In ordering guide, 1522 are designed to withstand power surges on the AC power cord up to 4 kV as per EN61000-4-5 Level 4 & lightning arrestors are not required.What does it means? I've install the AP outdoor & using ant58g10ssa antenna. I'm afraid the AP will struck by lightning
View 5 RepliesI've noticed that for some reason every time I can see a lightning strike outside, whether its far or near, the internet connection will go off for about 10 seconds and then come back on. This is very annoying when I'm playing Xbox Live because it kicks me every time lightning flashes.
View 13 Replies View Relatedthere was a very close lightning strike near my house and my DELL XPS 210 accessed the router before but not after. Noother elctronics, even my 2 other DELL computers were affected. I've eliminated the NIC cables, router port, everything but the actual NIC card. But diagnostics say it's working properly. Could a registry entry have been corrupted (I have a registry backup the day before). Can I replace the Integrated NIC with an internal (or external) NIC? I'm running XP Professional SP3.
View 3 Replies View RelatedI unplugged the power to my HP Win7 pc, but left the phone line hooked up to the DSL modem which was connected to the pc. Apparently, we sustained a lightning hit while we were gone. After powering up the pc, I found I had no internet access. Found the modem was bad as well as the monitor. Replaced the modem and monitor, but still no internet. Using an old pc, I have internet access. I'm guessing the motherboard also controls internet access.
View 6 Replies View RelatedHave a site that has a 1522 installed. I need to add two new outdoor AP's. Would the 1550 work along with the 1522 or would I have to replace it?
View 2 Replies View RelatedAfter a wireless network interruption, one of MAP 1522 it's not joining to WLC .
(Cisco Controller) >show ap join stats detailed 00:08:30:bb:53:20
Discovery phase statistics
- Discovery requests received.............................. 7
- Successful discovery responses sent...................... 5
[Code]....
I'm facing the following doubt regarding the AC Power Connector on the 1522 AP.We are powering up the AP through PoE, so the AC Power Connector is not used.BUT,do i have to seal/protect the connector or leave it as is?
View 3 Replies View RelatedI'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
I have a wireless sytem with a WLC 4400 and several 1522 Access Points. They don't actually function as Access Points because I'm using radio communication only for backhaul. There are no clients connected to the Access Points. All traffic on the network comes from the devices connected on the LANs that are bridged through the APs ethernet port.
I would like to create filters to allow only certain devices to be able to transmit over the radio link. I've used this in the past on 1310 units and it was very easy to do via GUI. This filter could be either by IP or MAC Addresses. IP would be better for me.
I loose the ability to connect and I was thinking if I could extend the wireless network by adding a DAP-1522.I want to have the WNDR3700 and the DAP-1522 connected via wireless and using a laptop I want to be able to access the wired network from anywhere in the facility.
I connected AP 1522 to AC power source and this is the message that i received on the console port.
%CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (0000.0000.0000)
Why this message apear ?This is not sufficient power to bring up radio interfaces?
They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
View 14 Replies View RelatedClient has existing 1522 outdoor access points over different branches.1522 is dicontinued and 1552 is the replacement AP.Client intends to extend their outdoor wireless with the new AP's.Are there any known issues if the 1552 is mixed with 1522 envi?,Is a separate controller required for the new AP's?Will MESH work between 1522 and 1552 AP's?
View 3 Replies View RelatedI have a cisco air lap 1522 but i have problem with it! I cant use config command in cli ? And i cant assign ip address to ap.
View 19 Replies View RelatedI got a DAP-1522 and here is my situation. I have a wireless router connected to the internet downstairs. I want to extend the range by creating a new wireless network upstairs. So I want the DAP-1522 to connect to the wireless router, and then become another access point upstairs.
I was able to connect to the wireless router in the DAP-1522 setup wizard, but nowhere was I able to configure that actual DAP-1522 WIRELESS setup. Nothing ever showed up on the "Wireless Settings". Just "Save Settings" "Do Not Save Settings" and the rest of the screen empty. On the status page it does show it is connected.
Am I doing something wrong or will the DAP-1522 not do this?
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies View RelatedI have a defective DAP-1522, or what. First off, I have never been able to access the unit at http://DLINKAP when my computer is connected directly to the 1522 via ethernet, only 192.168.0.50 works to bring up the web interface.
Second, I have more than one AP at my house, but the DAP-1522 is the only networking device I have have problems with (I am using the unit in AP mode). Basically, the problem is the wireless connection usually is much slower than my other APs (both N and G), even when the computer is physically right next to the DAP-1522. And that's when the unit is at it's best. At it's worst, I can't connect to the internet at all, even though my laptop shows full signal strength. The 1522 just seems really finicky. The problem doesn't seem to be a networking issue, because a 2nd AP that is connected through the wired portion of the DAP-1522 works perfectly, implying the 1522 is having no networking issues when using the ethernet ports. But since the problems persist with full signal strength and with the computer right next to the 1522, it doesn't seem to be a wireless connection issue either. And I have no problems connecting to any other wireless APs I own (and I own about 5 others, not that I use them all at the same time).
If I could, I would return my 1522, but I've been tinkering with it for too long now to return it. It has caused me a ton of frustration. I had a wired-only router for a long time (hence the purchase of the 1522), but just bought a new wireless-N router that is performing perfectly (as a router, and as an N AP). I hoped the old router might have not been playing nice with the 1522, but have seen no improvement with the 1522 wired to the new router (on opposite ends of my home).
Note that I use Macs only, no Windows machines. I started with the 1.02 firmware for the 1522, now have 1.20 firmware, but have noticed no improvements with my issues.
how to configure AP1522 in my possession.
I have 2 AP1522 and I have to configure them so that clients can connect either 2.4 GHz or 5.0 GHz. Each of the two AP1522 must be autonomous, but has to bear in mind that are close together.
To do this I have:
- Defined the two AP1522 as RAP mode
- Set the flag on the "client access on backhault link", but I have not enabled the sub-flag "Extended backhaul Client Access" (what is this sub-flag?)
- Set 2 BGN different (but this is indispensible or I can put the same BGN? what is the difference?)
- Set the two AP1522 on two different channels (but this is necessary? or is importan only if I set the same BGN?)
- The two AP1522 appear on the WLC as a way bidge (is correct?)
How can I check if my laptop will connect using the 5.0 GHz?!? It's just turn off the antenna of 2.4 GHz?!? On my laptop I haven't found a way to force it to connect in 5.0 GHz.
I'm facing a problem with the Cisco 1522 AP at the remote site every day that it takes about 2 hours to join the WLC, is there any way to minimize the time that the mesh 1522 AP takes to join the WLC?
View 2 Replies View RelatedI am facing problem with an outdoor access point AIR-1522-K-E series which is unable to join a wirless lan controller 5508. The wireless AP is able to get IP address from dhcp server and discover the Wireless controller IP address. After this i see following status messeges on the console of AP.
*Aug 27 11:04:19.767: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 27 11:04:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.2.64.50 peer_port: 5246
*Aug 27 11:04:21.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Aug 27 11:04:21.707: %CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.2.64.50 peer_port: 5246
[Code]...
Using as AP. Last Tuesday in the middle of a Netflix movie the video stopped. Now the wireless portion of the DAP-1522 refuses to pass any type of video. Everything else works (email, Google, Facebook, etc.). I can get to Netflix, Youtube, Yahoo, etc. .....but none of them will pass video.
Using a direct wired connection to the DAP-1522 everything works. Netflix, Youtube, etc.
Download speed checks at 17.74mbps.
I'm setting up A DAP-1522 in bridge mode. Network setup went fine. When I went to wireless setup I got a blank page, all white no letters, nothing. I've logged out and back in again with the same results.
View 8 Replies View RelatedI'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I am thinking of getting the DAP-1522 access point but I wondered. Can I set it to broadcast on 5GHz for my laptop and ipad, so they can stream video. Then set the guest zone to broadcast on 2.4GHz just for my lame printer, my printer does not have LAN and only wireless b & g. If I do put the printer on the guest zone and I enable routing between zones, will my laptop be able to print to my printer?
View 1 Replies View RelatedI have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies View RelatedIf I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedSo just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
I have deployed 2 x Cisco 1522 mesh access point and configured both as root ap. On top of that, I have also customized the power setting for the 802.11a/n signal to value 5. However, I discovered that whenever the mesh APs reboot, the power of 802.11a/n signal to will be reset to value 1.
Thus, I would like to ask is this a norm behaviour or I have mis-configured some setting?
i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
View 1 Replies View RelatedI upgraded the firmware on my newly acquired DAP-1522 from v1.02 to v1.21 (the hardware ver is A1). But weird thing happened after the upgrade--the Setup->wireless network settings portion of the set up menu disappeared! I re-flashed the upgrade once more and it's still not showing. Reboot the AP--same thing!
[url]...
With firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
View 6 Replies View RelatedHere's the setup:
DGL-4100 (wired gigabit router)
-> Wii
-> X360
-> PS3
-> DGS-2205 (wired gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522 (wireless access point/bridge)
Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.
We have a Cisco 1522 ap bridge running on a controller and we want to create a wireless bridge from the Cisco AP to a Mikrotik SXT5HPND wireless router to a cisco 2960s switch
How to bridge a cisco device with a mikrotik device, but there are plenty who do mikrotik to mikrotik bridging..