Cisco :: Configure 1801 For Qwest DSL Connection
Jul 13, 2012
I have a Cisco 1801 that I am trying to set up for my DSL connection. I have configured the router but when I try to access a web site I receive the Http 404 page cannot be displayed error. I have checked my DNS server on the router & I believe that I have configured it correctly? I am hoping that one of you more experienced individual can take a look & tell me where I might have gone wrong. I have included the current running-configuration for your viewing pleasure.
View 4 Replies
ADVERTISEMENT
Jun 10, 2012
when I'm trying to configure my router 1801 with PPPOE I have the message below "% PPPoE config from vpdn-group is converted to pppoe-profile based config.% Continue PPPoE configuration under 'bba-group pppoe global'.
View 3 Replies
View Related
Oct 8, 2012
This is my first attempt at configuring an 1801 and I am getting extreamly low bandwidth.Tests show up/down speeds on around 100kbps. I can't see any reason with the possible exception of the show dsl capacity values which never seem to change. How to point out my config error.
View 3 Replies
View Related
Apr 17, 2008
Here is my current config build for a Cisco 2620 using a Wic-1ADSL to connect to a Qwest ADSL ISP:
interface FastEthernet0/0
ip address 172.16.0.1 255.255.0.0
ip nat inside
no ip mroute-cache
[code]...
For some reason, it won't connect at all. I've changed the callin requirement on the ppp authentication between "callin" to "callout" - even removed the line completely for a no-authentication scenario.The only responses that come back on a repetative nature when doing a debug are:
Vi2 PPP: Authorization NOT required
and
Vi2 PPP: No remote authorization for call-out
View 2 Replies
View Related
Mar 20, 2013
I am trying to setup a cisco 2600 router that will be used to connect to a Qwest internet T1. I will have a Cisco ASA firewall behind the router so that I can build a site to site VPN tunnel. Qwest requires PPP encapsulation. The Lan side network is 10.2.0.0/16. Qwest gave me their serial IP address and my serial ip address which was I used to configure the route. The ethernet interface was configured for the local Lan side subnet and i natted both the inside and outside interface of the router. I am not sure if this is correct. How do I configure the router so that I can use one of the available public IP Addresses as the outside interface of the ASA?
Here is the config of the router:
version 12.2no parser cacheno service single-slot-reload-enableservice timestamps debug uptimeservice timestamps log uptimeno service password-encryption!hostname cedar!logging rate-limit console 10 except errorsenable secret 5 xxxxxxxxxxenable password xxxxxx!ip subnet-zeroip audit notify logip audit po max-events 100no ip dhcp-client network-discoverycall rsvp-syncinterface FastEthernet0/0description Lan Interfaceip address 10.2.1.1 255.255.255.0ip nat insideno ip route-cacheno ip mroute-cachespeed autofull-duplexno mop enabled!interface Serial0/0ip address 65.121.x.x 255.255.255.252ip nat outsideencapsulation pppfair-queueservice-module t1 clock source internalservice-module t1 timeslots 1-24!ip nat inside source list 1 interface Serial0/0 overloadip classlessip route 0.0.0.0 0.0.0.0 65.121.x.x (qwest serial IP address)ip http serverip http authentication local!access-list 1 permit 0.0.0.0 255.255.0.0
View 7 Replies
View Related
Jan 10, 2012
trying to set up my router from the qwest modem
View 1 Replies
View Related
May 3, 2011
I have been working on this problem for the last few day and have know idea why its not working but my d link Dir-615 will not work with my qwest q100 modem.
View 1 Replies
View Related
May 13, 2011
i have the qwest q100 modem and my freind happened to havea qwest q1000 modem and when i just connected the q1000 the internet doesnt work. what do i do?
View 2 Replies
View Related
Aug 9, 2011
I am running Windows Vista service pack 2 using my laptop - Hp Pavilion dv5-1111ea and I have a qwest actiontec gt701-wg router. When I try to connect to the router it says connected to local only and when I diagonise the connection it says that Security policy seetings on this computer might be blocking the connection.
The following policy might need to be adjusted to allow windows to connect: Policy Provider:Windows Firewall Filter Name: Query User
View 12 Replies
View Related
Feb 5, 2012
Dell dimension 2400 XP home. Connects fine to old linksys g router.With new qwest dsl modem/router get IRQL not less than or equal as soon as I click on connect .Blue screen stop and must reboot.Qwest router works fine with my lenovo lap top. Win 7.
View 3 Replies
View Related
Jan 3, 2012
I have a Cisco 678 connected to my ISP (Qwest) using DHCP. This is connected to a Linksys WRT54g router. I also have a home server running for remote access to some files and media streaming. I just installed security cameras that I wish to monitor remotely via the internet.I can access my home files over the internet with no issue. However I am unable to access my cameras using the internet. Looking at my router incoming log, I see my request arriving, but I never get to the DVR attached to the camereas for remote viewing.I enabled bridging on the Cisco 678 but this did not solve the issue.
View 1 Replies
View Related
Dec 31, 2012
i have an Iomega Prestige Desktop External Hard drive usb 2.0.I also have a quest-centurylink ZyXEL modem model #PK5000Z.I would like to connect the iomega to the modem. However, I don't see a usb port on the modem.
View 1 Replies
View Related
Oct 7, 2011
Ok, my roomate is hogging the bandwidth on our shared router downloading junk. I'm not sure if he's using a torrent, but just in case he is here is my question:How do I turn off the ports for torrenting on my qwest pk5000 modem? Is there anything else I can do that would work as well?My friend reccommended I turn off every port after 9000 or something.
View 3 Replies
View Related
Oct 1, 2012
port forwarding this im trying to setup a minecraft server with bukkit and i tried a number of things to port forward and it won't open port. I have a tomato firmware linksys router and a qwest modem.
View 1 Replies
View Related
Apr 22, 2013
Writing my first router config from scratch for an 1801. I have wireless devices able to connect & authenticate with WPA. Wired devices can talk with wireless devices & on both interfaces devices obtain a DHCP lease. I can ping web based resources from the FA0 interface; the problem is, LAN devices can't ping has FA0. I'm pretty sure (well a hunch) that this is going to be down to NAT
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Router0
.[code]...
View 10 Replies
View Related
Feb 11, 2013
Can a Cisco 1801 FE0 port be sub-interfaced?
View 2 Replies
View Related
Jan 30, 2012
Is it possible to log onto a router over the internet using a pooled IP address? I want to be able to manage some routers that are in different sites, these are just providing internet access to clients. these are 1801 and 877s
View 4 Replies
View Related
Oct 19, 2011
I'm trying to set up an 1801 router with two WAN interfaces, fastethernet0 and fastethernet1. On the LAN side, I have two subnets. One subnet's internet traffic should be routed over fastethernet0, the other over fastethernet1.I've setup some route maps to accomplish this. I can surf the internet using subnet 192.168.2.0/24 fine, all traffic goes out of fastethernet0. However, and this is where the problem is, if I try to reach the internet using subnet 192.168.3.0/24, all packets go out interface fastethernet0 with the source address of fastethernet1!When I'm surfing the internet, from subnet 192.168.3.0/24, packets should be going out fastethernet1, now they're going out fastethernet0.
View 8 Replies
View Related
Apr 5, 2012
I'm having difficulty logging onto my 1801 router over the internet I can ping the device and tracert to it but I can't telnet or SSH ,Here is the config - Can you see whay this would happen. Its on ADSL link.
View 7 Replies
View Related
Sep 27, 2011
I have two offices - see attached diagram. They use 192.168.0.0/16 for private IP addreses.They're connected via site-to-site VPN. Mostly works well, except some traffic doesn't return and I think it's due to NAT?When a workstation in remote office tries to access web servers in the local office which using private IP addresses (e.g. .64.40), traffic never returns. The web servers in question are also accessible publically - the Cisco 1801 in local office has a static route:
Local1801# ip nat inside source static tcp 192.168.64.40 80 111.111.111.2 80 extendable
The problem seems to be with the local 1801 router. tcpdump confirms that return traffic exits out of ods1's external interface and tcpdump confirms that traffic does not come into remote workstation's interface (neither with .64.40 as source IP nor 111.111.111.2 as source IP)
Remote887# show ip nat translations - none.
Local1801# show ip nat translations
Pro Inside global Inside local Outside local Outside global
tcp 111.111.111.2:80 192.168.64.40:80 192.168.10.254:54990 192.168.10.254:54990
What I don't understand is why a nat translation entry is created. My understanding is that it should only happen when ip packets are sent to 111.111.111.2:80 I don't see that any packets would be sent to this IP address when accessing the site across the VPN - in fact the VPN peer address used is not this one.I cannot figure out why on earth this website cannot be accessed via private IP. I have tried clear ip nat translation * on both routers with no luck.
Relevant Cisco config snippets included below:
Local1801 VPN and NAT config
------------------------------------------
crypto map VPN-MAP 1 ipsec-isakmp
description "Local-Remote VPN"
set peer 222.222.222.222
set transform-set VPN-TRAFFIC
match address 101
[code]....
View 3 Replies
View Related
Jul 16, 2012
we have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:
Encapsulation: PPPoE
Multiplexing: LLC based
VPI = 0
VCI = 103
Login =xxxxx
Password =xxxxx
IP: dynamically from ISP
configuring cisco router 1801 for above configuration.
View 5 Replies
View Related
Feb 25, 2010
I have a number of Cisco 1801 routers connected to BT UK’s ADSL2+ Annex-A Wholesale Broadband Connect [WBC] services. The routers are experiencing connectivity issues. There is a cisco product bulletin that defines v4.0.0.18 as the version of ADSL Firmware required on the Cisco 1801 when connecting to this BT service.I would like to upgrade the ADSL Firmware for these routers but I cannot find v4.0.0.18 for the Cisco 1801 on CCO. All the 4.0.0.18 downloads appear to be for various flavours of 800. The Cisco product bulletin shows the 1801 as having the same chipset as the 857,867,877 and 887. Can I use the Firmware from one these 800 models? The MD5 Hash for the code suggests all of the these 800 model use the same code?
View 12 Replies
View Related
Jun 8, 2011
I have a Cisco 1801 Router, but whenever there is anything plugged into the integrated 8 port switch for example two computers, I cannot get them to ping each other. All of the ports are on the same vLAN.
I am a Cisco newbie, so sorry if this question/query is really basic. Is there anyway I can test the integrated switch to see if it is faulty.
View 17 Replies
View Related
Oct 9, 2012
ADSL line do not activate. Telco Confirmed Like is Okay . They have tested no issue observed. Router replaced but did not work. Supspecting Firmware not compatible with telco . Not sure how to confirm on this.
sh ver
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(4)XC7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Tue 31-Jul-07 20:24 by alnguyen
ROM: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
XXXXXXXXXXXXXXXXXXXXXXX uptime is 30 minutes
System returned to ROM by reload at 18:48:26 UTC Wed Oct 10 2012
System image file is "flash:c180x-advipservicesk9-mz.124-4.XC7.bin"(code)
View 1 Replies
View Related
Jun 5, 2012
I have an FTP server that sits behind a cisco 1801 router.But now i want to add in FTP ports 21 and 20. I have added them in but i cant get it working via ftp.If i plug into the LAN and give my laptop an ip address on the same range as the server (192.168.2.100) then FTP works fine -
[code]...
View 3 Replies
View Related
Aug 9, 2011
Network Setup
===========
2 Site to Site VPN tunnels has been established, it is a hub and spoke topology. The hub is ASA5520 and the 2 spoke are a 1841 and 1801 router. The tunnel is able to pass traffic, it's a full tunnel VPN.The tunnel randomly disconnect for no reason. When I check the logs I can see some errors :
%CRYPTO-4-RECVD_PKT_INV_SPI: decaps: rec'd IPSEC packet has invalid spi for destaddr=x.x.x.x, prot=50, spi=0x5F822579(1602364793), srcaddr=y.y.y.y
%CRYPTO-4-IKMP_NO_SA: IKE message from y.y.y.y has no SA and is not an initialization offer
The actual address have been replace by x.x.x.x and y.y.y.y. I frequently have to peform clear crypto isakmp on the spoke routers to revive the VPN tunnels. Is there a way the tunnel can be re-establish again without manual intervention?This keep happening on a random basis and I have living with it for years. I have looked at cisco website troubleshooting tips and but no luck in finding out how to resolve it.
Below is my config on one of the spoke router:
==================================
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)
crypto isakmp policy 10encr 3deshash md5authentication pre-sharegroup 2crypto isakmp key @@@@@@ address y.y.y.ycrypto isakmp invalid-spi-recoverycrypto isakmp keepalive 30 periodiccrypto isakmp nat keepalive 20!!crypto ipsec transform-set tset1 esp-3des esp-md5-hmaccrypto ipsec df-bit clear!crypto map ipsecvpn 10 ipsec-isakmp
set peer y.y.y.yset transform-set tset1match address vpn@spoke!archivelog config hidekeys!!!!!interface FastEthernet0ip address x.x.x.x 255.255.255.248ip nat outsideip virtual-reassemblyduplex autospeed autocrypto map ipsecvpn!interface FastEthernet1!interface FastEthernet2!interface FastEthernet3!interface FastEthernet4!interface FastEthernet5!interface
[code]....
View 4 Replies
View Related
Mar 13, 2011
I have multiple customers with either 877 / 1801 routers with dsl issues, we keep dropping sync , get slow speeds etc,
I have already updated to firmware 4.018, in some cases it has resolved the issue in others it has not, BT say their lines are ok, but still i keep getting issues.
View 1 Replies
View Related
May 12, 2012
I have configured the following access-list on routers fa0 interface (i am using 1801)
access-list 111 permit ip any any log
and applied it in "in" direction on Fa0 interface.
Now when i am sending ssh packets to this interface its showing below
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
why its not showing any port number ?
View 1 Replies
View Related
Apr 24, 2012
I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
View 2 Replies
View Related
May 21, 2012
I am wondering what are the limits per routers for creating the vlans in vlan database? I have a 1801 router with the c180x-broadband-mz.151-3.T2 IOS and cant create more than 14 vlans.. How many does 2800 router support? Why I can't find this information anywhere on cisco.com?
View 7 Replies
View Related
Jul 4, 2012
I'm trying to use Cisco IP SLA to bench mark voice traffic peformance before and after I apply QoS to the network.
* I've setup IP SLA in both directions over a DSL connection between a 7600, and an 1801
* I've setup IP SLA in both directions over an Ethernet WAN link between a 7200 and another 7200
ip sla 1
udp-jitter 10.101.1.1 32770 source-ip 10.101.2.1 source-port 32770 codec g711alaw
frequency 30
!
ip sla schedule 1 life forever start-time now
!
ip sla responder
!
I have a problem in that I'm not getting any meaningful data from the IP SLA statistics for Voice Score Values:, or any data for Latency one-way time: for any of my tests(x 4).
After a day of testing it seems the MOS score never changes from 4.34, and the ICPIF never changes from 1 ?Is there something wrong with my config? Is this working properly or could this be a bug?
ADSL-R1#show ip sla statistics 1 details
Round Trip Time (RTT) for Index 1
Latest RTT: 48 milliseconds
Latest operation start time: *09:27:48.435 UTC Thu Jul 5 2012
Latest operation return code: OK
Over thresholds occurred: FALSE
[code]....
View 3 Replies
View Related
May 26, 2012
I have a cisco 1801 (fixed), and want to use the fe0 WAN port to connect to the internet via a virgin media cable modem.
I am having a few issues (partly as I am new to cisco) and despite reading numerous posts both here and other sites, I am still stuck on how to setup the WAN side, I have read about virtual dial up & dialer interface.
View 1 Replies
View Related
May 28, 2013
I have been struggling to find a DDNS provider from which the IP address can be updated from a Cisco device.One does not seem to support it, (Free-DDNS) other must be paid for (No-IP.org) while the free version does not update the IP address in my case, etc, etc.The device that is directly behind my modem is a Cisco 1801 router.My question is, which DDNS provider works for you when auto-updating the IP address via the Cisco router?
View 1 Replies
View Related
