Cisco Switching/Routing :: 4500 Is Showing High CPU Values
Feb 4, 2010
We have a C4500 with 2 sup V which is showing high CPU values sometimes.When this occures, the switch shows 95-100% for total cpu for a few hours at a time.show proccesses cpu shows process Cat4k Mgmt LoPri with an unusual cpu value of 65% The show platform heath command gave me a high reading for K2FibFC DelFlow which is about 50% at this peak but is normaly around 1%?
what the process K2FibFC DelFlow means and what could be the cause of this peak?
View 12 Replies
ADVERTISEMENT
Oct 14, 2012
We have a 4500 series switch that is running around 39% cpu utilization but seems to be dragging a bit. I did a show platform health and GalChassisVp-review has a target of 3% but an actual of 17%. All other actual values were at or below target values. I then went to show platform cpu packet statistics and in the "Packets received by Packet Queue" all queue packet values at 5 sec, 1 min, 5 min and 1 hour avg were either 0 or 1 with the exception of Esmp - that averaged 351/377/317 and 313 respectively. I then checked show platform hardware acl input entries static and the entry type InputEsmpToCPU had a whopping 10121370 hit count. All other entry types were well under that number.
View 2 Replies
View Related
Sep 7, 2012
My 4500 core always in 60 % cpu utility , and when i run #sh proc cpu sorted i find that
55 29725041543795572214 0 39.43% 41.40% 41.39% 0 Cat4k Mgmt LoPri
Which mean that this process is the top one , and when i run #sh platform health i found that Stub-JobEventSchedul
10.00 15.98 10 64 100 500 20 17 12 29269:55 K2 CpuMan Review
30.00 35.60 30 48 100 500 49 46 32 52390:52
Those two process are the top and they already exceed their maximum rang and when i run #sh platform cpu packet statistics i can find that Packets Received by Packet Queue
Queue Total 5 sec avg 1 min avg 5 min avg 1 hour avg
---------------------- --------------- --------- --------- --------- ----------
Esmp 5053121950 475 462 340 326
L2/L3Control 244395185 17 8 5 11
Host Learning 67315739 0 0 0 0
L3 Fwd Low 346689615 73 23 14 13
L2 Fwd Low 5336180603 1180 1129 831 804
L3 Rx Low 2287913 0 0 0 0
RPF Failure 7510829 1 0 0 0
View 2 Replies
View Related
Feb 6, 2013
We have a Switch Catalyst 4500, model WS-C4510R+E, with 2 Supervisors, models V-10GE, which is showing high CPU values all times.When this occures, the switch shows 95-100% for total cpu for a few hours at a time.show proccesses cpu shows process Cat4k Mgmt LoPri with an unusual cpu value of 56% The show platform heath command gave me a high reading for K2L2 Address Table R which is curently 9,45% but the last hour is around a 20% average CPU ?[URL] what the process K2L2 Address Table R means and what could be the cause of this peak?
View 3 Replies
View Related
May 8, 2011
My Catalayst 4507 is reaching up to 82% CPU utilization and I noticed that K2L2 Address Table R is causing the high CPU.
C4507#sh processes cpu | in HiPri|LoPri|CPU utilizationCPU utilization for five seconds: 82%/1%; one minute: 86%; five minutes: 87% 54 350533923 329104616 1065 13.27% 13.84% 13.86% 0 Cat4k Mgmt HiPri 55 1771768520 274992685 6442 59.91% 64.55% 66.04% 0 Cat4k Mgmt LoPri
C4507#sh platform health | in K2L2|%CPuK2L2 Address Table R 2.00 66.35 12 5 100 500 91 82 58 27272:55K2L2 New Static Addr 2.00 0.00 10 0 100 500 0 0 0 0:00K2L2 New Multicast A 2.00 0.00 10 5 100 500 0 0 0 0:18K2L2 Dynamic Address 2.00 0.00 10 5 100 500 0 0 0 0:16K2L2 Vlan Table Revi 2.00 0.00 12 8 100 500 0 0 0 1:22
View 2 Replies
View Related
Aug 8, 2012
We are facing issue of getting very high CPU utilization for the VSS Switch model WS-C6509-E some times approx 100%.Attaching here show tech-support taken later after CPU normal along with show logging, show cpu sorted.HCAINNOI01XXXCS0001#sh proces cpu | ex 0.0%CPU utilization for five seconds: 100%/13%; one minute: 90%; five minutes: 91%PID 5Sec 1Min 5Min Process16406 91.2% 75.2% 76.2% ios-base16426 1.7% 1.4% 1.4% udp.proc16429 0.3% 0.3% 0.3% raw_ip.proc16432 2.8% 3.1% 3.1% cdp2.iosproc
View 3 Replies
View Related
Nov 5, 2012
I have having two Cisco 6509 both working are my main Core Switches with which I have all my Layer 2 VLANs configured and then distributed thru the trunks links to all the Access Switches. I have L3- Vlans also configured on them with which one switch in primary and the other is secondary. All of sudden last night I got this message on my core switch 2 this for VLAN 1 which is my users LAN, how can I check as to what would have caused the core switch 2 HSRP to be active and then in standby
*Nov 5 23:33:29.296: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Standby -> Active
*Nov 5 23:33:29.796: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Standby -> Active
*Nov 5 23:33:29.804: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Active -> Speak
*Nov 5 23:33:29.920: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Active -> Speak
*Nov 5 23:33:40.144: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Speak -> Standby
*Nov 5 23:33:41.280: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Speak -> Standby
Also last night i got call from office saying that we are getting huge delay in pinging the default gateway of the user LAN which is the same vlan as the above and it was just for few minutes and then it was back to normal and now when I came to office and check there were no logs in both the core switches. When I checked the cpu utlization it was showing me high on both the switches how can I check as to what would have caused the CPU utilisation to go high all of suddedn?
INPMHCORS01#$ sh processes cpu his
11111 11111 11111 1111111111
8885555588888666669999922222666665555511111777773333300000
100
90
80
[code]....
View 1 Replies
View Related
Sep 1, 2011
my cisco 2611 series router is showing garbage value at start up and not allowing me to enter in Romon mode I check the bitrate in console .it is 9600/8N till then i am unable to start the router Can you tell me how to change configuration register value without entering in rommon mode
View 6 Replies
View Related
Oct 17, 2011
I have a WLC 2106 with 3 APs. Everything works and users can connect, but the throughput seem to be lower than it should (it is around 8Mbps and should be around 30-50Mbps). And all speed and duplex has been accounted for.
I am trying to understand the stats that I see for the 802.11 MAC counters I under the Wireless APs.on the controller.
That screenshot is attached. I see high numbers for the following areas:
- Tx Failed Count
- RTS Failure Count
- FCS Error Count
what these mean and what could cause this? Maybe these are normal and not a concern.
View 1 Replies
View Related
Apr 16, 2012
I have a WS- C2924C-XL switch that I would like to upgrade the IOS version on. The IOS version in question can only be installled on an 8MB version of this switch, I have tried to confirm the amount of memory present in the device but I am getting conflicting values depending on where I look.The model number would indicate that this device is a 4MB version, therefore not compatable with the upgrade.Running the show version command from the CLI shows Processor having 8192K/1024K bytes of memory.Accessing the switch via the VMS management interface displays a value of 4MB.
View 5 Replies
View Related
Apr 29, 2012
I've been working on a 3560 that doesn't seem to map dscp values to a new value: mls qos map dscp-mutation ToR1 22 24 to 46
[Code]....
On the router on the other side, I created an acl that matched on dscp 46, but it doesn't match on it. I've tried moving the mutation map to the ingress interface and I've tried setting dscp with a service policy instead of marking COS and using internal dscp. Where is the mutation map supposed to be placed: ingress or egress? Also, I added an entry in the acl on the router to see if I was mapping to dscp 24, and I am:
[Code]....
So it seems like the mutation map is being ignored completely. Any reason why?
View 7 Replies
View Related
Mar 20, 2012
I've been having a debate with a colleague about QOS COS values. My colleague says I need to use COS values across layer 2 trunk links between access layer switches and core switches. My argument is if phones are marking packets with DSCP values I don't need to be concerned with Cos.The reason I ask is we're implementing a new phone system, the ip phones will mark RTP traffic wih dscp value EF and Call signaling with DSCP value of CS3. If my understanding is correct I can trust the dscp values of the phones. We are using Cisco 4507 switches which I believe automatically trust dscp values so I would just need a class-map to match the dscp values and apply the output policy map on the egress interfaces as follows? [code]
View 3 Replies
View Related
Oct 26, 2011
I'm working on a catalyst c3750 and for my work i need to prioritize certain streams independent of their bandwith usage.
The streams are the following:
- voice
- video
- data
I created policy maps based on vlans like below:
policy-map VOICE
class class-default
set precedence 5
policy-map VIDEO
[Code]...
View 7 Replies
View Related
Oct 19, 2011
I have a stack of 4 Cisco WS-C2960S-48FPS-L switches running c2960s-universalk9-mz.122-58.SE1 code. One of our network monitoring tools is indicating discards on a certain port on the switch. Upon further investigation I am seeing the Total output drops values change in a very odd manner.
The numbers seem to go from 573 to 1146 to 1719 then back down to 573 and it starts the same pattern over: [code]
The port utilization is quite low, the highest I've seen over the past 7 days is 3.5% with a polling period of every 30 seconds using Statseeker. Yet the discards are bouncing all over the place.
I've searched though the bugs for 12.2(58)SE1 and didn't see anything.
View 13 Replies
View Related
Jan 8, 2013
What are the best values for "mac address-table aging-time" and "arp timeout" by following scenarios?:- single sg300-10 as layer3-switch with a maximum of 10 local (direct connected) hosts - and a 3750x-stack with 100 local hosts + hsrp with a other stack of the same sort or for asa 5520 as internet gateway for 500 clients?I use at the moment a mac aging-time from 300 seconds and a arp timeout from 3600 seconds.
View 6 Replies
View Related
Jun 2, 2013
I am using 10Gig link to connect distribution and access switches. Since we are terminating the cables at multiple locations, we are also doing the link budgeting. The CISCO SFP 10G-LR module data sheet shows two values for the transmit power one of which is maximum power .5dBm and another is minimum power -8.2 dBm. Which value should I choose for the link budgeting.
View 1 Replies
View Related
Jan 20, 2011
As of late whenever I, or any of my roommates, browse the internet we have noticed a slower browsing experience, where pages used to load instantly, there is now a noticeable delay in accessing web pages. Also, in playing online video games, whether it be on the PlayStation 3 or PC gaming, high latency is always present. The problem is present whether there is one computer connected, or five, Mac or PC, Wireless a/b/g/n or if connected through the ethernet port. What I ask is: What causes such behavior, and what can I do, if anything, to resolve this issue?
Running a DGL-4500 D-Link Router with Comcast service.
A trace route to google shows the following:
C:UsersAdministrator>tracert www.google.com
Tracing route to www.l.google.com [74.125.224.52]
[Code].....
View 2 Replies
View Related
May 18, 2011
My CAT 4510 switch is showing 99.9% CPU usage almost through out the day. After some analysis i saw that the “Cat4k Mgmt LoPri” process is having 86% CPU utilization. This process is a package that is including multiple process.
Within this package, two processes have been identified which are causing this shock which are “K5L3Unicast Adj Tabl” and “K5 L2 Hardware Addre” .
This indicates that some heavy activity is going on CEF adjacency table and RP MAC Address Table. My current IOS version is 12.2(53)SG
View 1 Replies
View Related
Mar 6, 2013
I need to know if Catalyst 4500-X does PBR in hardware?
View 1 Replies
View Related
Feb 28, 2012
Does the 4500 support VSS (Virtual Switching System) ? On the official product overview page it says: 1.6 Terabits capacity with Virtual Switching System (hardware-ready)What means Hardware ready ? Does it mean that it supports VSS in the same manner as the 6500 ? The reason I'm asking this question is that I didn't find any info on the Internet about this. We would like to upgrade our network by interconnecting the 2 sites with Layer 2 redundant links (Layer 2 extension), but I'd like to use the both links in a load-balancing manner, which can be a real pain in the *** with STP. The choice is between 4500 and 3750 stackable core switches. The 6500s are very expensive.
View 6 Replies
View Related
Apr 3, 2013
question on 4500 SUP-7LE, this documentation is not 100% clear:
[URL]
When in single sup mode, can I have the following combinations?
1 SFP+ and 1 SFP << pretty sure this is supported
1 SFP+ and 2 SFP << think it's supported
1 SFP+ and 3 SFP << doubtful
2 SFP+ and 2 SFP << think it's supported
3 SFP+ and 1 SFP << doubtful
View 1 Replies
View Related
Nov 16, 2009
I'm seeing the following error on a 4500 running 12.2(46)SG
C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Module 5 inline power exceeds threshold: status changed to 'Pwr Over'
All the ports on module 5 have "power inline never" applied, in fact the whole switch has POE disabled.
I've attached a txt file with the show power detail output.
View 2 Replies
View Related
Apr 22, 2013
How to know 4500 SUP7-E's MIB ?Our customer use MS SCOM 2012 SP1 get the OID are 1.3.6.1.4.1.9.1.1286, but we use IOS MIB locator, we can not find this MIB id.
below are the IOS sh version information :
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 26-Apr-11 18:09 by prod_rel_team
[code]....
View 2 Replies
View Related
May 13, 2013
What is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies
View Related
Dec 14, 2011
Why Cisco 4500 R switch PBR tracking Command not working , I found just route-map next-hop ?
View 3 Replies
View Related
May 23, 2012
How i can configure the SFP Ports on my 4500 SERIES CHASSIS with other SFP ports on the connecting switch. I want to connect 15 switches via GLC=SX=MM to my 4506E sfp card.
View 4 Replies
View Related
May 15, 2013
I am getting a very strange problem where 4500 switch is remarking the packet with dscp 1 to 0.
Let me explaint the setup. I have two PCs connected on same switch but on different modules. PC1 is conencted to Gi4/19 and PC2 is connected to
Gi2/43. Both the ports has been configured to trust the dscp. Below are the configuration:
interface GigabitEthernet4/19
switchport access vlan 6
switchport mode access
[Code].....
View 7 Replies
View Related
Jan 8, 2012
I am trying to setup the WOL for our enterprise. We have a C4500 setup with mutliple Vlans. We are using Microsoft SCCM server to wake up workstations for security update. The workstations are on vlan190 and the Microsoft server is on vlan 441
Here's my config
the config below
interface Vlan190ip directed-broadcast 100 (Enables the translation of a directed broadcast to physical broadcasts)
access-list 100 remark ====== Wake-On-LAN ======no access-list 100 permit udp host 10.4.40.98 any eq 9 logaccess-list 100 remark ====== End of ACL 100 ======
[Code].....
View 2 Replies
View Related
Mar 12, 2013
We have 3 layer LAN architecture, layer 1 of 6500(IP routing), layer 2 of 4500(L2 switch only), layer 3 of 2960(L2 Switch)In a Single (2960 and 4500) Switch Port Avaya IP phone and PC are connected.Now, the requirement is that, Qos need to be configured for Voice traffic and Data traffic should be in default class of service.We plan to use COS value in Switch 4500 and 2960. We made a sample configuration as below
### For 4500 Switch
class-map match-all VOIP-Access-2MB
match cos 3 5
class-map match-all VOIP-Uplink-20MB
match cos 3 5
[code].....
check these configurations are correct as per standard and if there is any other method of configuration?What need to be configured in L3 Switch(6500)??In 2960, it doesn't support ingress QoS, what impact it will make when compare to 4500? do users experiance any difference?
View 1 Replies
View Related
Dec 10, 2012
read the posts regarding vlans that are administratively down, they suggested that they are down if no ports are assigned to them, however I do have a switchport assigned, and the interface is still down. This is on the vtp server and on the clients. The vlan is not listed when issuing show vlan brief. Other vlans configured in a similar way do show and their interfaces are up. These are two Catalyst 4948-10G.Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG5, RELEASE SOFTWARE (fc1).
View 5 Replies
View Related
May 20, 2012
I have installed a WS-X4448-GB-RJ45 on a 4503 chasis. I could not get input or output rate, just shows 0 bit/seg wether or not is forwarding traffic. I would like to know if I have to make any configuration or workaround. The IOS version is 12.2(37)SG1.
View 1 Replies
View Related
Feb 7, 2013
When I connect two 4500-x switches in a VSS setup, do I need to have both 4500-x switches equiped with Enterprise Services, or can I mix IP Base with Enterprise Services in one VSS setup in order to save on licensing costs?
View 1 Replies
View Related
Feb 14, 2012
I have a Cisco 4500 Sup 6 engine and I have two 48 port fiber line cards installed. When I do a show interfaces I do not see any of the Fiber cards. This is a new out of the box 4500 and I installed the Sup 6 Line card in Slot #1, And the two 48 port Fiber cards in Slots 2 and 3. Am I missing something, is there a command or set up procidure for the line cards. I just assumed they were plug and play
View 2 Replies
View Related
