View Related
Jun 10, 2012
when I'm trying to configure my router 1801 with PPPOE I have the message below "% PPPoE config from vpdn-group is converted to pppoe-profile based config.% Continue PPPoE configuration under 'bba-group pppoe global'.
View 3 Replies
View Related
Jun 8, 2011
I have a Cisco 1801 Router, but whenever there is anything plugged into the integrated 8 port switch for example two computers, I cannot get them to ping each other. All of the ports are on the same vLAN.
I am a Cisco newbie, so sorry if this question/query is really basic. Is there anyway I can test the integrated switch to see if it is faulty.
View 17 Replies
View Related
Jun 5, 2012
I have an FTP server that sits behind a cisco 1801 router.But now i want to add in FTP ports 21 and 20. I have added them in but i cant get it working via ftp.If i plug into the LAN and give my laptop an ip address on the same range as the server (192.168.2.100) then FTP works fine -
[code]...
View 3 Replies
View Related
Aug 9, 2011
Network Setup
===========
2 Site to Site VPN tunnels has been established, it is a hub and spoke topology. The hub is ASA5520 and the 2 spoke are a 1841 and 1801 router. The tunnel is able to pass traffic, it's a full tunnel VPN.The tunnel randomly disconnect for no reason. When I check the logs I can see some errors :
%CRYPTO-4-RECVD_PKT_INV_SPI: decaps: rec'd IPSEC packet has invalid spi for destaddr=x.x.x.x, prot=50, spi=0x5F822579(1602364793), srcaddr=y.y.y.y
%CRYPTO-4-IKMP_NO_SA: IKE message from y.y.y.y has no SA and is not an initialization offer
The actual address have been replace by x.x.x.x and y.y.y.y. I frequently have to peform clear crypto isakmp on the spoke routers to revive the VPN tunnels. Is there a way the tunnel can be re-establish again without manual intervention?This keep happening on a random basis and I have living with it for years. I have looked at cisco website troubleshooting tips and but no luck in finding out how to resolve it.
Below is my config on one of the spoke router:
==================================
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)
crypto isakmp policy 10encr 3deshash md5authentication pre-sharegroup 2crypto isakmp key @@@@@@ address y.y.y.ycrypto isakmp invalid-spi-recoverycrypto isakmp keepalive 30 periodiccrypto isakmp nat keepalive 20!!crypto ipsec transform-set tset1 esp-3des esp-md5-hmaccrypto ipsec df-bit clear!crypto map ipsecvpn 10 ipsec-isakmp
set peer y.y.y.yset transform-set tset1match address vpn@spoke!archivelog config hidekeys!!!!!interface FastEthernet0ip address x.x.x.x 255.255.255.248ip nat outsideip virtual-reassemblyduplex autospeed autocrypto map ipsecvpn!interface FastEthernet1!interface FastEthernet2!interface FastEthernet3!interface FastEthernet4!interface FastEthernet5!interface
[code]....
View 4 Replies
View Related
