I came accross a Cisco 1801 router. As I understand it supposed to work with a dsl connection for internet access and configuration. I have cable internet access at home and since cisco routers are very versatile, I want to know if I can integrate this router into my home network, as a secondary router, and use it for its SSL vpn capabilities?
View 11 RepliesI have an FTP server that sits behind a cisco 1801 router.But now i want to add in FTP ports 21 and 20. I have added them in but i cant get it working via ftp.If i plug into the LAN and give my laptop an ip address on the same range as the server (192.168.2.100) then FTP works fine -
[code]...
I've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1.
The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.
Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0 disabled. In trying to get the switch to communicate with the router I made the following router config modifications.
FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27
I have two issues I want to resolve:
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.
open specific ports on 1941w Integrated Services Router.This specific router is a wireless VPN router that has a wired module and a wireless module and VPN so I'm getting 3 subnets on my network - 192.168.1.. for the wired connections, 10.100.1.... for wireless LAN connections and 10.100.2... for VPN remote connections.I know that by default all connected computers can access my Linux server data through telnet so the telnet port is open by default, the problem is that I have some other software licensing system on my Linux box that needs to be accessed through port 27000 and most of my users are using wireless connections and can't access that license because post 27000 is closed.what is the comand to open this post or any other port that I need to be open on the wired module, wireless module and VPN or at least poit me to somewhere where I can find all the commands that I can use for this router?
View 6 Replies View RelatedI would like test multicast routing with cisco1801.i create 2 Vlan. Vlan 200 (192.168.200.x) affect Fastethernet 1, Vlan 130 (192.168.130.x) Fastethernet 5.
Version IOS is : adipservice-k9 124-9.t1
ip multicast-routing
#int Vlan 130
ip address 192.168.130.254 255.255.255.0
Ip pim dense-mode
#int Vlan 200
Ip address 192.168.200.254 255.255.255.0
Ip pim dense-mode
I used VLC for my test.When i connect source (224.10.10.10) and recever ( Udp://@224.10.10.10:1234), that's ok!But, source is on the Vlan 200 and reicever on the Vlan 130, is not good!I test with "sparse-mode", i have same problem.
I have a client that that is installing a new network. They have requested the use of an CISCO891W-AGN-A-K9 mostly to be consistent with upgrades perfomed at other sites. I agree with the use of this router, so that's OK. The issue is that they have requested that I use the integrated PoE available on this model. I'm also OK with this as it will make a much neater installation. However, I can't seem to find much information on how to get the integrated PoE. I need clarification as to whether I can get a kit to upgrade this router. I generally purchase from sites like newegg or cdw (I'm an independent contractor) and I can't seem to find one with it. I have found some information on 800-IL-PM-4 and 800-ILPM-4 (who could confuse those ). Are they the same or different? Which one is the correct one and does it include the AC power adapter and can if be retro'ed into a router without the PoE?
View 2 Replies View RelatedI have 3850 switch with integrated WLC and i wonder if i can access the WLC via GUI ,also i need to know if it support Dynamic vlan assignment over SSID.
View 2 Replies View RelatedI have configured the following access-list on routers fa0 interface (i am using 1801)
access-list 111 permit ip any any log
and applied it in "in" direction on Fa0 interface.
Now when i am sending ssh packets to this interface its showing below
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
why its not showing any port number ?
I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
I am wondering what are the limits per routers for creating the vlans in vlan database? I have a 1801 router with the c180x-broadband-mz.151-3.T2 IOS and cant create more than 14 vlans.. How many does 2800 router support? Why I can't find this information anywhere on cisco.com?
View 7 Replies View RelatedI have a cisco 1801 (fixed), and want to use the fe0 WAN port to connect to the internet via a virgin media cable modem.
I am having a few issues (partly as I am new to cisco) and despite reading numerous posts both here and other sites, I am still stuck on how to setup the WAN side, I have read about virtual dial up & dialer interface.
I just picked up a 24 port Catalyst 2950 to expand my home network and learn a bit more about networking. Having just upgraded the IOS software 'm now trying to get this to work as required on my network but I'm having a few issues.
My intentions are to plug my cable router/modem wan connection which is set up as the dhcp server to fa 0/1, then use fa 0/2 - 24 for the rest of my wired network. So essentially all on the same subnet interfacing with the router 192.168.0.1.
So far I have set up all of the security on the switch, and have all switch ports assigned to vlan1 with no IPs. My laptop connected to fa0/2 however is not assigned an ip address. Looking at a few posts I ahve rightly or wrongly played about with dhcp snooping.
Config
Current configuration : 2205 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
service (code)
I remember I did that one time on 2800 router with Gi0/0 and Gi0/1 to connect another port channel in 3560G switch. I have no way to try it in ISR G2 router like 2900 or 3900 now. I know the the ethernet switch module must support it. I wonder if the integrated interfaces support it or not.
View 5 Replies View RelatedTrying to configure an 891-W on my home network.
Basic TW cable modem ---> 891-W with DHCP I have done the following and are getting an IP address but no internet. I have FE8 set as DHCP and VLAN1 as 192.168.1.1 255.255.255.0
I originally thought that "WAN GE 0" would be connected via my modem but I had no luck there either so I set FE8 as WAN?
Building configuration...
Current configuration : 2907 bytes
!
! No configuration change since last restart
version 15.1
[Code].....
What I am trying to do is port forward certain ports so the servers I'm trying to run will allow other people to connect.So far I got no where since I got a new ISP. They can't provide any assistance since I use a netgear router. One of their tech support said their modem has a built in router. The rest all said no. I noticed that the IP in CMD when I type ipconfig /all is 192.168.1.(15-47) it switches every now and then. But that is a local IP. Wouldn't that single that the modem is already routing the IP? When I put my router on it switches to 10.0.0.(2-55). These are all local IP's though. Does the modem have an integrated routing feature? Verizon really sucks so far. They can't answer their own questions without conflicting with each other.
The modem is getting the IP, and putting it into a local IP (What I believe is a routing feature) for the network. Now the local IP goes to the netgear wireless router, and gets routed again (Changed the local IP to 10.0.0.?). The netgear only got a Local IP the first time however, so the external IP is not being... worked with in the netgear router. It is trying to port forward for the local IP address, which already works for me obviously, however it is not a WAN IP address and therefore no one else is able to connect to any of my servers.And lastly, verizon states they have only "Modems" and "Wireless routers" so if they have no modems that doesn't come with this feature, then I need to learn how to port forward while the IP is being routed twice, similarly to when you have two routers hooked into each other.
I have a HP Pavilion dv6000 with windows xp. A couple of days ago the computer couldn't find any wireless connections. I've been into devmgmt.msc and looked, but I don't see any network card. In the folder Network Connections there are three alternatives, and none are wireless...I've tried to download the drivers for chipset, modem and network, but I still can't find anything.
View 1 Replies View RelatedI was wondering if I could use the CISCO3945 Integrated Gigabit Ethernet WAN ports for routing, I need to enable BGP and I was willing to use one of those ports.
View 2 Replies View RelatedWe had one 877W Cisco Soho Router ,I am planing to do a Site-Site VPN connection .while i configuring the router i am facing issue in assighning IP address in BVI interface .It gave me error "integrated routing and bridging is not configured bvi" .how can i resolve the issue .
View 1 Replies View RelatedI have integrated Intel 82577LM Gigabit Network Controller installed in my E6510.after installing updated driver from Intel and running hardware test it stopped working (displays "This device cannot start. (Code 10)" in driver details page).Also it says that device is 82577LC (it used to be 82577LM).
Intel hardware test displayed "EEPROM Failure" message. Looks like this test damaged network card firmware somehow.How do I restore/reset EEPROM of the network cad?i also tried deinstalling and reinstalling previous version of driver from Dell - no luck.
Is it possible to log onto a router over the internet using a pooled IP address? I want to be able to manage some routers that are in different sites, these are just providing internet access to clients. these are 1801 and 877s
View 4 Replies View RelatedI'm trying to set up an 1801 router with two WAN interfaces, fastethernet0 and fastethernet1. On the LAN side, I have two subnets. One subnet's internet traffic should be routed over fastethernet0, the other over fastethernet1.I've setup some route maps to accomplish this. I can surf the internet using subnet 192.168.2.0/24 fine, all traffic goes out of fastethernet0. However, and this is where the problem is, if I try to reach the internet using subnet 192.168.3.0/24, all packets go out interface fastethernet0 with the source address of fastethernet1!When I'm surfing the internet, from subnet 192.168.3.0/24, packets should be going out fastethernet1, now they're going out fastethernet0.
View 8 Replies View RelatedI'm having difficulty logging onto my 1801 router over the internet I can ping the device and tracert to it but I can't telnet or SSH ,Here is the config - Can you see whay this would happen. Its on ADSL link.
View 7 Replies View Relatedwe have cisco 1801 router and want to configure for PPPoE.As our ISP has provided adsl connection having following settings:
Encapsulation: PPPoE
Multiplexing: LLC based
VPI = 0
VCI = 103
Login =xxxxx
Password =xxxxx
IP: dynamically from ISP
configuring cisco router 1801 for above configuration.
when I'm trying to configure my router 1801 with PPPOE I have the message below "% PPPoE config from vpdn-group is converted to pppoe-profile based config.% Continue PPPoE configuration under 'bba-group pppoe global'.
View 3 Replies View RelatedI have a 1801 router connected to a 3550 switch with a regular 802.1q trunk, and I am curious as to what may be causing the unknown protocol drops on the connected router interface.
The switch is without any configuration at all except the following for the trunk configuration on the interface connecting to the router.
Switch:
-interface FastEthernet0/1
-switchport trunk encapsulation dot1q
-switchport mode trunk
Router:
-Interface FastEthernet8
-switchport mode trunk
There is nothing connected to the switch other than the router so the dropped traffic must be originating from the switch itself.The unknown protocol drop counter on the router increments by one every 30 seconds, and I tried using a packet sniffer but nothing noticeble showed up.
I read elsewhere on these forums that it might be udld, but that is not enabled by default, and just to be sure I tried disabling it on the interface and as expected it said it was not enabled, so I am ruling that one out.I also read that it could be because the router is recieving traffic from other protocols than IP, but I do not see how it applies in this case.
what does a 3550 send every 30 seconds that my 1801 does not understand?Could it have something to do with STP?
Have a customer who has two ISPs right now and only using one through a basic SOHO router. Looking to upgrade to something that supports dual WAN and allows connections from outside in on both WAN ports. There are 25-30 inside hosts.Requirements: Allow incoming connections on BOTH WAN ports to a single inside host
-This is a web app that needs as close to 100% uptime as possible
-Round robin DNS is set up
-Failover for internal people should one of the ISPs go down
Looking at either an ASA 5505 with Security Plus or an 891 Integrated Service Router.
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
I have a problem figuring out how to setup a home network connection running a VPN. I have been looking through the internet for answers and am still not sure how it all works.
View 9 Replies View RelatedI finally decided to get my own home lab so that I can configure to my hearts' content and not have to wait for access at the school to do it. I have three 2620 routers inter-connected with wic2t cards, and five 2950 switches. I have already set the config reg. on the routers to 0x2102 so that I can save my configs when I power down. When I pulled up the config regs on the switches, they all had 0xf as the reg number. Is this a good config reg number to have if I want to save the config before I power down?
Also, what would be a good ios version to have running on the switches and also the routers? I have access to other cisco IOS' but I want to double check. With this setup I would practice bgp, ppp, frame relay, rip2, ospf,eigrp, stp, pvst,pvst+, Rapid pvst+, rstp, and mstp.
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
View 1 Replies View RelatedHow to install a wireless network in home environment?
View 6 Replies View RelatedI am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
View 1 Replies View RelatedI have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies View Related