Cisco Switching/Routing :: 891W Wireless Radio Showing As 802.11b And Inop
Jan 6, 2013
I have an 891w that started acting up recently. Radio dot11 0 is reporting its a b radio. When it is actually an n 2.4 radio. Of course that radio is not allowing any clients to connect to it at this time. I have tried updating the firmware to the latest, tried a hardware reset but still a nogo.
sh interface output.
Dot11Radio0 is up, line protocol is down
Hardware is 802.11B Radio, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 11000 Kbit/sec, DLY 1000 usec,
[Code].....
View 6 Replies
ADVERTISEMENT
Oct 12, 2012
I have had trouble to verify the support wireless speed and band that CISCO891W-AGN-A-K9 supports. I saw on a vendor website that it supports a max wireless transmission speed of 54Mbps but this seems low for what is supposed to be the current model wireless router which is supports 802.11n. What the maximum supported wireless speed and whether 5Ghz is supported? Plus I am thinking about purchasing it for my home wireless network (upgrading from an 871W).
View 1 Replies
View Related
Feb 26, 2012
I have a client that that is installing a new network. They have requested the use of an CISCO891W-AGN-A-K9 mostly to be consistent with upgrades perfomed at other sites. I agree with the use of this router, so that's OK. The issue is that they have requested that I use the integrated PoE available on this model. I'm also OK with this as it will make a much neater installation. However, I can't seem to find much information on how to get the integrated PoE. I need clarification as to whether I can get a kit to upgrade this router. I generally purchase from sites like newegg or cdw (I'm an independent contractor) and I can't seem to find one with it. I have found some information on 800-IL-PM-4 and 800-ILPM-4 (who could confuse those ). Are they the same or different? Which one is the correct one and does it include the AC power adapter and can if be retro'ed into a router without the PoE?
View 2 Replies
View Related
Mar 22, 2012
I believe I have the steps done at the IOS to config the WAN port for SSH, but I still can't connect to it. I have "logging console 7" on so I am able to see that the router is dropping my TCP session requests. I figure this is just the built-in zone-based firewall at work.
Is there a very straightforward process, via the IOS, to allow SSH inbound on the WAN port? I'm not very familiar with the IOS other than basics so while I know how to do things like "transport input ssh" and "login local" and such on the vty 0 4 line, I have no idea whatsoever on what I should do with the firewall stuff. I believce the WAN interface is already a member of the outside zone though so I imagine one just has to somehow include ssh (preferably on a non-standard port) in the exceptions on the firewall somehow.
I have been poking around for a step-by-step IOS guide for this but only find info on configuring SSH itself but not how to open the firewall to allow the connection for it through.
View 11 Replies
View Related
Sep 24, 2012
I am trying to allow RDP through my 891w.I have tried a few different yjing to no avail. [code]
View 23 Replies
View Related
Feb 21, 2013
I have an 891w as my edge device for my home office. I have a VLAN for family use (wired and wireless) that routes out to the internet just fine. I have a second VLAN assigned to a VPN tunnel that backhauls traffic to my corporate network (wired and wireless) and all of the traffic gets to the corporate network fine when I am on that VLAN.
However, while I am on the VPN VLAN, no traffic gets to the internet. I believe it is because I have the gateway of last resort (0.0.0.0) set to the WAN IP address provided by my ISP, so DNS is resolving against corporate, but because there is no specific route, it is trying to dump the traffic back out the WAN without traversing the VPN tunnel.
View 4 Replies
View Related
Nov 6, 2011
I'm new to using Cisco Config Professional Express but a lot of things are just "off" with this utility. But my problem for this post is specifically the 891W's internal access point, or initial access to it.
My situation is that I have some 891W's. It's my first time working with them, as well as with CCP Express (2.5). After isolating the router and my PC to their own network, using the IP my PC got via DHCP frmo the router I opened a web broswer and connected to the router. The initiial configuration wizard came up and I went through the various screens. One of those screens had basic config info for the internal wireless AP which I provided. Somewhere in that screen it asked for a Hostname for the AP, and a password. It doesn't askfor a username though. To ensure I wouldn't run into confision, I made sure to set every password I ever get asked to configure as the same thing so the AP's password was also the same.
However after I finish with the wizard, the java-based CCP Express begins prompting me for first the main router credentials which I provide and it gets the router config, then it prompts mefor the username/password for the Access Point. First of all, the initial config wizard had never asked me for the username for the access point, only the hostname, and the password. I had assumed it was just going to use the main router username, or perhaps a blank username.
In any case, nothing I type ever works. I've used cisco/cisco, or a blank username with my new password, or the same username as the main router with the password ---- nothing. This is now the 4th time I have completely Reset the router to factory defaults and while I am learning the use of CCP Express through repetition, I'd also like to get this thing configured and out the door so my customer can use it.
View 3 Replies
View Related
Feb 9, 2012
I am trying to configure the FE8 (WAN port) to connect to the Internet. We're swtiching ISP'ssoon so this router was set up at my office and has since been deployed at the client site. So far it is just plugged in and powered, with a console cable attached but no LAN cabling since this router will replace an existing one using the same addressing (except the WAN settings of course). So for now I am just focused on working on the WAN side since I have the ISP's cable modem attached . I had intiially used CP Express to config the wan port with an IP and mask and the various port forwarding options I intend to use. Now, connected via console cable, I tried pinging the IP of the wan port, which works. Beyond that, can't ping anyting (8.8.8.8 - a Google IP), also can't resovle any DNS names which makes sense with no apparent connectivity. Likely my config is just imcomplete. Nowhere in sh run do I see a Default Gateway, yet this ISP did specify one so I assume I need to enter it. Not sure what's the right way - I get confusing results on searches telling me either to use ip default-gateway or ip default-network. I want to think that it's as simple as entering in the IP but so far I've learned with the IOS that you never do anythign without knowing all the possible implications, which I don't. Also while I am at it, I don't know what I should have for DNS entries. This router will not be a DNS server for any internal systems that function will be managed by the two Windows 2008 R2 DNS machines. The ISP has also provided two IP's for their DNS servers. I thought it would be a simple matter of just adding two entrires via ip name-server command, which I did. So now I have four entries, first the two internal servers (inaccessible currently due to no LAN cabing to this router), and the two ISP servers. Can't ping those either, but again there's no default gateway.
View 39 Replies
View Related
May 27, 2012
I'm working with some 891W's that have the internal 800-series AP. I have this router set up initially using Cisco Config Express, then, using Cisco Config Professional 2.5 I set up the firewall and other featuress that CCE doesn't do. Overall this is a very simple router, meant to be a small business Internet gateway device but is currently in my lab.
The intended WLAN setup is very simple. One SSID, with broadcast enabled, using WPA2-Personal. Auth: open Encryption is both TKIP and AES-CCM.
However no matter what I do I cannot get thhis thing to broadcast . In the past I had sometimes run into issues where if I had more than one AP running independently it would cause a channel conflict and one or both would cancel each other's radio, so I disabled all other AP's in my vicinity.
Also I've had issues in the past where f I enabled both TKIP and AES, sometimes clients can't find the AP as a result. My solution had been to disable one of them leaving just the other - no change here however.
Via the IOS, ssid config shows mbssid guest-mode which I believce is default.
Interestingly, if I do the following:
ap# Config t
ap(config)# dot11 ssid <myssid>
ap(config - ssid)#guest-mode
end
I end up with both "guest-mode" and "mbssid guest-mode" in the sh run for the AP, and voila, my AP broadcasts the SSID. However clients end up joining without any security at all, no prompts for pre-shared key or anything.
View 7 Replies
View Related
Jan 26, 2012
I have an 891W router that requires a firmware update to fix a bug wth the internal AP where all you get when accessing it via the CP Express ("Launch Wireless Application", which is just opening another web browser to your AP) is an Enter button. This issue seems to be common so I found a thread, though for the 881W (but same process) where the fix is to update the AP's firmware.
So I downloaded ap801-rcvk9w8-tar.124-21a.JY.tar from cisco.com, set it up in my tftp server, and at the console ran the following from the router:
Router#service-module wlan-ap 0 session <enter>
This brings me to the AP.
I then type in:
InternalAP#archive download-sw /force-reload /overwrite tftp://192.168.0.71/filename.tar <enter>
It seems to go through the process of re-imaging the fw but the end result now after it is done is that I cannot access the ap at all and the hostname has been screwed up. So now when I go to the AP (via Router#service-module wlan-ap 0 session <enter>), this is what I see:
AP6400.f177.d0ee>
If I type "enable", I get no username prompt but I do get a password prompt, however my pw no longer works. Also the IP address of the AP (192.168.0.2=) is no longe rpingable.
I did save the log of the console session for the (failed??) firmware upgrade process - the only odd thing I recall was that it seemed like it was trying to enter part of the update process commands but instead the router was interpreting them as a DNS lookup or something. Kind of stupid process it seems but anyway I am quite lost. Don't know what it'ssuch a challenge to update firmware.
View 9 Replies
View Related
Mar 15, 2011
I have an 891W that I initially configured using CCP Express (2.5). So it has a WAN IP set, and through CCP Express I had enabled via the checkboxes the various default settings for security. This includes zone-based firewall. I then added a number of NAT entries in the setup wizard.
What never occured to me at the time was that I should have added entries that allow for remote access. So it seems I've locked myself out of accessing the router via the WAN interface even though I know it's IP. I'm sure it's just a matter of adding port exceptions for SSH and/or whatever port(s) CCP uses.
So I"m wondering what the proces woudl be. In the IOS while showing the running config., I see pages and pages of class-map stuff which at present I don't know enough about to risk editing anything directly. But maybe I don't have to? What would be the best way to, for example, enable SSH access through the firewall? I already have transport input ssh set on the interface itself so I believe it's ready to allow the connection, just that I can't get to it via WAN int. so I assume it's the firewall.
View 3 Replies
View Related
Nov 21, 2011
I hav e a 3750X Cisco Switch (WS-C3750X-48T-S) It is two Ethernet base SFP installed and working fine at slot 1 & 2, Now i am trying to install GLC-SX-MM in 3rd and 4th slot, but its not coming up, showing not present?
Gi1/1/1 connected trunk a-full a-1000 10/100/1000BaseTX SFP
Gi1/1/2 connected trunk a-full a-1000 10/100/1000BaseTX SFP
Gi1/1/3 notconnect 1000 auto auto Not Present
Gi1/1/4 notconnect 1 auto auto Not Present
image i am using is
C3750E-UNIVERSALK9-M
View 6 Replies
View Related
Apr 14, 2012
For an assignment in a class I am taking I created a simple network using GNS3 and set up static routing. Everything works fine, I can ping all of the hosts. One of the questions I am supposed to fill out is what happens when I use the "show ip route" and "show ip protocols" commands. When I use "show ip route" I get what seems to be the correct output. However when I use the "show ip protocols" command nothing happens. No output, no error, no nothing. It just goes right back to the prompt. This happens exactly the same on both routers in my network. incase it matters the router is c3640.
PS. would the output be non-existent because I have not set up any ip protocols. In a similar assignment I set up rip and when I used "show ip protocols" i did get what appeared to be the correct output. However I didn't write it down and when I put in the command again about an hour later after I took a break I also did not get an output until I re-entered the rip related commands.
View 2 Replies
View Related
Dec 4, 2011
We ordered the wrong part number for a Cisco 4506 non-E chassis, the part number is: WS-X4624-SFP-E and the device is showing "Unsupported module"; What would the part number be for the non-E? WS-X4448-GB-SFP,Catalyst 4500 48-Port 1000Base-X (SFPs Optional) ?
View 1 Replies
View Related
Apr 8, 2013
we have 6500 cisco switch as a backbone switch in universty. When ı want to look mac addres table , it does no show all mac address.ı mean if ı type ;show mac address-table there are not all mac address.
View 3 Replies
View Related
May 12, 2012
I have configured the following access-list on routers fa0 interface (i am using 1801)
access-list 111 permit ip any any log
and applied it in "in" direction on Fa0 interface.
Now when i am sending ssh packets to this interface its showing below
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
why its not showing any port number ?
View 1 Replies
View Related
Nov 18, 2012
I am runing 802.1x and MAB authentication of devices connected to a 3560 switch (in test). When I run 'terminal monitor' I am getting alot of authentication fail-msg. Is it possible to get the switch not to show them? I have to do some debugging on SNMP and DHCP to be able to figure out why I get these msg, but since the switch is blasting out so many auth-msg it is hard to see the debug messages. [code]
View 3 Replies
View Related
Jun 14, 2012
Looking at the following output (show interface status) from one of our 4507s I see gig interfaces 3/2 to 3/6 are all trunked (dot1q). When I look at a show run they do not show as trunked. They should indicate switchport trunk encapsulation dot1q and switchport mode trunk (as does interface gig4/2). I have seven other 4507s all running the same IOS: 12.2(25)EWA8 and they all show the same information in show run and show interface status (as far as trunked goes). This is not a problem as I know the interfaces are trunked and working properly I am just puzzled as to why I see this difference.
Here is the sho int gig3/2 trunk. It looks like you are correct. I did not realize some were set to trunk mode on and others were not. I would think the running config would still show the port using dot1q but I guess not.
View 3 Replies
View Related
Aug 16, 2012
when I do a show module in my cat 6509, the standby sup is saying unknown, it has the same IOS as the primary card.
what does this mean? are there any tests I can run on the card?
View 2 Replies
View Related
Jun 30, 2008
Cisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
View 2 Replies
View Related
Jan 27, 2013
We have several stacks of 3750 switches where this problem is occurring. All of the switches are running IOS version 12.2(50)SE3. (Yes, I know it's old.)
We're seeing inconsistency in how the stack reports members when issuing the following commands:
sow switch
show version
show inventory
Not all members are showing up in the output of the "show version" and "show inventory" commands. For example:
HUNTI-WV-WDAC03#sh switch
H/W Current
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
1 Member 108c.cff2.ea00 15 0 Ready
2 Member 8cb6.4f0a.a600 1 0 Ready
*3 Master 8cb6.4f0a.9c00 1 0 Ready
(all three switches in stack are displayed)(code)
View 1 Replies
View Related
Mar 9, 2013
I have couple of SFP and most of them are working fine except this:-
Nexus7000# show interface ethernet 6/31 transceiver details
[code]...
a) What is the reason this is not getting recognized?
b) Is theSFP SFBR-5766PZ-CS1 plug and play in the 7000 Nexus?
View 7 Replies
View Related
Feb 4, 2010
We have a C4500 with 2 sup V which is showing high CPU values sometimes.When this occures, the switch shows 95-100% for total cpu for a few hours at a time.show proccesses cpu shows process Cat4k Mgmt LoPri with an unusual cpu value of 65% The show platform heath command gave me a high reading for K2FibFC DelFlow which is about 50% at this peak but is normaly around 1%?
what the process K2FibFC DelFlow means and what could be the cause of this peak?
View 12 Replies
View Related
Jan 22, 2013
We have 3 Cat 4500 switches on three floors teh 3rd floor switch connects to the 2nd and 4th floor switches ,but we are receiving an alert from monitoring tool that " Interface(314) Backup-1Gb-Ring is Down at least 2 min on Switch: SOM500-4510-3FL the following output from "sh int status module 1 " shows the int 1/3 and 1/4 are 'inactive'local IT guy said If the status is inactive,the ports cannot be used and might lost the capability when he added 48-port blade into the 10th slot.
2nd Floor
Port Name Status Vlan Duplex Speed TypeTe1/1 SOM500-Core1 connected trunk full 10G 10GBase-LRMTe1/2 SOM500-Core1 connected trunk full 10G 10GBase-LRMGi1/3 Backup-1Gb-Ring notconnect 1 full 1000 1000BaseSXGi1/4 Backup-1Gb-Ring connected trunk full 1000 1000BaseSX
3rd FloorPort Name Status Vlan Duplex Speed TypeTe1/1 SOM500-Core1 connected trunk full 10G 10GBase-LRMTe1/2 SOM500-Core1 connected trunk full 10G 10GBase-LRMGi1/3 Backup-1Gb-Ring inactive 1 full 1000 1000BaseSXGi1/4 Backup-1Gb-Ring inactive 1 full 1000
[code]....
View 6 Replies
View Related
Apr 23, 2012
I always though that sh mac address table dynamic interface xx/xx/xx was a subset of "sh mac address table" 6590 Version 12.2(33)SXI I have two mac addresses on downstream switches that will only show up when using
sh mac address-table dynamic interface Te4/10
* 903 0050.77a9.6e3c dynamic Yes 0 Te4/10
* 903 0050.77a9.5766 dynamic Yes 0 Te4/10
when using "old faithful"
sh mac address-table | inc 6e3c
*nothing*
or
sh mac address-table dynamic | inc 6e3c
*nothing*
nothing shows up?this vlan has no layer three interfaces
View 1 Replies
View Related
Apr 14, 2013
I have installed a Catalyst 2960-S and a 3750-X-12S and I am trying to setup a VLAN 51 for some VoIP phones. I have added the VLAN as an interface on both switches, but the 3750 is not showing VLAN 51 as active when i do a show vlan. Also, it omitts showing Gi1/0/1 & Gi1/0/3 which are uplinks to 2960-S switches plugged in and working on VLAN1.
Catalyst3750SFP#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/0/2, Gi1/0/4, Gi1/0/5
[Code].....
View 2 Replies
View Related
Aug 8, 2012
We are facing issue of getting very high CPU utilization for the VSS Switch model WS-C6509-E some times approx 100%.Attaching here show tech-support taken later after CPU normal along with show logging, show cpu sorted.HCAINNOI01XXXCS0001#sh proces cpu | ex 0.0%CPU utilization for five seconds: 100%/13%; one minute: 90%; five minutes: 91%PID 5Sec 1Min 5Min Process16406 91.2% 75.2% 76.2% ios-base16426 1.7% 1.4% 1.4% udp.proc16429 0.3% 0.3% 0.3% raw_ip.proc16432 2.8% 3.1% 3.1% cdp2.iosproc
View 3 Replies
View Related
Mar 6, 2012
We have supplied Cisco Swtch 2960 with gig SFP modules. It is working fine. However, when I do a show inventory it show proper part no. for the switch chassis but for the GLC T module it shows as unspecified in the PID column.
View 1 Replies
View Related
Oct 26, 2011
I just upgraded my power supply's from 2500Watts to 4000watts, however the show power still shows 2500watts.how do i make the 6513 recongize the change? I do have 250volts at 30 amps connected to each power supply.
system power redundancy mode = redundant
system power total = 2331.00 Watts (55.50 Amps @ 42V)
system power used = 1741.74 Watts (41.47 Amps @ 42V)
system power available = 589.26 Watts (14.03 Amps @ 42V)
[code]...
View 1 Replies
View Related
Mar 5, 2013
We have a stack setup with 2 C3750x-12s and 5 C3750x-48p switches. We have two of these stacks. One is working and responding with snmp just fine. Our second one is showing the errors in the logThe only difference i see between the two stacks right now are the sw versions.
View 1 Replies
View Related
Nov 5, 2012
I have having two Cisco 6509 both working are my main Core Switches with which I have all my Layer 2 VLANs configured and then distributed thru the trunks links to all the Access Switches. I have L3- Vlans also configured on them with which one switch in primary and the other is secondary. All of sudden last night I got this message on my core switch 2 this for VLAN 1 which is my users LAN, how can I check as to what would have caused the core switch 2 HSRP to be active and then in standby
*Nov 5 23:33:29.296: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Standby -> Active
*Nov 5 23:33:29.796: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Standby -> Active
*Nov 5 23:33:29.804: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Active -> Speak
*Nov 5 23:33:29.920: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Active -> Speak
*Nov 5 23:33:40.144: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Speak -> Standby
*Nov 5 23:33:41.280: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Speak -> Standby
Also last night i got call from office saying that we are getting huge delay in pinging the default gateway of the user LAN which is the same vlan as the above and it was just for few minutes and then it was back to normal and now when I came to office and check there were no logs in both the core switches. When I checked the cpu utlization it was showing me high on both the switches how can I check as to what would have caused the CPU utilisation to go high all of suddedn?
INPMHCORS01#$ sh processes cpu his
11111 11111 11111 1111111111
8885555588888666669999922222666665555511111777773333300000
100
90
80
[code]....
View 1 Replies
View Related
Jun 12, 2013
I have reconfigured the FEX numbers attached to a Nexus 5548 running on NXOS5.2 If I do show running-config the interfaces are not there anymore. But if I do show startup-config the old Fex interfaces still shows up. I did try write erase then saved the running-config and its still there.
View 1 Replies
View Related
May 10, 2013
In our company 3nos Cisco 3750 (WS-C3750-48P) access switch in stake mode. All port are assigned with voice and data Vlan also Avaya IP connected with this switches. From last few days tow port 2/0/7 and 2/0/8 is showing amber and status is showing err-disable. At Avaya end it is showing a message “ETHERNET WAITING” in phone dispaly. I try to connect laptop directly with these ports but it is showing "Cross Connectivity". [code]
View 4 Replies
View Related
