Cisco Wireless :: Airlap 1522 Cannot Configure Command In Cli
Aug 24, 2012I have a cisco air lap 1522 but i have problem with it! I cant use config command in cli ? And i cant assign ip address to ap.
View 19 Replies
ADVERTISEMENT
Cisco Wireless :: Configure AP 1522 To Accept Client Access On 2.4 And 5.0 Ghz?
May 5, 2013 how to configure AP1522 in my possession.
I have 2 AP1522 and I have to configure them so that clients can connect either 2.4 GHz or 5.0 GHz. Each of the two AP1522 must be autonomous, but has to bear in mind that are close together.
To do this I have:
- Defined the two AP1522 as RAP mode
- Set the flag on the "client access on backhault link", but I have not enabled the sub-flag "Extended backhaul Client Access" (what is this sub-flag?)
- Set 2 BGN different (but this is indispensible or I can put the same BGN? what is the difference?)
- Set the two AP1522 on two different channels (but this is necessary? or is importan only if I set the same BGN?)
- The two AP1522 appear on the WLC as a way bidge (is correct?)
How can I check if my laptop will connect using the 5.0 GHz?!? It's just turn off the antenna of 2.4 GHz?!? On my laptop I haven't found a way to force it to connect in 5.0 GHz.
Cisco Wireless :: AIR-LAP1242AG-A-K9 Configure Command Doesn't Seem To Exist
Oct 21, 2007I have an AIR-LAP1242AG-A-K9. Straight out of the box I thought it would have the GUI functional but this is not the case. I am brand new to Cisco products so it is taking me a while to get use to them and to TelNet but from what I have read in about 6 different manuals none have explained how I can access the configure terminal command when It doesn't show up. I am in privileged mode with access of: AP001c.588e.a266#show privilege. Current privilege level is 15.If I can't get into global configuration mode I cant enable the GUI, turn on the wireless.
View 6 Replies View RelatedCisco Wireless :: Configure Access On 877 Router Either On Command Line Or GUI?
Apr 30, 2012i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies View RelatedWay To Comment For Command When Configure Switch
Jan 7, 2012I want write comment for command when i config switch .i want when use show running display comment .
View 1 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.2 Configure Command Set Only To Allow Interface Access?
Jul 6, 2011I had insatalled the ACS 5.2 on Vmware . As per my requirement i need to configure a user to restricted privilege so that he should be able to execute only the below commands on the switch .
-Show ver
-Show interfaces
-Show ip Interface Brief
-Configure terminal
-Interface <interface name >
-Shutdown
-No shutdown
The users should not be authorized to execute any other commands than above listed one .After the configuration i was not able to restrict the config mode commands . Once the user is authoized for Configure terminal access he will have full access on the device. How to configure the command set only to allow interface access and he should be able to apply Shutdown and No shutdown command .
Cisco WAN :: Configure Policy-map With Police Command At Router 7606-S?
Dec 27, 2011Im having problem configuring policies for limiting traffic on subinterfaces on cisco Router 7606-S. I have configured:
[code]...
So for egressQOS , i want to configure with police, not shape (for the memory reason).
Cisco Switching/Routing :: 7600 / ES20+ Configure Global Command Mls Qos
Dec 18, 2012ES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
Cisco Switching/Routing :: Equivalent Command To Configure On Nexus 5596
Jun 21, 2012what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies View RelatedCisco WAN :: Unable To Configure Service Policy Output Command In 2921 Router
Apr 25, 2011I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies View RelatedCisco VPN :: 5520 Configure Intra Interface Command To Enable Connectivity Between Remote Clients
Feb 3, 2013I'm working with AnyConnect for the first time (my prior experience is with IPSec client) and I have multiple remote users who connect to a 5520 via AnyConnect client; they need to print to each others' shared printers but currently have no connectivity between each other.
Can I configure the 'intra-interface' command to enable connectivity between remote clients, or is there more that needs to be done to enable this, presuming that it can be done at all?
Cisco Wireless :: 1522 Need To Add Two New Outdoor AP
Mar 9, 2012Have a site that has a 1522 installed. I need to add two new outdoor AP's. Would the 1550 work along with the 1522 or would I have to replace it?
View 2 Replies View RelatedCisco Wireless :: 1522 - AP Not Joining To WLC
Mar 19, 2012After a wireless network interruption, one of MAP 1522 it's not joining to WLC .
(Cisco Controller) >show ap join stats detailed 00:08:30:bb:53:20
Discovery phase statistics
- Discovery requests received.............................. 7
- Successful discovery responses sent...................... 5
[Code]....
Cisco Wireless :: 1522 AC Power Connector
May 13, 2010I'm facing the following doubt regarding the AC Power Connector on the 1522 AP.We are powering up the AP through PoE, so the AC Power Connector is not used.BUT,do i have to seal/protect the connector or leave it as is?
View 3 Replies View RelatedCisco Wireless :: 1522 MAP Through 1042 RAP Not Working?
Mar 25, 2012I'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
Cisco Wireless :: 4400 - IP Or MAC Filter On 1522 AP?
May 21, 2013I have a wireless sytem with a WLC 4400 and several 1522 Access Points. They don't actually function as Access Points because I'm using radio communication only for backhaul. There are no clients connected to the Access Points. All traffic on the network comes from the devices connected on the LANs that are bridged through the APs ethernet port.
I would like to create filters to allow only certain devices to be able to transmit over the radio link. I've used this in the past on 1310 units and it was very easy to do via GUI. This filter could be either by IP or MAC Addresses. IP would be better for me.
Way To Connect WNDR3700 And DAP-1522 Via Wireless
Apr 18, 2012I loose the ability to connect and I was thinking if I could extend the wireless network by adding a DAP-1522.I want to have the WNDR3700 and the DAP-1522 connected via wireless and using a laptop I want to be able to access the wired network from anywhere in the facility.
Cisco Wireless :: LAP 1522 / All Radio Interfaces Disabled
Sep 26, 2012I connected AP 1522 to AC power source and this is the message that i received on the console port.
%CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (0000.0000.0000)
Why this message apear ?This is not sufficient power to bring up radio interfaces?
Cisco Wireless :: AIR-LAP 1522 To Connect To Console Port
Sep 5, 2012They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
View 14 Replies View RelatedCisco Wireless :: Mixing 1522 And 1552 Outdoor AP
Jun 13, 2013Client has existing 1522 outdoor access points over different branches.1522 is dicontinued and 1552 is the replacement AP.Client intends to extend their outdoor wireless with the new AP's.Are there any known issues if the 1552 is mixed with 1522 envi?,Is a separate controller required for the new AP's?Will MESH work between 1522 and 1552 AP's?
View 3 Replies View RelatedCisco Wireless :: Lightning Arrestors For Aironet 1522?
Nov 2, 2009In ordering guide, 1522 are designed to withstand power surges on the AC power cord up to 4 kV as per EN61000-4-5 Level 4 & lightning arrestors are not required.What does it means? I've install the AP outdoor & using ant58g10ssa antenna. I'm afraid the AP will struck by lightning
View 5 Replies View RelatedD-Link DAP-1522 :: Nothing Showing In Wireless Setting?
Mar 23, 2011I got a DAP-1522 and here is my situation. I have a wireless router connected to the internet downstairs. I want to extend the range by creating a new wireless network upstairs. So I want the DAP-1522 to connect to the wireless router, and then become another access point upstairs.
I was able to connect to the wireless router in the DAP-1522 setup wizard, but nowhere was I able to configure that actual DAP-1522 WIRELESS setup. Nothing ever showed up on the "Wireless Settings". Just "Save Settings" "Do Not Save Settings" and the rest of the screen empty. On the status page it does show it is connected.
Am I doing something wrong or will the DAP-1522 not do this?
D-Link DAP-1522 :: Does WoL Work If PC Is Behind Wireless Bridge
Jan 28, 2010I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies View RelatedD-Link DAP-1522 :: Wireless Connection Usually Much Slower Than Other AP
Jan 22, 2009I have a defective DAP-1522, or what. First off, I have never been able to access the unit at http://DLINKAP when my computer is connected directly to the 1522 via ethernet, only 192.168.0.50 works to bring up the web interface.
Second, I have more than one AP at my house, but the DAP-1522 is the only networking device I have have problems with (I am using the unit in AP mode). Basically, the problem is the wireless connection usually is much slower than my other APs (both N and G), even when the computer is physically right next to the DAP-1522. And that's when the unit is at it's best. At it's worst, I can't connect to the internet at all, even though my laptop shows full signal strength. The 1522 just seems really finicky. The problem doesn't seem to be a networking issue, because a 2nd AP that is connected through the wired portion of the DAP-1522 works perfectly, implying the 1522 is having no networking issues when using the ethernet ports. But since the problems persist with full signal strength and with the computer right next to the 1522, it doesn't seem to be a wireless connection issue either. And I have no problems connecting to any other wireless APs I own (and I own about 5 others, not that I use them all at the same time).
If I could, I would return my 1522, but I've been tinkering with it for too long now to return it. It has caused me a ton of frustration. I had a wired-only router for a long time (hence the purchase of the 1522), but just bought a new wireless-N router that is performing perfectly (as a router, and as an N AP). I hoped the old router might have not been playing nice with the 1522, but have seen no improvement with the 1522 wired to the new router (on opposite ends of my home).
Note that I use Macs only, no Windows machines. I started with the 1.02 firmware for the 1522, now have 1.20 firmware, but have noticed no improvements with my issues.
Cisco Wireless :: Remote Site 1522 AP Connecting Delay With WLC Every Day
Jul 29, 2011I'm facing a problem with the Cisco 1522 AP at the remote site every day that it takes about 2 hours to join the WLC, is there any way to minimize the time that the mesh 1522 AP takes to join the WLC?
View 2 Replies View RelatedCisco :: AIR 1522 Error In Joining Wireless LAN Controller 5508
Aug 27, 2011I am facing problem with an outdoor access point AIR-1522-K-E series which is unable to join a wirless lan controller 5508. The wireless AP is able to get IP address from dhcp server and discover the Wireless controller IP address. After this i see following status messeges on the console of AP.
*Aug 27 11:04:19.767: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 27 11:04:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.2.64.50 peer_port: 5246
*Aug 27 11:04:21.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Aug 27 11:04:21.707: %CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.2.64.50 peer_port: 5246
[Code]...
D-Link DAP-1522 :: Will Not Pass Video Stream Via Wireless
Nov 8, 2011Using as AP. Last Tuesday in the middle of a Netflix movie the video stopped. Now the wireless portion of the DAP-1522 refuses to pass any type of video. Everything else works (email, Google, Facebook, etc.). I can get to Netflix, Youtube, Yahoo, etc. .....but none of them will pass video.
Using a direct wired connection to the DAP-1522 everything works. Netflix, Youtube, etc.
Download speed checks at 17.74mbps.
D-Link DAP-1522 :: Blank Page In Wireless Setup?
Dec 14, 2011I'm setting up A DAP-1522 in bridge mode. Network setup went fine. When I went to wireless setup I got a blank page, all white no letters, nothing. I've logged out and back in again with the same results.
View 8 Replies View RelatedD-Link DAP-1522 :: Wireless MAC Cloning In Bridge Mode?
May 16, 2011I'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
D-Link DAP-1522 :: Guest Zone For Wireless Printer
Mar 3, 2013I am thinking of getting the DAP-1522 access point but I wondered. Can I set it to broadcast on 5GHz for my laptop and ipad, so they can stream video. Then set the guest zone to broadcast on 2.4GHz just for my lame printer, my printer does not have LAN and only wireless b & g. If I do put the printer on the guest zone and I enable routing between zones, will my laptop be able to print to my printer?
View 1 Replies View RelatedD-Link DAP-1522 :: Access Configuration Pages Via Wireless
Jan 9, 2012I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies View RelatedD-Link DAP-1522 :: Bridge Mode - Turn Off Wireless?
May 30, 2012If I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedD-Link DAP-1522 :: To Work As Wireless Access Point To DIR-825
Jun 4, 2011So just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.