Cisco Switching/Routing :: 891W-AGN-A-K9 / How To Get Integrated PoE
Feb 26, 2012
I have a client that that is installing a new network. They have requested the use of an CISCO891W-AGN-A-K9 mostly to be consistent with upgrades perfomed at other sites. I agree with the use of this router, so that's OK. The issue is that they have requested that I use the integrated PoE available on this model. I'm also OK with this as it will make a much neater installation. However, I can't seem to find much information on how to get the integrated PoE. I need clarification as to whether I can get a kit to upgrade this router. I generally purchase from sites like newegg or cdw (I'm an independent contractor) and I can't seem to find one with it. I have found some information on 800-IL-PM-4 and 800-ILPM-4 (who could confuse those ). Are they the same or different? Which one is the correct one and does it include the AC power adapter and can if be retro'ed into a router without the PoE?
View 2 Replies
ADVERTISEMENT
Mar 22, 2012
I believe I have the steps done at the IOS to config the WAN port for SSH, but I still can't connect to it. I have "logging console 7" on so I am able to see that the router is dropping my TCP session requests. I figure this is just the built-in zone-based firewall at work.
Is there a very straightforward process, via the IOS, to allow SSH inbound on the WAN port? I'm not very familiar with the IOS other than basics so while I know how to do things like "transport input ssh" and "login local" and such on the vty 0 4 line, I have no idea whatsoever on what I should do with the firewall stuff. I believce the WAN interface is already a member of the outside zone though so I imagine one just has to somehow include ssh (preferably on a non-standard port) in the exceptions on the firewall somehow.
I have been poking around for a step-by-step IOS guide for this but only find info on configuring SSH itself but not how to open the firewall to allow the connection for it through.
View 11 Replies
View Related
Sep 24, 2012
I am trying to allow RDP through my 891w.I have tried a few different yjing to no avail. [code]
View 23 Replies
View Related
Feb 21, 2013
I have an 891w as my edge device for my home office. I have a VLAN for family use (wired and wireless) that routes out to the internet just fine. I have a second VLAN assigned to a VPN tunnel that backhauls traffic to my corporate network (wired and wireless) and all of the traffic gets to the corporate network fine when I am on that VLAN.
However, while I am on the VPN VLAN, no traffic gets to the internet. I believe it is because I have the gateway of last resort (0.0.0.0) set to the WAN IP address provided by my ISP, so DNS is resolving against corporate, but because there is no specific route, it is trying to dump the traffic back out the WAN without traversing the VPN tunnel.
View 4 Replies
View Related
Nov 6, 2011
I'm new to using Cisco Config Professional Express but a lot of things are just "off" with this utility. But my problem for this post is specifically the 891W's internal access point, or initial access to it.
My situation is that I have some 891W's. It's my first time working with them, as well as with CCP Express (2.5). After isolating the router and my PC to their own network, using the IP my PC got via DHCP frmo the router I opened a web broswer and connected to the router. The initiial configuration wizard came up and I went through the various screens. One of those screens had basic config info for the internal wireless AP which I provided. Somewhere in that screen it asked for a Hostname for the AP, and a password. It doesn't askfor a username though. To ensure I wouldn't run into confision, I made sure to set every password I ever get asked to configure as the same thing so the AP's password was also the same.
However after I finish with the wizard, the java-based CCP Express begins prompting me for first the main router credentials which I provide and it gets the router config, then it prompts mefor the username/password for the Access Point. First of all, the initial config wizard had never asked me for the username for the access point, only the hostname, and the password. I had assumed it was just going to use the main router username, or perhaps a blank username.
In any case, nothing I type ever works. I've used cisco/cisco, or a blank username with my new password, or the same username as the main router with the password ---- nothing. This is now the 4th time I have completely Reset the router to factory defaults and while I am learning the use of CCP Express through repetition, I'd also like to get this thing configured and out the door so my customer can use it.
View 3 Replies
View Related
Feb 9, 2012
I am trying to configure the FE8 (WAN port) to connect to the Internet. We're swtiching ISP'ssoon so this router was set up at my office and has since been deployed at the client site. So far it is just plugged in and powered, with a console cable attached but no LAN cabling since this router will replace an existing one using the same addressing (except the WAN settings of course). So for now I am just focused on working on the WAN side since I have the ISP's cable modem attached . I had intiially used CP Express to config the wan port with an IP and mask and the various port forwarding options I intend to use. Now, connected via console cable, I tried pinging the IP of the wan port, which works. Beyond that, can't ping anyting (8.8.8.8 - a Google IP), also can't resovle any DNS names which makes sense with no apparent connectivity. Likely my config is just imcomplete. Nowhere in sh run do I see a Default Gateway, yet this ISP did specify one so I assume I need to enter it. Not sure what's the right way - I get confusing results on searches telling me either to use ip default-gateway or ip default-network. I want to think that it's as simple as entering in the IP but so far I've learned with the IOS that you never do anythign without knowing all the possible implications, which I don't. Also while I am at it, I don't know what I should have for DNS entries. This router will not be a DNS server for any internal systems that function will be managed by the two Windows 2008 R2 DNS machines. The ISP has also provided two IP's for their DNS servers. I thought it would be a simple matter of just adding two entrires via ip name-server command, which I did. So now I have four entries, first the two internal servers (inaccessible currently due to no LAN cabing to this router), and the two ISP servers. Can't ping those either, but again there's no default gateway.
View 39 Replies
View Related
May 27, 2012
I'm working with some 891W's that have the internal 800-series AP. I have this router set up initially using Cisco Config Express, then, using Cisco Config Professional 2.5 I set up the firewall and other featuress that CCE doesn't do. Overall this is a very simple router, meant to be a small business Internet gateway device but is currently in my lab.
The intended WLAN setup is very simple. One SSID, with broadcast enabled, using WPA2-Personal. Auth: open Encryption is both TKIP and AES-CCM.
However no matter what I do I cannot get thhis thing to broadcast . In the past I had sometimes run into issues where if I had more than one AP running independently it would cause a channel conflict and one or both would cancel each other's radio, so I disabled all other AP's in my vicinity.
Also I've had issues in the past where f I enabled both TKIP and AES, sometimes clients can't find the AP as a result. My solution had been to disable one of them leaving just the other - no change here however.
Via the IOS, ssid config shows mbssid guest-mode which I believce is default.
Interestingly, if I do the following:
ap# Config t
ap(config)# dot11 ssid <myssid>
ap(config - ssid)#guest-mode
end
I end up with both "guest-mode" and "mbssid guest-mode" in the sh run for the AP, and voila, my AP broadcasts the SSID. However clients end up joining without any security at all, no prompts for pre-shared key or anything.
View 7 Replies
View Related
Jan 26, 2012
I have an 891W router that requires a firmware update to fix a bug wth the internal AP where all you get when accessing it via the CP Express ("Launch Wireless Application", which is just opening another web browser to your AP) is an Enter button. This issue seems to be common so I found a thread, though for the 881W (but same process) where the fix is to update the AP's firmware.
So I downloaded ap801-rcvk9w8-tar.124-21a.JY.tar from cisco.com, set it up in my tftp server, and at the console ran the following from the router:
Router#service-module wlan-ap 0 session <enter>
This brings me to the AP.
I then type in:
InternalAP#archive download-sw /force-reload /overwrite tftp://192.168.0.71/filename.tar <enter>
It seems to go through the process of re-imaging the fw but the end result now after it is done is that I cannot access the ap at all and the hostname has been screwed up. So now when I go to the AP (via Router#service-module wlan-ap 0 session <enter>), this is what I see:
AP6400.f177.d0ee>
If I type "enable", I get no username prompt but I do get a password prompt, however my pw no longer works. Also the IP address of the AP (192.168.0.2=) is no longe rpingable.
I did save the log of the console session for the (failed??) firmware upgrade process - the only odd thing I recall was that it seemed like it was trying to enter part of the update process commands but instead the router was interpreting them as a DNS lookup or something. Kind of stupid process it seems but anyway I am quite lost. Don't know what it'ssuch a challenge to update firmware.
View 9 Replies
View Related
Oct 12, 2012
I have had trouble to verify the support wireless speed and band that CISCO891W-AGN-A-K9 supports. I saw on a vendor website that it supports a max wireless transmission speed of 54Mbps but this seems low for what is supposed to be the current model wireless router which is supports 802.11n. What the maximum supported wireless speed and whether 5Ghz is supported? Plus I am thinking about purchasing it for my home wireless network (upgrading from an 871W).
View 1 Replies
View Related
Jan 6, 2013
I have an 891w that started acting up recently. Radio dot11 0 is reporting its a b radio. When it is actually an n 2.4 radio. Of course that radio is not allowing any clients to connect to it at this time. I have tried updating the firmware to the latest, tried a hardware reset but still a nogo.
sh interface output.
Dot11Radio0 is up, line protocol is down
Hardware is 802.11B Radio, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 11000 Kbit/sec, DLY 1000 usec,
[Code].....
View 6 Replies
View Related
Jun 1, 2013
I have 3850 switch with integrated WLC and i wonder if i can access the WLC via GUI ,also i need to know if it support Dynamic vlan assignment over SSID.
View 2 Replies
View Related
Mar 15, 2011
I have an 891W that I initially configured using CCP Express (2.5). So it has a WAN IP set, and through CCP Express I had enabled via the checkboxes the various default settings for security. This includes zone-based firewall. I then added a number of NAT entries in the setup wizard.
What never occured to me at the time was that I should have added entries that allow for remote access. So it seems I've locked myself out of accessing the router via the WAN interface even though I know it's IP. I'm sure it's just a matter of adding port exceptions for SSH and/or whatever port(s) CCP uses.
So I"m wondering what the proces woudl be. In the IOS while showing the running config., I see pages and pages of class-map stuff which at present I don't know enough about to risk editing anything directly. But maybe I don't have to? What would be the best way to, for example, enable SSH access through the firewall? I already have transport input ssh set on the interface itself so I believe it's ready to allow the connection, just that I can't get to it via WAN int. so I assume it's the firewall.
View 3 Replies
View Related
Dec 20, 2011
I remember I did that one time on 2800 router with Gi0/0 and Gi0/1 to connect another port channel in 3560G switch. I have no way to try it in ISR G2 router like 2900 or 3900 now. I know the the ethernet switch module must support it. I wonder if the integrated interfaces support it or not.
View 5 Replies
View Related
Jan 8, 2012
I came accross a Cisco 1801 router. As I understand it supposed to work with a dsl connection for internet access and configuration. I have cable internet access at home and since cisco routers are very versatile, I want to know if I can integrate this router into my home network, as a secondary router, and use it for its SSL vpn capabilities?
View 11 Replies
View Related
Apr 20, 2013
open specific ports on 1941w Integrated Services Router.This specific router is a wireless VPN router that has a wired module and a wireless module and VPN so I'm getting 3 subnets on my network - 192.168.1.. for the wired connections, 10.100.1.... for wireless LAN connections and 10.100.2... for VPN remote connections.I know that by default all connected computers can access my Linux server data through telnet so the telnet port is open by default, the problem is that I have some other software licensing system on my Linux box that needs to be accessed through port 27000 and most of my users are using wireless connections and can't access that license because post 27000 is closed.what is the comand to open this post or any other port that I need to be open on the wired module, wireless module and VPN or at least poit me to somewhere where I can find all the commands that I can use for this router?
View 6 Replies
View Related
Mar 12, 2011
What I am trying to do is port forward certain ports so the servers I'm trying to run will allow other people to connect.So far I got no where since I got a new ISP. They can't provide any assistance since I use a netgear router. One of their tech support said their modem has a built in router. The rest all said no. I noticed that the IP in CMD when I type ipconfig /all is 192.168.1.(15-47) it switches every now and then. But that is a local IP. Wouldn't that single that the modem is already routing the IP? When I put my router on it switches to 10.0.0.(2-55). These are all local IP's though. Does the modem have an integrated routing feature? Verizon really sucks so far. They can't answer their own questions without conflicting with each other.
The modem is getting the IP, and putting it into a local IP (What I believe is a routing feature) for the network. Now the local IP goes to the netgear wireless router, and gets routed again (Changed the local IP to 10.0.0.?). The netgear only got a Local IP the first time however, so the external IP is not being... worked with in the netgear router. It is trying to port forward for the local IP address, which already works for me obviously, however it is not a WAN IP address and therefore no one else is able to connect to any of my servers.And lastly, verizon states they have only "Modems" and "Wireless routers" so if they have no modems that doesn't come with this feature, then I need to learn how to port forward while the IP is being routed twice, similarly to when you have two routers hooked into each other.
View 4 Replies
View Related
Aug 11, 2011
I was wondering if I could use the CISCO3945 Integrated Gigabit Ethernet WAN ports for routing, I need to enable BGP and I was willing to use one of those ports.
View 2 Replies
View Related
May 28, 2012
We had one 877W Cisco Soho Router ,I am planing to do a Site-Site VPN connection .while i configuring the router i am facing issue in assighning IP address in BVI interface .It gave me error "integrated routing and bridging is not configured bvi" .how can i resolve the issue .
View 1 Replies
View Related
Feb 24, 2011
Alright, well I have a Cisco 891w router and have just about everything up and ready to deploy. I'm primarily using Cisco CP 2.4 to provision the router with minor tweaks being done in the CLI. I want to set up a filter to allow access to roughly 20 websites for the majority of my network which is all on the same VLAN. The ip ranges are x.x.x.10 - x.x.x.169 which I have set into a Network Object group called limitac. The second group ranges at x.x.x.170 - x.x.x.199 and is called allowac. I have set up DHCP bindings for all the devices that will connect to the network but I want to set up a web filter for only the first group. I cannot seem to find anything in the Cisco CP manual or the IOS manual for setting up filtering for a range of IPs only. Primarily there are a few computers that need full access to the web while the others should only have access to the sites I set up in the filter.
View 14 Replies
View Related
May 2, 2012
I am having problems connecting an 891w to a WLC, is it possible to have to separate vlans, one for the Lan ports and another for the AP module.
I do not want the AP part of the 891w in autonomous mode. The WAN port of the router will be connected to a DSL type service.
Is there a guide or something to get a 891W to connect to the WLC?
I would like to have users on a data vlan (vlan1) connecting to the network like a normal router, then the AP module to connect to the WLC via a different IP probably vlan 2
On the WLC itself i do not see any attempts in the logging.
View 10 Replies
View Related
Apr 18, 2012
What I currently have is a Cisco 891W Router as well as two ISP's (both with dynamic IP's) in. I'm currently just running one of my modems into the 891 through the FE8 port and then if for some reason I have an internet failure switching the ISP modems. What I'm wondering is if there is a fairly simple way to configure (and attach) both modems to this router and then set it up to handle this failover automatically?
View 1 Replies
View Related
Aug 31, 2011
I have an 891W with the internal AP. I want to update the AP's software but can't find anywhere to get it on Cisco's site. If I go to Download All, Routers, 800 series, 891W all I can choose is IOS, IOS ROMMON and upgrade to LWAPP. If I go to Wireless Wireless integrated service routers, 800 series, 891W I get IOS and IOS ROMMON.
View 1 Replies
View Related
Jun 21, 2012
i have a home lab network that is connected to my internet. I basically have a linksys router connected to cable modem and in order for my families internet to not go down while testing and learning my CCNA I am trying to treat the Linksys as the ISP.
1. Plugged my 891W router via FASTETHERNET 8 (192.168.1.10) into LAN Switch port 1 of my Linksys E4200 home router(192.168.1.1).
2. I plugged my 891W Gigabit 0 (10.10.10.1) LAN side into my 2950 Catalyst Switch (10.10.10.5 - VLAN 1)
3. my 2950 Catalyst switch (10.10.10.5 - Vlan 1) is plugged into my 2600 series router via the routers FE port (10.10.10.2).
There is a few more routers connected behind r2 but I am not dealing with them right now and there is also a switch connected into s1 but its not being used for this.
891w is labled r1
2950 is labled s1
2600 is labeled r2
I am running RIP Verison 2 for my network protocol.
r1 information below
----------------------------
r1#show ip protocols*** IP Routing is NSF aware ***
Routing Protocol is "rip" Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Sending updates every 30 seconds, next due in 24 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Redistributing: rip Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain GigabitEthernet0 2 2 Vlan4 2 2 wlan-ap0 2 2 Automatic network summarization is in effect Maximum path: 4 Routing for
[code].....
I can ping all over my homelab everything I can reach as long as I have a protocol up but I cannot reach the WAN IPs. I watched video by Jeremy Ciorara and I tried to follow the wan and nat part from a website [URL] And none of its working. I am not sure if this is a case where a private IP cannot function as a ISP and I am breaking some rule thats not mentioned in CCNA studies or if its something else. I tried these commands from Jeremy Video:
r1(config)#ip access-list standard "NAT_ADDRESSES"
r1(config-std-nacl)#permit any
r1(config)ip nat inside source list NAT_ADDRESSES interface fastEthernet 8 overload
However they did not work it was pretty close to whats in the basic website up there I listed as well. I think I went back to the basic configuration in the config file post above. Its really frustrating as I follow directions and they do not seem to work. I understand I am using my private 192.168.1.0 subnet as an ISP and maybe that has something to do with it but when yoru first learning and things dont work its kind of overwelming as you have problems seeing the big picture and dont yet trust in things you have learned as they are unfamiliar so its easy to get lost.
View 1 Replies
View Related
Nov 6, 2012
Over the weekend this router was put into production. SSHv2 is configfured and was working fine. Due to some circumstances, we had to avoid configuring any zone-pairs that included the self zone. This of course left the router open somewhat. SSH was secured but of course a few IP's from poorly regulated parts of the world spent the weekend trying to brute force log into the router. No luck it seems. Anyway, SSH continjued working, then we set up self zone-pairs (out to self and self to out). As ssh can't be Inspected, we did a pass log for each direction. This worked for a bit, then SSH just stopped working. I've seen this happen on 891W's in the lab here too, so is not something perhaps done by some unseen DoS attack or something.
View 8 Replies
View Related
Sep 22, 2010
Working with wired Cisco equipment for many years, but trying to configure an integrated wireless AP for the first time.
I have a Cisco 891w router with the following software (main and integrated AP801 wireless AP):
1. Cisco IOS Software, C890 Software (C890-UNIVERSALK9-M), Version 12.4(22)YB
License Level: advipservices
2. Cisco IOS Software, AP801 Software (AP801-RCVK9W8-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Opening a connection to integrated AP801 wireless device for performing wireless configuration tasks, the connection is established OK, authentication is passed OK using credentials from main configuration file, gaining level 15 privileges with enable command, but after that... no way to enter "Global Configuration mode" because there are no "configure" family commands present!!! Simply can't say "Conf t" because there is no such command!
View 9 Replies
View Related
Apr 8, 2013
Any issue creating a guest vlan to use the WIFI on an 891W router? The IOS is version 15.1. I have created discreet Vlan's and setup subinterfaces on both the WLAN_AP0 and GigaEthernet 0 interfaces with dot1q encapsulation. The client will receive an IP from the pool but cannot ping or connect beyond the default gateway.
The external interface is using Nat overload and all wired clients are successful in connecting to outside addresses. I have insert a permit any statement in the acl which affects the external port but still no success.
View 7 Replies
View Related
Sep 2, 2012
I can't get the internal 3G modem on my HP2510p with Windows 7 Professional 32 bit working. So far I've downloaded and installed the following:-
HP Broadand Wireless Modules - Sierra Wireless Inc
HP Connection Manager - Hewlett Packard
HP Wireless Assistant - Hewlett Packard
Qualcomm Gobi Driver Package for HP - QUALCOMM
but it's still saying 'no dial tone' and not reading that it has a 3G modem. If I've downloaded anything, how I can uninstall it.
View 1 Replies
View Related
May 21, 2013
How to upgrade the IOS of the Integrated wireless AP in a Cisco 881W using TFTP server (I do have software)Router side is not an issue it is the integrated AP that gives problem?
View 14 Replies
View Related
Oct 1, 2012
I was doing some research on the Cisco ASR1001 model Router and within the description on the official Cisco page it mentions having various models that come with an "Integrated Daughter Card" or "IDC". I was curious as to what the IDC is exactly, considering there is an ASR1001 model without it.
View 2 Replies
View Related
Jun 2, 2013
I am currently deploying Cisco ASR9K BNG solution and it needs to be integrated with a Cisco ACS 3.3 (yes that old .. going to migrate to new product in the future) equipment. There are several specific attributes need that are not on the base config of the ACS 3.3 but it seems that i can configure them manually:In addition to supporting a set of predefined RADIUS vendors and vendor-specific attributes (VSAs), Cisco Secure ACS supports RADIUS vendors and VSAs that you define. Vendors you add must be IETF-compliant; therefore, all VSAs that you add must be sub-attributes of IETF RADIUS attribute number 26..This is from the ACS 3.3 configuration manual.I have never done this user defined VSAs.
View 1 Replies
View Related
Mar 28, 2011
I have two desktop PCs connected via PRO/100VE LAN and am about to replace one of these with a desktop that has Integrated 10/100/1000Base-T. Will the two machines be able to communicate? One machine will use XP Home and the new machine Windows 7.
View 2 Replies
View Related
Apr 10, 2009
Bought a Vostro 220S about 2 months ago. After about three weeks, while I'm using it, the integrated NIC dies. All of a sudden I get the "Network Cable Disconnected" pop-up. No LEDs lit by the network jack. Contact Dell support who decides it's the motherboard.Three days later, the exact same failure. Contact support again. This time they want me to re-install Windows (yeah...right). I refused since the motherboard fixed it the first time. They finally agree to replace the motherboard again. Using the same router and cable that worked for years with my old computer. After the first failure, I switched ports on the router. While waiting for the motherboard replacements, I had installed an old PCI NIC I had laying around. Worked fine...still is. I'm not about to re-install Windows, which is what I know they'll want. I'll stick with the PCI card. Both of the people at Dell support as well as the tech they sent out told me they've not seen this before.
View 6 Replies
View Related
Jul 19, 2012
there was a very close lightning strike near my house and my DELL XPS 210 accessed the router before but not after. Noother elctronics, even my 2 other DELL computers were affected. I've eliminated the NIC cables, router port, everything but the actual NIC card. But diagnostics say it's working properly. Could a registry entry have been corrupted (I have a registry backup the day before). Can I replace the Integrated NIC with an internal (or external) NIC? I'm running XP Professional SP3.
View 3 Replies
View Related
