Cisco Switching/Routing :: 4507S Not Showing Correct Information
Jun 14, 2012
Looking at the following output (show interface status) from one of our 4507s I see gig interfaces 3/2 to 3/6 are all trunked (dot1q). When I look at a show run they do not show as trunked. They should indicate switchport trunk encapsulation dot1q and switchport mode trunk (as does interface gig4/2). I have seven other 4507s all running the same IOS: 12.2(25)EWA8 and they all show the same information in show run and show interface status (as far as trunked goes). This is not a problem as I know the interfaces are trunked and working properly I am just puzzled as to why I see this difference.
Here is the sho int gig3/2 trunk. It looks like you are correct. I did not realize some were set to trunk mode on and others were not. I would think the running config would still show the port using dot1q but I guess not.
View 3 Replies
ADVERTISEMENT
Mar 2, 2011
Debug is not showing up on the console. I have configured logging console. My older switches, if an interface goes down or is brought up, it shows up on the console, but not on the new 4507s.
WS-C4507R-E
cat4500e-ipbase-mz.122-53.SG2.bin
TG-4507#sh loggingSyslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
[code]....
View 3 Replies
View Related
Nov 29, 2011
I have a cisco 5520 running as IPsec concentrator. On the ASDM homepage is shows like 31 VPN connected. But if I go to Monitor > VPN is show only 18. Then if I use SSH using sh crypto command it shows the same number as on the Monitor > VPN sections. I am running 8.3(1) and ASDM 6.3(1).
View 8 Replies
View Related
Mar 21, 2012
I got Two Distribution Switches of Cisco 3750G. Each Distribution have two 3750G switches stacked. I also have one Cisco 3750V2 Access Switch connected to both Distribution. When I am checking for redundancy, I can only get redundancy test pass for one link not atall for other. If I have a link up with Distribution 1 only then its fine; but disappointment with Distribution 2 link. I can see that the switch priorities of Dist 2 is not correct ie. Master's priority is 10 and Member's is 15.
My question is that due to misconfigured priorities on Distribution 2 stack switches I am failing with redundancy if ONLY Dist 2 is up and Dist 1 is down.
View 4 Replies
View Related
May 13, 2013
What is the correct way to lic VSS on a 4500 SUP7L-E ? url... Under Table 5 - Support by Image Type; VSS is listed as available on IP Base (SUP7E only) and a plain Yes under Enterprise Services, inferring that you need Enterprise Services lic on SUP7L-E to get VSS? url...Under Table 1 - Minimum License for VSS; IP Base or higher (7-E) or special license (7-LE and Catalyst 4500-X)Can find no option on CCO / configuration tools to list a 'special' VSS license for 4500R+E chasiss with dual SUP7L-E and IP Base.How are you meant to purchase/license VSS on 4500E Chassis + SUP7L-E ?
View 6 Replies
View Related
Jan 20, 2013
I have two cabinets in a datacentre (with 12 CAT5 links available between them), at the moment I just have a single firewall and a very basic 3Com 2824 unmanaged gigabit switch in each cabinet that are connected together. This works perfectly as the traffic use is very light and is typically server->firewall->Internet rather than too much heavy inter-server traffic.I want to improve the redundancy and reliability however. So I plan to get two Fortigate firewalls, put them in a HA cluster and have one in each cabinet with connections to the WAN. The servers are all VMware so have mulitple NICs teamed. The last bit then is between the VMware host servers and the firewalls - the switches. I'd like to have each server connected to two switches to give multiple paths, so I'm looking at two switches per cabinet. From doing a fair bit of reading it looks like I'll have no problem with this, STP should be able to sort out the multiple routes to whichever firewall is the active member at the time. There will be some need for basic VLANing as I would like to separate management traffic and certain servers I wouldn't expect to exceed 5-10 VLANs.
As I said the traffic is very light and from what I can tell I don't require any "fancy" features, and given the I need to buy four switches I'm trying choose a switch that is reliable but will do the job and not much more. If we experience growth down the road then we can buy more expensive switches then. So I've been looking at the WS-C2960-48TT-S and the WS-C2960-48TT-L, the first using the LAN Lite software while the second uses the LAN Base. The LAN Base version is virtually twice the price so I'm wondering if there are any features of LAN Base that are required in my scenario? I've done quite a bit of reading but cannot really see a reason why LAN Lite should not work fine, but don't want to discover I missed something when it is too late .
View 16 Replies
View Related
May 14, 2012
I cannot seem to correct a duplex mismatch issue.I have a Cisco 2950 switch connected to a Cisco 2621 router. I am running a per-interface Vlan. I have two fastethernet ports and one NM-1E card installed on the router. One fastethernet port is connected to my gateway router, the second fastethernet port is connected to my switch for one Vlan. The NM-1E Ethernet card is being used for the second Vlan which consists of nine IP cameras. Though the cameras on the Vlan are working fine.Now, the NM-1E card is set to half-duplex. I know that I should be using a fastethernet module like a 1FE 2W or a 2FE 2W card, (which I have,) but the router does not recogonize either one of these cards when they are installed, and yes, they have been confirmed as good cards.
Using Router-on-a-Stick configuration is out due to the bandwidth contention besides the fact that the router I am using it on will not handle this due to the flash being an older version.I have forced the switchport to half duplex, setting the speed to 10. I was getting fewer error messages at first, but they soon increased back to the frequency that they began with.I have set the switchport to duplex auto, but this failed to resolve the issue.Obviously, I cannot force the switchport into duplex full since the NM-1E interface is set to half duplex. Can the NM-1E card be configured to full duplex? I can't seem to find any documentation showing where it can be forced to full duplex mode.Could nine IP cameras just be too much for both the router and switch to handle?
View 4 Replies
View Related
Apr 22, 2012
We tested a QoS in a Cisco 3750E, IOS: 12.2(58)SE2.Voice traffice in the correct Q without any problem, but all the others traffic the Defualt Q (0), tried to capture the traffic and tcp/udp port are correct.Any thing wrong with my ACL or DSCP - CoS?? ( that ACL works fin on 4500 and 6500) [code]
View 3 Replies
View Related
Jan 1, 2012
Clarifying whats the correct # of port asic in WS-X6704-LC?According to the following link (Catalyst 6500 Architectural white paper): [URL]
"In the WS-X6704-10GE line card, there are two port ASICs each supporting 2 x 10 Gigabit Ethernet ports"
While in the document: Understanding Quality of Service on the Catalyst 6500 Switch: [URL]
Table 10.
WS-X6704
Number of 10 GE Ports 4
- QoS on 10-Gigabit Ethernet Line Cards (WS-X6704-10GE)
So whats correct? 4 port asic or 2 port asic?
# Port ASIC’s on the linecard 4
# Physical Ports per Port ASIC 1
View 1 Replies
View Related
Jan 21, 2013
I use the Switch 2960S support PoE and 10 access points cisco.I have one more question:
-- If all 10 access points cisco use copper cable to connect to 2960S, 5 access points use power adapter and 5 access points use power from Switch. How Switch 2960S will provide power for 10 AP or switch 2960S will understand and only provide power for 5 APs?
View 3 Replies
View Related
Jan 12, 2012
The network in my building consists of several 2950s connected back to 3550s using redundant fiber links and MST. Recently one tenant decided they wanted to run their own switch and use the existing building network for VoIP only which is on a dedicated VLAN. I was thinking about creating an access port on the 2950 and setting it to the VoIP VLAN as I do not want to give them a trunk port. The client can take this link and connect to their switch. So far does not seem to be an issue. Now what happens if the client configures spanning-tree on their switch? I have no control over their device and cannot manage it. Is there a way I can protect my edge switch and access port to allow them to run their own spanning tree without it interfearing with my existing MST instances? I was thinking BPDU guard but if they turn on stp and my switch sees a bpdu then the port is disabled and they lose VoIP access. At the same time I dont want them to be able to create a loop on their switch and have it affect mine. But since the is only a single cable from my device to theirs?
View 4 Replies
View Related
Jun 4, 2013
We have Cisco Catalyst 6509-V-E VSS Switch with Sup2T und IOS Version 15.0(1)SY2. We are gettin input netflow information from the gi2/3/7 but not output ... I am not sure why it does not work.
View 1 Replies
View Related
Jan 26, 2012
What is the inrush current (AC Input Surge Current) for the Cisco 2851 router? Is it the same as the router 2801?
View 1 Replies
View Related
May 22, 2012
How to get a summary of netflow statistics on NX-OS? On IOS you could do sh ip cache flow which would show what I need? Can't find a similar command on the Nexus Platform.
View 4 Replies
View Related
Mar 11, 2013
is there a command that gives me the model and serial number of the GBIC modules inside the modules of the Cisco 6500 (IOS)?
View 7 Replies
View Related
Feb 6, 2012
I come across to use the Catalyst Switch 2955 and it has two Relay Connector with one Major (MAJ) and one Minor (MIN) as below picture.There is command line to trigger these two Relay Connectors. As below command to set the Relay Connector to minor for monitoring the power supply: alarm facility power-supply relay minor
1. My questions are when there is power-supply faulty, the Minor Relay Connctor (right picture) will be short-circuited, right?
2. If we connector the two ports (ports 4 & 5 at the left picture) with a normal cable to drive an Alram Bell (in short-circuiled or closed loop situation), do we need an external power supply to the Alram Bell? Or there will be power supply from Catalyst 2955 to the Alram Bell as well?
View 1 Replies
View Related
May 1, 2013
I need to extract the serial numbers of SFPs which are plugged in a SG-200-18.For information, SG-200 doesn't have a CLI ... only a Web GUI.I just find this information : [URL]
View 2 Replies
View Related
Oct 2, 2012
I have 2 NEXUS switches in VPC. When I create/delete a VLAN gets updated in the same switch, but the VLAN information does not get propagated to the neighboring switch. Revision number remains the same even if I modify the VLAN. Had also tried changing the VTP status to transparent mode & reverting it to client mode but no luck.Have double confirmed on the VTP domain names & password. However the same setup in different location which works perfectly fine.
View 1 Replies
View Related
May 5, 2013
I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
View 1 Replies
View Related
Nov 8, 2011
My 2811 sip gateway send invite to my ITSP server with incorrect IP address in Contact section. It uses the internal ip address instead of using the public ip. As results, the re-invite sent back from ITSP sip server cannot be recieve. Could some tell how to change the ip address in Contact section of the invite message.
View 6 Replies
View Related
Nov 21, 2011
I hav e a 3750X Cisco Switch (WS-C3750X-48T-S) It is two Ethernet base SFP installed and working fine at slot 1 & 2, Now i am trying to install GLC-SX-MM in 3rd and 4th slot, but its not coming up, showing not present?
Gi1/1/1 connected trunk a-full a-1000 10/100/1000BaseTX SFP
Gi1/1/2 connected trunk a-full a-1000 10/100/1000BaseTX SFP
Gi1/1/3 notconnect 1000 auto auto Not Present
Gi1/1/4 notconnect 1 auto auto Not Present
image i am using is
C3750E-UNIVERSALK9-M
View 6 Replies
View Related
Apr 14, 2012
For an assignment in a class I am taking I created a simple network using GNS3 and set up static routing. Everything works fine, I can ping all of the hosts. One of the questions I am supposed to fill out is what happens when I use the "show ip route" and "show ip protocols" commands. When I use "show ip route" I get what seems to be the correct output. However when I use the "show ip protocols" command nothing happens. No output, no error, no nothing. It just goes right back to the prompt. This happens exactly the same on both routers in my network. incase it matters the router is c3640.
PS. would the output be non-existent because I have not set up any ip protocols. In a similar assignment I set up rip and when I used "show ip protocols" i did get what appeared to be the correct output. However I didn't write it down and when I put in the command again about an hour later after I took a break I also did not get an output until I re-entered the rip related commands.
View 2 Replies
View Related
Dec 4, 2011
We ordered the wrong part number for a Cisco 4506 non-E chassis, the part number is: WS-X4624-SFP-E and the device is showing "Unsupported module"; What would the part number be for the non-E? WS-X4448-GB-SFP,Catalyst 4500 48-Port 1000Base-X (SFPs Optional) ?
View 1 Replies
View Related
Apr 8, 2013
we have 6500 cisco switch as a backbone switch in universty. When ı want to look mac addres table , it does no show all mac address.ı mean if ı type ;show mac address-table there are not all mac address.
View 3 Replies
View Related
May 12, 2012
I have configured the following access-list on routers fa0 interface (i am using 1801)
access-list 111 permit ip any any log
and applied it in "in" direction on Fa0 interface.
Now when i am sending ssh packets to this interface its showing below
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
why its not showing any port number ?
View 1 Replies
View Related
Nov 18, 2012
I am runing 802.1x and MAB authentication of devices connected to a 3560 switch (in test). When I run 'terminal monitor' I am getting alot of authentication fail-msg. Is it possible to get the switch not to show them? I have to do some debugging on SNMP and DHCP to be able to figure out why I get these msg, but since the switch is blasting out so many auth-msg it is hard to see the debug messages. [code]
View 3 Replies
View Related
Aug 16, 2012
when I do a show module in my cat 6509, the standby sup is saying unknown, it has the same IOS as the primary card.
what does this mean? are there any tests I can run on the card?
View 2 Replies
View Related
Jun 30, 2008
Cisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
View 2 Replies
View Related
Jan 27, 2013
We have several stacks of 3750 switches where this problem is occurring. All of the switches are running IOS version 12.2(50)SE3. (Yes, I know it's old.)
We're seeing inconsistency in how the stack reports members when issuing the following commands:
sow switch
show version
show inventory
Not all members are showing up in the output of the "show version" and "show inventory" commands. For example:
HUNTI-WV-WDAC03#sh switch
H/W Current
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
1 Member 108c.cff2.ea00 15 0 Ready
2 Member 8cb6.4f0a.a600 1 0 Ready
*3 Master 8cb6.4f0a.9c00 1 0 Ready
(all three switches in stack are displayed)(code)
View 1 Replies
View Related
Mar 9, 2013
I have couple of SFP and most of them are working fine except this:-
Nexus7000# show interface ethernet 6/31 transceiver details
[code]...
a) What is the reason this is not getting recognized?
b) Is theSFP SFBR-5766PZ-CS1 plug and play in the 7000 Nexus?
View 7 Replies
View Related
Feb 4, 2010
We have a C4500 with 2 sup V which is showing high CPU values sometimes.When this occures, the switch shows 95-100% for total cpu for a few hours at a time.show proccesses cpu shows process Cat4k Mgmt LoPri with an unusual cpu value of 65% The show platform heath command gave me a high reading for K2FibFC DelFlow which is about 50% at this peak but is normaly around 1%?
what the process K2FibFC DelFlow means and what could be the cause of this peak?
View 12 Replies
View Related
Jan 22, 2013
We have 3 Cat 4500 switches on three floors teh 3rd floor switch connects to the 2nd and 4th floor switches ,but we are receiving an alert from monitoring tool that " Interface(314) Backup-1Gb-Ring is Down at least 2 min on Switch: SOM500-4510-3FL the following output from "sh int status module 1 " shows the int 1/3 and 1/4 are 'inactive'local IT guy said If the status is inactive,the ports cannot be used and might lost the capability when he added 48-port blade into the 10th slot.
2nd Floor
Port Name Status Vlan Duplex Speed TypeTe1/1 SOM500-Core1 connected trunk full 10G 10GBase-LRMTe1/2 SOM500-Core1 connected trunk full 10G 10GBase-LRMGi1/3 Backup-1Gb-Ring notconnect 1 full 1000 1000BaseSXGi1/4 Backup-1Gb-Ring connected trunk full 1000 1000BaseSX
3rd FloorPort Name Status Vlan Duplex Speed TypeTe1/1 SOM500-Core1 connected trunk full 10G 10GBase-LRMTe1/2 SOM500-Core1 connected trunk full 10G 10GBase-LRMGi1/3 Backup-1Gb-Ring inactive 1 full 1000 1000BaseSXGi1/4 Backup-1Gb-Ring inactive 1 full 1000
[code]....
View 6 Replies
View Related
Apr 23, 2012
I always though that sh mac address table dynamic interface xx/xx/xx was a subset of "sh mac address table" 6590 Version 12.2(33)SXI I have two mac addresses on downstream switches that will only show up when using
sh mac address-table dynamic interface Te4/10
* 903 0050.77a9.6e3c dynamic Yes 0 Te4/10
* 903 0050.77a9.5766 dynamic Yes 0 Te4/10
when using "old faithful"
sh mac address-table | inc 6e3c
*nothing*
or
sh mac address-table dynamic | inc 6e3c
*nothing*
nothing shows up?this vlan has no layer three interfaces
View 1 Replies
View Related
