Cisco :: 7600 / 1801 - IP SLA Stats - One Way Latency / MOS Score 4.34 Not Updating?
Jul 4, 2012
I'm trying to use Cisco IP SLA to bench mark voice traffic peformance before and after I apply QoS to the network.
* I've setup IP SLA in both directions over a DSL connection between a 7600, and an 1801
* I've setup IP SLA in both directions over an Ethernet WAN link between a 7200 and another 7200
ip sla 1
udp-jitter 10.101.1.1 32770 source-ip 10.101.2.1 source-port 32770 codec g711alaw
frequency 30
!
ip sla schedule 1 life forever start-time now
!
ip sla responder
!
I have a problem in that I'm not getting any meaningful data from the IP SLA statistics for Voice Score Values:, or any data for Latency one-way time: for any of my tests(x 4).
After a day of testing it seems the MOS score never changes from 4.34, and the ICPIF never changes from 1 ?Is there something wrong with my config? Is this working properly or could this be a bug?
ADSL-R1#show ip sla statistics 1 details
Round Trip Time (RTT) for Index 1
Latest RTT: 48 milliseconds
Latest operation start time: *09:27:48.435 UTC Thu Jul 5 2012
Latest operation return code: OK
Over thresholds occurred: FALSE
I have been struggling to find a DDNS provider from which the IP address can be updated from a Cisco device.One does not seem to support it, (Free-DDNS) other must be paid for (No-IP.org) while the free version does not update the IP address in my case, etc, etc.The device that is directly behind my modem is a Cisco 1801 router.My question is, which DDNS provider works for you when auto-updating the IP address via the Cisco router?
I've got as Cisco AS5400 Ver 12.3(22) with the E1 controllers acting as ISUP TG (pri-groups). Since we have no streaming for call records to RADIUS serving etc. is there a way to setup a log or history buffer for alerts for traffic congestion? With high call rates the "normal" realtime methods of using >sh call active voice breif | i No Circuit Avail wouldn't be pratical since memory/processor usage could be an issue. The >debug isdn q931 interf dch 1/0 would of worked but again so much traffic is coming I don't want to increase the size of the logg buff >300K.I guess I was expecting an easy way out being an old TDM salt used to the 5E/Telica Plexview/DMS having CDR and Traffic Stat info readily available. I know the AS5400 is a powerful device, maybe I just haven't got the right command down or totally overlooked the obvious.Oh, and this is connected to the Cisco PGW/SGC 2200 Version:"9.3(2) and I haven't found anything in it's logs. [code]
I was just wondering on the stats page of my DIR-615 the WAN Stats is in packets. How do I convert that into megabytes and gigabytes so I can track my usage?
Since AT&T put in caps and do not provide a usage meter. I would like to keep track of my usage.
I have a Cisco 2621XM router with two ethernet interfaces that sits before a vendor supplied VPN router. I need to see the IP traffic incoming to my router from the WAN side (fasteth0/1 below). I setup ip cef, and ip flow ingress on the interface. However -- it seems that what I see when I use "ip cache flow" command doesn't have a very long history or life. What commands am I missing so that I can see a summary of the stats over say the last 5, 10 or 15 minutes? Is this the best config that can be used for this, or can I create a more summarized report just using the router HW and IOS? Basic current configuration:version 12.3service timestamps debug uptimeservice timestamps log uptimeservice password-encryption!hostname Littleboy!ip subnet-zeroip cef table event-log size 1024ip cefip cef accounting per-prefix non-recursive prefix-lengthip cef traffic-statistics load-interval 180!ip flow-cache entries 2048ip flow-cache timeout inactive 60!interface FastEthernet0/1 description Littleboy to vpn-wan ip address 10.1.0.1 255.255.255.252 ip flow ingress?
Is there a good reference in how to interpret the "show AP stats" command?
I have a new (online for 15 days) 1142 listed below. It is the first 802.11n AP I've deployed. The stat counters look bad [code] But I don't know how to put it all together to say "here are the stats, this is the problem". I see TxFrameCount, but no corresponding RxFrameCount, so it is hard to calibrate some of the errors. [code]
I've got a WRVS4400N wireless router running DHCP for a couple dozen wireless clients in a public library. We need to gather statistics on the wireless clients on a daily basis: average number of clients, max number of clients, average time used per client etc.
The router only gives a list of clients currently allocated an IP address, but there doesn't seem to be a way to gather statistics over time. Is there a program that will interface with the router to gather more detailed statistics?
I am using a E3000 router with a Draytek V120 modem and I need to get some line stats for my ISP to sort out a problem however I cant see how to get stats out of the E3000, simple but having been through all the settings in the web interface I cant find it.
I notice that I have TX Packets Dropped only under the wireless section.This occurs when the wireless network is not in use also.I have tried many different channels, almost all of them.Im using wpa2-tkip+aes, mixed g and n network, auto 20/40, wps disabled.I understand about wireless interference also.wireless devices dont seem to have any issues though, not dropping from network.I usually get 4000 wireless TX drops a day. LAN and WAN show No TX drops
On my old router I could access the line stats on the home page giving me Attenuation and SNR margin, this allowed me to keep an eye on line quality, there seems to be no equivalent info on the X2000. Is this on a hidden page like the advanced wireless page.
In our environment we have some HP chassis, and with them there are blade switches. Lately, we've been seeing some drops on few servers connected on the blade switch ports. The switch model is WS-CBS3120X-S. And below is the tx drop for two interfaces ( where the servers are connected to).
Writing my first router config from scratch for an 1801. I have wireless devices able to connect & authenticate with WPA. Wired devices can talk with wireless devices & on both interfaces devices obtain a DHCP lease. I can ping web based resources from the FA0 interface; the problem is, LAN devices can't ping has FA0. I'm pretty sure (well a hunch) that this is going to be down to NAT
version 12.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname Router0
This is my first attempt at configuring an 1801 and I am getting extreamly low bandwidth.Tests show up/down speeds on around 100kbps. I can't see any reason with the possible exception of the show dsl capacity values which never seem to change. How to point out my config error.
Is it possible to log onto a router over the internet using a pooled IP address? I want to be able to manage some routers that are in different sites, these are just providing internet access to clients. these are 1801 and 877s
I have a Cisco 1801 that I am trying to set up for my DSL connection. I have configured the router but when I try to access a web site I receive the Http 404 page cannot be displayed error. I have checked my DNS server on the router & I believe that I have configured it correctly? I am hoping that one of you more experienced individual can take a look & tell me where I might have gone wrong. I have included the current running-configuration for your viewing pleasure.
I'm trying to set up an 1801 router with two WAN interfaces, fastethernet0 and fastethernet1. On the LAN side, I have two subnets. One subnet's internet traffic should be routed over fastethernet0, the other over fastethernet1.I've setup some route maps to accomplish this. I can surf the internet using subnet 192.168.2.0/24 fine, all traffic goes out of fastethernet0. However, and this is where the problem is, if I try to reach the internet using subnet 192.168.3.0/24, all packets go out interface fastethernet0 with the source address of fastethernet1!When I'm surfing the internet, from subnet 192.168.3.0/24, packets should be going out fastethernet1, now they're going out fastethernet0.
I'm having difficulty logging onto my 1801 router over the internet I can ping the device and tracert to it but I can't telnet or SSH ,Here is the config - Can you see whay this would happen. Its on ADSL link.
I have two offices - see attached diagram. They use 192.168.0.0/16 for private IP addreses.They're connected via site-to-site VPN. Mostly works well, except some traffic doesn't return and I think it's due to NAT?When a workstation in remote office tries to access web servers in the local office which using private IP addresses (e.g. .64.40), traffic never returns. The web servers in question are also accessible publically - the Cisco 1801 in local office has a static route:
The problem seems to be with the local 1801 router. tcpdump confirms that return traffic exits out of ods1's external interface and tcpdump confirms that traffic does not come into remote workstation's interface (neither with .64.40 as source IP nor 111.111.111.2 as source IP)
Remote887# show ip nat translations - none. Local1801# show ip nat translations Pro Inside global Inside local Outside local Outside global tcp 111.111.111.2:80 192.168.64.40:80 192.168.10.254:54990 192.168.10.254:54990
What I don't understand is why a nat translation entry is created. My understanding is that it should only happen when ip packets are sent to 111.111.111.2:80 I don't see that any packets would be sent to this IP address when accessing the site across the VPN - in fact the VPN peer address used is not this one.I cannot figure out why on earth this website cannot be accessed via private IP. I have tried clear ip nat translation * on both routers with no luck.
Relevant Cisco config snippets included below:
Local1801 VPN and NAT config ------------------------------------------ crypto map VPN-MAP 1 ipsec-isakmp description "Local-Remote VPN" set peer 222.222.222.222 set transform-set VPN-TRAFFIC match address 101
I have a number of Cisco 1801 routers connected to BT UK’s ADSL2+ Annex-A Wholesale Broadband Connect [WBC] services. The routers are experiencing connectivity issues. There is a cisco product bulletin that defines v4.0.0.18 as the version of ADSL Firmware required on the Cisco 1801 when connecting to this BT service.I would like to upgrade the ADSL Firmware for these routers but I cannot find v4.0.0.18 for the Cisco 1801 on CCO. All the 4.0.0.18 downloads appear to be for various flavours of 800. The Cisco product bulletin shows the 1801 as having the same chipset as the 857,867,877 and 887. Can I use the Firmware from one these 800 models? The MD5 Hash for the code suggests all of the these 800 model use the same code?
when I'm trying to configure my router 1801 with PPPOE I have the message below "% PPPoE config from vpdn-group is converted to pppoe-profile based config.% Continue PPPoE configuration under 'bba-group pppoe global'.
I have a Cisco 1801 Router, but whenever there is anything plugged into the integrated 8 port switch for example two computers, I cannot get them to ping each other. All of the ports are on the same vLAN.
I am a Cisco newbie, so sorry if this question/query is really basic. Is there anyway I can test the integrated switch to see if it is faulty.
ADSL line do not activate. Telco Confirmed Like is Okay . They have tested no issue observed. Router replaced but did not work. Supspecting Firmware not compatible with telco . Not sure how to confirm on this.
sh ver Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(4)XC7, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Tue 31-Jul-07 20:24 by alnguyen ROM: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2) XXXXXXXXXXXXXXXXXXXXXXX uptime is 30 minutes System returned to ROM by reload at 18:48:26 UTC Wed Oct 10 2012 System image file is "flash:c180x-advipservicesk9-mz.124-4.XC7.bin"(code)
I have an FTP server that sits behind a cisco 1801 router.But now i want to add in FTP ports 21 and 20. I have added them in but i cant get it working via ftp.If i plug into the LAN and give my laptop an ip address on the same range as the server (192.168.2.100) then FTP works fine -
2 Site to Site VPN tunnels has been established, it is a hub and spoke topology. The hub is ASA5520 and the 2 spoke are a 1841 and 1801 router. The tunnel is able to pass traffic, it's a full tunnel VPN.The tunnel randomly disconnect for no reason. When I check the logs I can see some errors :
%CRYPTO-4-RECVD_PKT_INV_SPI: decaps: rec'd IPSEC packet has invalid spi for destaddr=x.x.x.x, prot=50, spi=0x5F822579(1602364793), srcaddr=y.y.y.y %CRYPTO-4-IKMP_NO_SA: IKE message from y.y.y.y has no SA and is not an initialization offer
The actual address have been replace by x.x.x.x and y.y.y.y. I frequently have to peform clear crypto isakmp on the spoke routers to revive the VPN tunnels. Is there a way the tunnel can be re-establish again without manual intervention?This keep happening on a random basis and I have living with it for years. I have looked at cisco website troubleshooting tips and but no luck in finding out how to resolve it.
I have multiple customers with either 877 / 1801 routers with dsl issues, we keep dropping sync , get slow speeds etc,
I have already updated to firmware 4.018, in some cases it has resolved the issue in others it has not, BT say their lines are ok, but still i keep getting issues.
I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief Interface IP-Address OK? Method Status Protocol FastEthernet0 unassigned YES DHCP up up BRI0 unassigned YES unset administratively down down BRI0:1 unassigned YES unset administratively down down BRI0:2 unassigned YES unset administratively down down
I am wondering what are the limits per routers for creating the vlans in vlan database? I have a 1801 router with the c180x-broadband-mz.151-3.T2 IOS and cant create more than 14 vlans.. How many does 2800 router support? Why I can't find this information anywhere on cisco.com?
I have a cisco 1801 (fixed), and want to use the fe0 WAN port to connect to the internet via a virgin media cable modem.
I am having a few issues (partly as I am new to cisco) and despite reading numerous posts both here and other sites, I am still stuck on how to setup the WAN side, I have read about virtual dial up & dialer interface.
