Dell :: XPS 210 Integrated NIC Blown By Lightning
Jul 19, 2012
there was a very close lightning strike near my house and my DELL XPS 210 accessed the router before but not after. Noother elctronics, even my 2 other DELL computers were affected. I've eliminated the NIC cables, router port, everything but the actual NIC card. But diagnostics say it's working properly. Could a registry entry have been corrupted (I have a registry backup the day before). Can I replace the Integrated NIC with an internal (or external) NIC? I'm running XP Professional SP3.
View 3 Replies
ADVERTISEMENT
Apr 10, 2009
Bought a Vostro 220S about 2 months ago. After about three weeks, while I'm using it, the integrated NIC dies. All of a sudden I get the "Network Cable Disconnected" pop-up. No LEDs lit by the network jack. Contact Dell support who decides it's the motherboard.Three days later, the exact same failure. Contact support again. This time they want me to re-install Windows (yeah...right). I refused since the motherboard fixed it the first time. They finally agree to replace the motherboard again. Using the same router and cable that worked for years with my old computer. After the first failure, I switched ports on the router. While waiting for the motherboard replacements, I had installed an old PCI NIC I had laying around. Worked fine...still is. I'm not about to re-install Windows, which is what I know they'll want. I'll stick with the PCI card. Both of the people at Dell support as well as the tech they sent out told me they've not seen this before.
View 6 Replies
View Related
Aug 10, 2012
I have two of these computers side by side. The card in issue is recognized, but says no driver. I have copied the driver from the good 580e, downloaded everything I could, and cannot get it? Using Win7, 64 bit, comcast DSL. The bad one just stopped working?
View 1 Replies
View Related
Feb 16, 2013
I have integrated Intel 82577LM Gigabit Network Controller installed in my E6510.after installing updated driver from Intel and running hardware test it stopped working (displays "This device cannot start. (Code 10)" in driver details page).Also it says that device is 82577LC (it used to be 82577LM).
Intel hardware test displayed "EEPROM Failure" message. Looks like this test damaged network card firmware somehow.How do I restore/reset EEPROM of the network cad?i also tried deinstalling and reinstalling previous version of driver from Dell - no luck.
View 5 Replies
View Related
Oct 13, 2012
I recently got a Dell Latitude D600. I know, it's outdated. I'm running Windows XP SP3.
My problem is that after installing all of the drivers for the Broadcom 570x Gigabit Intergrated Controller, I can't get the wireless to pop up in the bottom right hand corner. I can only connect with an Ethernet cable directly from my router. I have tried many things, even support packages, but I can't seem to get it to work. I've also tried Fn+F2. Also, in the Device Manager I see a "Network Controller" but it has a question mark that is yellow beside it, and I can't seem to install it.
View 3 Replies
View Related
Aug 12, 2011
I've noticed that for some reason every time I can see a lightning strike outside, whether its far or near, the internet connection will go off for about 10 seconds and then come back on. This is very annoying when I'm playing Xbox Live because it kicks me every time lightning flashes.
View 13 Replies
View Related
Jul 9, 2011
I unplugged the power to my HP Win7 pc, but left the phone line hooked up to the DSL modem which was connected to the pc. Apparently, we sustained a lightning hit while we were gone. After powering up the pc, I found I had no internet access. Found the modem was bad as well as the monitor. Replaced the modem and monitor, but still no internet. Using an old pc, I have internet access. I'm guessing the motherboard also controls internet access.
View 6 Replies
View Related
Nov 2, 2009
In ordering guide, 1522 are designed to withstand power surges on the AC power cord up to 4 kV as per EN61000-4-5 Level 4 & lightning arrestors are not required.What does it means? I've install the AP outdoor & using ant58g10ssa antenna. I'm afraid the AP will struck by lightning
View 5 Replies
View Related
Sep 2, 2012
I can't get the internal 3G modem on my HP2510p with Windows 7 Professional 32 bit working. So far I've downloaded and installed the following:-
HP Broadand Wireless Modules - Sierra Wireless Inc
HP Connection Manager - Hewlett Packard
HP Wireless Assistant - Hewlett Packard
Qualcomm Gobi Driver Package for HP - QUALCOMM
but it's still saying 'no dial tone' and not reading that it has a 3G modem. If I've downloaded anything, how I can uninstall it.
View 1 Replies
View Related
Mar 28, 2011
I have two desktop PCs connected via PRO/100VE LAN and am about to replace one of these with a desktop that has Integrated 10/100/1000Base-T. Will the two machines be able to communicate? One machine will use XP Home and the new machine Windows 7.
View 2 Replies
View Related
Mar 12, 2011
What I am trying to do is port forward certain ports so the servers I'm trying to run will allow other people to connect.So far I got no where since I got a new ISP. They can't provide any assistance since I use a netgear router. One of their tech support said their modem has a built in router. The rest all said no. I noticed that the IP in CMD when I type ipconfig /all is 192.168.1.(15-47) it switches every now and then. But that is a local IP. Wouldn't that single that the modem is already routing the IP? When I put my router on it switches to 10.0.0.(2-55). These are all local IP's though. Does the modem have an integrated routing feature? Verizon really sucks so far. They can't answer their own questions without conflicting with each other.
The modem is getting the IP, and putting it into a local IP (What I believe is a routing feature) for the network. Now the local IP goes to the netgear wireless router, and gets routed again (Changed the local IP to 10.0.0.?). The netgear only got a Local IP the first time however, so the external IP is not being... worked with in the netgear router. It is trying to port forward for the local IP address, which already works for me obviously, however it is not a WAN IP address and therefore no one else is able to connect to any of my servers.And lastly, verizon states they have only "Modems" and "Wireless routers" so if they have no modems that doesn't come with this feature, then I need to learn how to port forward while the IP is being routed twice, similarly to when you have two routers hooked into each other.
View 4 Replies
View Related
Apr 25, 2011
HP just released the 8560p elitebook- not a bad shake and it actually has an integrated Serial port.Any other notebooks that have integrated serial ports?- I know the T6x Thinkpads used to use a slimbay adapter thing. I just hate the Usb adapter, and bossman said I could get a new computer here pretty soon...
View 2 Replies
View Related
May 21, 2013
How to upgrade the IOS of the Integrated wireless AP in a Cisco 881W using TFTP server (I do have software)Router side is not an issue it is the integrated AP that gives problem?
View 14 Replies
View Related
Feb 26, 2012
I have a client that that is installing a new network. They have requested the use of an CISCO891W-AGN-A-K9 mostly to be consistent with upgrades perfomed at other sites. I agree with the use of this router, so that's OK. The issue is that they have requested that I use the integrated PoE available on this model. I'm also OK with this as it will make a much neater installation. However, I can't seem to find much information on how to get the integrated PoE. I need clarification as to whether I can get a kit to upgrade this router. I generally purchase from sites like newegg or cdw (I'm an independent contractor) and I can't seem to find one with it. I have found some information on 800-IL-PM-4 and 800-ILPM-4 (who could confuse those ). Are they the same or different? Which one is the correct one and does it include the AC power adapter and can if be retro'ed into a router without the PoE?
View 2 Replies
View Related
Oct 1, 2012
I was doing some research on the Cisco ASR1001 model Router and within the description on the official Cisco page it mentions having various models that come with an "Integrated Daughter Card" or "IDC". I was curious as to what the IDC is exactly, considering there is an ASR1001 model without it.
View 2 Replies
View Related
Jun 1, 2013
I have 3850 switch with integrated WLC and i wonder if i can access the WLC via GUI ,also i need to know if it support Dynamic vlan assignment over SSID.
View 2 Replies
View Related
Jun 2, 2013
I am currently deploying Cisco ASR9K BNG solution and it needs to be integrated with a Cisco ACS 3.3 (yes that old .. going to migrate to new product in the future) equipment. There are several specific attributes need that are not on the base config of the ACS 3.3 but it seems that i can configure them manually:In addition to supporting a set of predefined RADIUS vendors and vendor-specific attributes (VSAs), Cisco Secure ACS supports RADIUS vendors and VSAs that you define. Vendors you add must be IETF-compliant; therefore, all VSAs that you add must be sub-attributes of IETF RADIUS attribute number 26..This is from the ACS 3.3 configuration manual.I have never done this user defined VSAs.
View 1 Replies
View Related
May 26, 2011
I have a HP Pavilion dv6000 with windows xp. A couple of days ago the computer couldn't find any wireless connections. I've been into devmgmt.msc and looked, but I don't see any network card. In the folder Network Connections there are three alternatives, and none are wireless...I've tried to download the drivers for chipset, modem and network, but I still can't find anything.
View 1 Replies
View Related
Mar 27, 2011
Gonna use a Dell Precision T3500 with Win7 Pro as a file server for 6 PCs. Would it be worthwhile to pick up an Intel CT pcie x1 NIC (EXPI9301CTBLK) for under $40 or just go with the integrated Broadcom 5761?
View 3 Replies
View Related
Jun 26, 2012
I am getting the new Cisco 2921/K9 router, which comes by default with 3 Integrated 10/100/1000 Ethernet ports. I have Comcast Cable as the ISP, so can I connect the ISP RJ45 Copper cable directly to one of the integrated ports or do I have to buy another WAN Interface Cards for the ISP.
View 3 Replies
View Related
Dec 28, 2011
I try to connect from my Windows 7 32bit PC with CISCO VPN Client (5.0.07.0410) to a CISCO Concentrator 3005.
Initializing the connection using certificate "xxx"
Contacting the security gateway at x.x.x.x...
Negotiating security policies...
Securing communications channel...
Secure VPN Connection terminated by Peer.
Reason 435: Firewall Policy Mismatch.
Connection terminated on: Dez 28, 2011 18:06:56 Duration: 0 day(s), 00:00.00
Not connected.
The client did not match the firewall policy configured on the central site VPN device. Cisco Systems Integrated Client Firewall should be enabled or installed on your computer.
Log on CISCO Concentrator:
32284 12/28/2011 18:06:56.620 SEV=5 IKE/141 RPT=40 x.x.x.x
Client-reported firewall does not match configured firewall: terminating tunnel.
Received -- Vendor: (0), Product (0), Caps: 0000. Expected -- Vendor: Cisco Sy
stems(1), Product: Cisco Integrated Client(0x00000001), Caps: 0002
32287 12/28/2011 18:06:56.740 SEV=5 IKE/194 RPT=8064 80.153.72.120
Group [xxx]
Sending IKE Delete With Reason message: Firewall Parameter Mismatch.
The strange thing is, that I don't have any problems with the same CISCO VPN Client on a Windows Vista PC:
32755 12/28/2011 19:04:24.540 SEV=6 IKE/143 RPT=6612 x.x.x.x
Processing firewall record. Vendor: Cisco Systems(1), Product: Cisco Integrated
Client(1), Caps: 0002, Version Number: 0.0.0.0, Version String:
View 2 Replies
View Related
Nov 3, 2011
I’m intending to establish a VPN connection between Nortel 1140E phone behind a ADSL router and a Cisco ASA 5520.can any one confirm to me if the vpn client on the Nortel 1140E phone is compatible with Cisco ASA
View 1 Replies
View Related
Mar 15, 2011
Have a customer who has two ISPs right now and only using one through a basic SOHO router. Looking to upgrade to something that supports dual WAN and allows connections from outside in on both WAN ports. There are 25-30 inside hosts.Requirements: Allow incoming connections on BOTH WAN ports to a single inside host
-This is a web app that needs as close to 100% uptime as possible
-Round robin DNS is set up
-Failover for internal people should one of the ISPs go down
Looking at either an ASA 5505 with Security Plus or an 891 Integrated Service Router.
View 1 Replies
View Related
Aug 11, 2011
I was wondering if I could use the CISCO3945 Integrated Gigabit Ethernet WAN ports for routing, I need to enable BGP and I was willing to use one of those ports.
View 2 Replies
View Related
Nov 9, 2012
I have an integrated 881W with a built in 801 access point. I'm interested in increasing the range of my AP. I'm interested in considering any configuration changes while still maintaining support for N. I've included a copy of my running config.As well, I've heard of high gain antennas. I'm using the default antennas that came with the 881W. If there are better antennas that I can buy to increase my range, I'm interested in considering that as well.
View 10 Replies
View Related
Jul 20, 2011
I've been working with a client's integrated 3750 WLC running 4.0.179.11. I want to upgrade the code because it is old plus I am having DHCP trouble. I have a couple of questions:
1. Is it OK to upgrade to SWLC3750K9-5-2-193-0.aes ? or do I need to go through 4.2 first ?
2. Will that code upgrade the bootloader at the same time?
3. How can I make sure there is enough flash space on the WLC?
4. Are there any special considerations to plan/prepare for?
The DHCP issue is failure of associated clients to get an IP address with this message found in WLC debugging:
[Code]...
View 10 Replies
View Related
May 28, 2012
We had one 877W Cisco Soho Router ,I am planing to do a Site-Site VPN connection .while i configuring the router i am facing issue in assighning IP address in BVI interface .It gave me error "integrated routing and bridging is not configured bvi" .how can i resolve the issue .
View 1 Replies
View Related
Dec 20, 2011
I remember I did that one time on 2800 router with Gi0/0 and Gi0/1 to connect another port channel in 3560G switch. I have no way to try it in ISR G2 router like 2900 or 3900 now. I know the the ethernet switch module must support it. I wonder if the integrated interfaces support it or not.
View 5 Replies
View Related
Jan 8, 2012
I came accross a Cisco 1801 router. As I understand it supposed to work with a dsl connection for internet access and configuration. I have cable internet access at home and since cisco routers are very versatile, I want to know if I can integrate this router into my home network, as a secondary router, and use it for its SSL vpn capabilities?
View 11 Replies
View Related
Mar 21, 2011
Any relevant doc for ACS4.2 on 1113 platform to be integrated with Unix Directory service having LDAP10.2.0.0 version from Oracle or guidance available.
View 1 Replies
View Related
Mar 24, 2013
I'm planning to use these with a 2504 controller. However, I cannot find a straight answer on whether or not the External Antennas provide better coverage than the Integrated Antennas? These will be wall mounted in a combo office/warehouse environment. Also, I cannot figure out if the External Antennas are even included with the 1602E (AIR-CAP1602E-A-K9)? or what if any power adapter/ injector is included with the AP's?
View 14 Replies
View Related
Sep 10, 2012
I am trying to get documentation on how to integrate an ACE30 module in a service chassis design integrated with the Nexus 7000 in routed mode. Only documentation I could find shows this design with the ACE30 module in a one arm mode. Any documentation that shows this implementation of this design?
View 2 Replies
View Related
Apr 20, 2013
open specific ports on 1941w Integrated Services Router.This specific router is a wireless VPN router that has a wired module and a wireless module and VPN so I'm getting 3 subnets on my network - 192.168.1.. for the wired connections, 10.100.1.... for wireless LAN connections and 10.100.2... for VPN remote connections.I know that by default all connected computers can access my Linux server data through telnet so the telnet port is open by default, the problem is that I have some other software licensing system on my Linux box that needs to be accessed through port 27000 and most of my users are using wireless connections and can't access that license because post 27000 is closed.what is the comand to open this post or any other port that I need to be open on the wired module, wireless module and VPN or at least poit me to somewhere where I can find all the commands that I can use for this router?
View 6 Replies
View Related
