Cisco Switching / Routing :: 1801 Router - Add In FTP Ports 21 And 20?

Jun 5, 2012

I have an FTP server that sits behind a cisco 1801 router.But now i want to add in FTP ports 21 and 20.  I have added them in but i cant get it working via ftp.If i plug into the LAN and give my laptop an ip address on the same range as the server (192.168.2.100) then FTP works fine -

[code]...

View 3 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 1801 Router Integrated Into Home Network?

Jan 8, 2012

I came accross a Cisco 1801 router. As I understand it supposed to work with a dsl connection for internet access and configuration. I have cable internet access at home and since cisco routers are very versatile, I want to know if I can integrate this router into my home network, as a secondary router, and use it for its SSL vpn capabilities?

View 11 Replies View Related

Cisco Switching/Routing :: 2960 / 1801 - Switch / Router VLAN Configuration

Jul 5, 2012

I've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1. 

The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.

Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0  disabled. In trying to get the switch to communicate with the router I made the following router config modifications. 

FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27

I have two issues I want to resolve: 
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.

View 2 Replies View Related

Cisco Switching/Routing :: Test Multicast Routing With 1801?

Apr 29, 2012

I would like test multicast routing with cisco1801.i create 2 Vlan. Vlan 200 (192.168.200.x) affect Fastethernet 1,  Vlan 130  (192.168.130.x) Fastethernet 5.

Version IOS is : adipservice-k9 124-9.t1

 ip multicast-routing
 
#int Vlan 130
  ip address 192.168.130.254 255.255.255.0
  Ip pim dense-mode
#int Vlan 200
  Ip address 192.168.200.254 255.255.255.0
  Ip pim dense-mode
 
I used VLC for my test.When i connect source (224.10.10.10) and recever ( Udp://@224.10.10.10:1234), that's ok!But, source is on the Vlan 200 and reicever on the Vlan 130, is not good!I test with "sparse-mode", i have same problem.

View 2 Replies View Related

Cisco Switching/Routing :: 1801 Not Showing Any Port Number?

May 12, 2012

I have configured the following access-list on routers fa0 interface (i am using 1801)
 
access-list 111 permit ip any any log
 
and applied it in "in" direction on Fa0 interface.
 
Now when i am sending ssh packets to this interface its showing below
 
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
 
why its not showing any port number ?

View 1 Replies View Related

Cisco Switching/Routing :: ADSL On Fast Ethernet In 1801?

Apr 24, 2012

I have cisco 1801W . Earlier I am using ADSL dynamic IP address  on RJ 11  through the ADSL Port but now the ISP change the connection to RJ45.
 
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
 
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.  
 
Router#show ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0              unassigned      YES DHCP   up                    up
BRI0                       unassigned      YES unset  administratively down down
BRI0:1                     unassigned      YES unset  administratively down down
BRI0:2                     unassigned      YES unset  administratively down down

[code].....

View 2 Replies View Related

Cisco Switching/Routing :: 1801 - VLan Database Limits

May 21, 2012

I am wondering what are the limits per routers for creating the vlans in vlan database? I have a 1801 router with the c180x-broadband-mz.151-3.T2 IOS and cant create more than 14 vlans.. How many does 2800 router support? Why I can't find this information anywhere on cisco.com?

View 7 Replies View Related

Cisco Switching/Routing :: 1801 - How To Connect Fe0 Wan Port To Internet

May 26, 2012

I have a cisco 1801 (fixed), and want to use the fe0 WAN port to connect to the internet via a virgin media cable modem.
 
I am having a few issues (partly as I am new to cisco) and despite reading numerous posts both here and other sites, I am still stuck on how to setup the WAN side, I have read about virtual dial up & dialer interface.

View 1 Replies View Related

Cisco Switching/Routing :: Can SM-ES3G-16-P Act As L3 Ports For Router

Mar 27, 2013

I have a SM-ES3G-16-P in a 2951. Is there any way that the service module interfaces can be transparent to the host router. Essentially I want the SM to act like an HWIC-1GE .. only with more ports!

View 4 Replies View Related

Cisco Switching/Routing :: Simple Way Of Opening Ports On 1841 Router

May 12, 2012

Any simple way of opening ports on a 1841 router.I have a working config for internet traffic. I am looking to boot up my Windows Server and Run IIS.

View 1 Replies View Related

Cisco Switching/Routing :: Pass Vlans Across FE Ports On 1841 Router?

Nov 6, 2012

due to upcoming changes to our network I'd like to be able to pass vlans across the FE ports of a Cisco 1841 router.1 port would go to a managed switch and then to local devices on different VLANs.the 2nd port would go upstream to a Cisco 3825 at a different location which would then connect to the internet.due to monitoring behind the Cisco3825 we would like all NAT to occur on the 3825.
 
what I would like to happen is this example device connected to port 7 on managed switch gets an IP (10.0.7.10) from the Cisco 1841 in VLAN 7 (10.0.7.0/24).traffic from that device goes to the switch, then in f0/1 on the 1841 and out f0/0 still with the same IP info, no NAT occuring.traffic is received on the 3825 port 0/1 and then NAT occurs and out port 0/0 to the internet.

View 4 Replies View Related

Cisco Switching/Routing :: To Configure Multiple LAN Ports On Router With Same 2921

Mar 10, 2013

I have 2921 router and I have 3 very basic switches that I need to connect to the router. The switches have very basic default configurations and there is no way to edit them, so I only have one VLAN and one default gateway. I can't assign the same IP address to each LAN port. I'm not sure how to make this setup work.

View 12 Replies View Related

Cisco Switching/Routing :: 2600 Switch Ports Don't Even Show Up On Router Config

Jan 10, 2012

My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16).   This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary.  Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules.  I think I made an error when I purchased a few of these switch modules:  NME-16ES-1G.   
 
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart).  I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way.  I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16.  (Note:  The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
 
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch.  It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet.  So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]

View 4 Replies View Related

Cisco Switching/Routing :: Open Specific Ports On 1941w Integrated Services Router

Apr 20, 2013

open specific ports on 1941w Integrated Services Router.This specific router is a wireless VPN router that has a wired module and a wireless module and VPN so I'm getting 3 subnets on my network - 192.168.1.. for the wired connections, 10.100.1.... for wireless LAN connections and 10.100.2... for VPN remote connections.I know that by default all connected computers can access my Linux server data through telnet so the telnet port is open by default, the problem is that I have some other software licensing system on my Linux box that needs to be accessed through port 27000 and most of my users are using wireless connections and can't access that license because post 27000 is closed.what is the comand to open this post or any other port that I need to be open on the wired module, wireless module and VPN or at least poit me to somewhere where I can find all the commands that I can use for this router?

View 6 Replies View Related

Cisco WAN :: 1801 - Log On To Router Remotely

Jan 30, 2012

Is it possible to log onto a router over the internet using a pooled IP address? I want to be able to manage some routers that are in different sites, these are just providing internet access to clients. these are 1801 and 877s

View 4 Replies View Related

Cisco WAN :: 1801 Router Setting Up With Two WAN Interfaces

Oct 19, 2011

I'm trying to set up an 1801 router with two WAN interfaces, fastethernet0 and fastethernet1. On the LAN side, I have two subnets. One subnet's internet traffic should be routed over fastethernet0, the other over fastethernet1.I've setup some route maps to accomplish this. I can surf the internet using subnet 192.168.2.0/24 fine, all traffic goes out of fastethernet0. However, and this is where the problem is, if I try to reach the internet using subnet 192.168.3.0/24, all packets go out interface fastethernet0 with the source address of fastethernet1!When I'm surfing the internet, from subnet 192.168.3.0/24, packets should be going out fastethernet1, now they're going out fastethernet0.

View 8 Replies View Related

Cisco WAN :: 1801 Cannot Telnet Or SSH Onto Router Over Internet

Apr 5, 2012

I'm having difficulty logging onto my 1801 router over the internet I can ping the device and tracert to it but I can't telnet or SSH ,Here is the config - Can you see whay this would happen. Its on ADSL link.

View 7 Replies View Related

Cisco WAN :: Configuring 1801 Router For PPPoE?

Jul 16, 2012

we have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:
 
Encapsulation:  PPPoE
Multiplexing:  LLC based
VPI = 0
VCI = 103
Login =xxxxx
Password =xxxxx
IP:  dynamically from ISP
 
configuring cisco router 1801 for above configuration.                  

View 5 Replies View Related

Cisco WAN :: Configure Router 1801 With PPPOE

Jun 10, 2012

 when I'm trying to configure my router 1801 with PPPOE  I have the message below "% PPPoE config from vpdn-group is converted to pppoe-profile based config.% Continue PPPoE configuration under 'bba-group pppoe global'.

View 3 Replies View Related

Cisco Switching/Routing :: 2960 - Ports Going Up And Down?

Nov 7, 2012

we hava a couple of 2960 switches and we are logging to a syslog server. Ports keep going up and down is it normal severity (error)   ?

View 2 Replies View Related

Cisco Switching/Routing :: SG-300 - Switch With 24 SFP Ports

Nov 9, 2011

I like the SG-300 switches for SMB and I'd like use them in our network. Design is quite simple just 6 SG-300 switches connected to one central switch using SFP ports (using 2 port trunks) so I need 12 SFP ports and this is my question. Could you recomend me switch with more then 12 SFP ports from Cisco for this SMB network ? I don't know all the Cisco product lines and I can't find it.

View 2 Replies View Related

Cisco Switching/Routing :: 3560CPD Ports Won't Come On?

Sep 16, 2012

I'm currently having a problem getting the ports on a 3560CPD (ports 1-8) to power on and establish connectivity. I have them hookedup and TURNED on by a 3560 PoE 8 port switch via the uplink ports. I can console into the CPD switch just fine and getting it configured.. but when I connect anything to the ports (1-8) I'm not getting any indicator lights.

View 1 Replies View Related

Cisco Switching/Routing :: 10G Ports On Nexus 7K?

Jul 2, 2012

I''ve trying to bring up ports on a N7K-M108X2-12L card using X2-10GB-SR modules.
 
All ports are in a VDC and configured to accept the M1 card:
 
vdc_id  vdc_name                          state               mac                 type        lc
------  --------                          -----               ----------          ---------   ------
2       cam-cor-csw-sfy-01                active              64:a0:e7:43:f0:c2   Ethernet    m1 f1 m1xl

[Code]....

View 3 Replies View Related

Cisco Switching/Routing :: How To Segment The Ports On SF-300 Switch

Jul 13, 2012

The default Gateway and DHCP server is connected to port 1 of the switch.  I have various other devices on the network plugged into other ports on the switch.I want port 1 to communicate with every port on the switch, but don't want the other ports to be able to see eachother unless I specifically allow them to. For example, port 5 should see port 1, and 7, but nothing else.Everything needs to be in the same subnet.  With the older Dlink switches I am used to this feature is called "Port Segmentation" but I see no such option in this switch.   I have been playing with the VLAN settings but so far I have not been able to achieve this.

View 7 Replies View Related

Cisco Switching/Routing :: 4500 - How To Configure The SFP Ports

May 23, 2012

How i can  configure the SFP Ports on my 4500 SERIES CHASSIS with other SFP ports on the connecting switch. I want to connect 15 switches via GLC=SX=MM to my 4506E sfp card.

View 4 Replies View Related

Cisco Switching/Routing :: 2960 Switch Ports Using POE?

Feb 5, 2013

I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
 
Gi3/0/9                      connected: T 7          a-full a-1000 10/100/1000BaseTX
^
 
My question is regarding the "T" in the status field. I can't find any documentation on this.

View 5 Replies View Related

Cisco Switching/Routing :: Will All 4-ports Of N5K Will Be Same Port-channel

Sep 12, 2012

Have 2 N2K with dual-connections to both 2 N5K, will all 4-ports of N5K will be the same port-channel. N2K as well ?

View 1 Replies View Related

Cisco Switching/Routing :: Configure 819 To Forward Ports For SQL And VNC?

Aug 15, 2012

I'm trying to forward ports for SQL and VNC using these commands in the CLI:
 
ip nat inside source static tcp 192.168.1.150 5900 interface GigabitEthernet0 5900
ip nat inside source static tcp 192.168.1.150 5800 interface GigabitEthernet0 5800
ip nat inside source static tcp 192.168.1.150 1433 interface GigabitEthernet0 1433
 
where 192.168.1.150 is my server (that hosts SQL server and that I want to be able to connect to remotely using VNC) and GigabitEthernet0 is my configured WAN interface.
 
When I try to connect from an external client I get the error:  "Failed to connect to server..." Is this a firewall issue?  How do I get round it?  The 819 is the only router/firewall in my network.

View 15 Replies View Related

Cisco Switching/Routing :: 3750X 1GB Ports Not Coming Up

Jan 22, 2013

I have hardcoded 1GB ports on 3750X to 1000 and full duplex for all servers connected. THe ports are not coming up with this speed and duplex settings. If I configure them to 100, I am able to see the port is up. Whereas if i connect the same servers to 2950 switches, i can see the ports working fine with 1000 speed ..we have tried with the latest universal IOS as well

View 7 Replies View Related

Cisco Switching/Routing :: First 12 Ports Of X6748 TX Are Not Working

Aug 19, 2012

I have a cisco 6509 switch in which i have 2 SUPs. I am using 3 Qty. of WS-X6748-GE-TX in the same switch. First 24 ports of module 1 and are not working. I replace the faulty moldule with the working one but now the new (good) module's first 12 ports stopped working. But when I insert the good card (the replaced one with the faulty) in other chassis it works fine.

View 2 Replies View Related

Cisco Switching/Routing :: SG300-10 - Special Ports 9&10?

Jun 6, 2012

I just purchased an SG300-10 (negular, non-POE) and planning on using it with no special configuratinos initially. Longer term, will be using VLAN and QOS for VOIP.What I would like to know is if ports 9 & 10 can be used as standard copper cat5e ports, or are they only useful for special purposes?  When I hookup my router/firewall to port 1 it all appears to work.  If I hook it up to 9 or 10, the port lights do not come on and it doesn't work.  I read that ports 9 & 10 don't have POE on the POE switch, but I assumed that all 10 ports would function with cat5e?

View 1 Replies View Related

Cisco Switching/Routing :: 4500 Ports Shows Only 0 Bit/Seg

May 20, 2012

I have installed a WS-X4448-GB-RJ45 on a 4503 chasis. I could not get input or output rate, just shows 0 bit/seg wether or not is forwarding traffic. I would like to know if I have to make any configuration or workaround. The IOS version is 12.2(37)SG1.

View 1 Replies View Related

Cisco Switching/Routing :: Ports In 4510 Not Working

Jul 10, 2012

This has been happening repeatedly time to time! we just replace the part! But now it has come to trouble us again.It happening only in one module like 6 to 10 ports wont work.

we run  IOS cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin will there be any bug in it?

View 10 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved