Cisco Wireless :: AIR-LAP1242AG-A-K9 Configure Command Doesn't Seem To Exist
Oct 21, 2007
I have an AIR-LAP1242AG-A-K9. Straight out of the box I thought it would have the GUI functional but this is not the case. I am brand new to Cisco products so it is taking me a while to get use to them and to TelNet but from what I have read in about 6 different manuals none have explained how I can access the configure terminal command when It doesn't show up. I am in privileged mode with access of: AP001c.588e.a266#show privilege. Current privilege level is 15.If I can't get into global configuration mode I cant enable the GUI, turn on the wireless.
View 6 Replies
ADVERTISEMENT
Jun 5, 2013
I'm having an issue with port-security on a cisco 2950 switch. The port-security is setup to user sticky mac-addresses and was working just fine. Recently when a computer was changed out and I needed to clear the security on the port it wouldn't let me.I would type clear port-security sticky int fa0/## and it would give me an error. The error would be that the sticky command doesn't exist.So I went back and type clear port-security ? and the only option was dynamic. Even if I try to take the port security off the switch it wont let me, it never shows the option for sticky.If I change the maximum number of mac-addresses allow the computer will work, but I can never clear the old addresses out.
View 3 Replies
View Related
Jun 16, 2012
How to connect my Windows XP Desktop to my homes wireless network system (my comp is outdated I know ). I have no trouble with my my mum's Windows 7 Laptop and no problems with my MacBook Pro, but how do I connect this old clunky XP to it?
Wireless Connections doesn't exist in my network connections tab, and in Services under Admin Tool - in the 'Wireless Zero Configuration Properties' is set to Automatic startup type and it is 'started'.
View 1 Replies
View Related
Oct 21, 2012
I am using ASA 5520 Image in GNS3, when i come in Configuration Mode and try to create Tunnel through command "interface Tunnel 0", but this command doesn't exist. I need this command to create Tunnel for GRE Lab.
View 2 Replies
View Related
Jul 29, 2012
Is possible to configure a Lightweight Access Point LAP1242AG as 802.1x supplicant using Microsoft NPS radius server that not use EAP-FAST authentication method? Can I use PEAP in NPS radius?
View 6 Replies
View Related
Nov 19, 2012
EA4500 router setting currently I am on an single fix IPs network, Internet access filtering by a Fortigate gateway, some IPs has Internet access, most of the IPs without, and we like to keep it that way.may I know what is the proper way to configure the newly added EA4500 router to working with "Guest Access" and my existing fix IPs network?
View 9 Replies
View Related
Jul 26, 2011
I have created a VPN client account on my RVS4000 router. I have installed Quick VPN on my laptop in the default directory -- Program Files (x86) / Cisco Small Business / Quick VPN Client
I have generated and exported a certificate -- RVS4000_Client.pem -- and placed that in the Program Files (x86) / Cisco Small Business / Quick VPN Client directory. When I attempt to connect using the Quick VPN client, I get the warning "Server's certificate doesn't exist on your local computer."
If I ignore the message I can log in, and ping resources inside the network and log into the router. However, I cannot mount any drives and the router shows that no VPN tunnels exist. I've read several posts here and elsewhere and can't seem to see where I've gone wrong.
View 1 Replies
View Related
Jan 8, 2013
I am getting Authorisation requests failed log entries for a user however there aren't any successful authentication logs.
The user would never be able to authenticate as it no longer exists in ACS (it was the user for someone who left the company 3-4 month ago)
The other wierd thing is that the caller-id is 0.0.0.0 BTW the NAS is a Cisco ASA firewall running 8.0(3)
View 4 Replies
View Related
Dec 19, 2011
After a day of troubleshooting I have finally got the QuickVPN client to work. I connect however during the connection I get: "Server's certificate doesn't exist on your local computer. Do you want to quit this connection?" I click no and it connects fine other than this error. So how do I get rid of this error? Also I have exported the client certificate from the RV110 and put it in the quickvpn directory as I saw suggested elsewhere.
Here is my log:
2011/12/21 00:39:44 [STATUS]Connecting...
2011/12/21 00:39:44 [DEBUG]Input VPN Server Address = ***.***.***
2011/12/21 00:39:45 [STATUS]Connecting to remote gateway with IP address: **.**.**.***
2011/12/21 00:39:50 [WARNING]Server's certificate doesn't exist on your local computer.
2011/12/21 00:39:56 [STATUS]Remote gateway was reached by https ...
[code]....
View 2 Replies
View Related
May 7, 2012
I bought a new WRVS400n recently because it had Gigabit speed, wireless n and a built in VPN server. The device works perfect except for the Quick VPN client. I'm a system engineer so I thought I could set it up quite easy just like any other device I configured in the past. Painfull but it isn't like this.
I set up the VPN on the WRVS4400n and generated a certificate. I saved both the client and admin certificate to my pc, I gave them a name to easily make up the difference between both of them. When placing the certificate in the installed QuickVPN folder, it doesn't seem to get recognised by the QuickVPN software. When I try to connect, it says 'Server's certificate doens't exist on your local computer'. I guess the naming convention must meet some kind of format, is that correct? If so, this should have been described in the documentation.
Besides that I checked if the required ports used by the VPN server are open on the public port of the device, that is the case. So It seems I'm quite close to get it working.
The version of QuickVPN I used is 1.4.2.1. The WRVS4400n has the latest firmware loaded.
View 1 Replies
View Related
Aug 24, 2012
I have a cisco air lap 1522 but i have problem with it! I cant use config command in cli ? And i cant assign ip address to ap.
View 19 Replies
View Related
Nov 11, 2012
I have a CISCO AIR-LAP1242AG-A-K9 Wireless Aironet 1240AG and i do not have any wireless controllers i just want this to act as a AP and not have to depend on any thing else for its config. I can not get the IOS to TFTP over. Here are the steps i take.
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30. The IP address of the AP is 10.0.0.1.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cross over cable .
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release. You will see the IOS file being TFTP to the AP. Once this is done on the screen reboot the AP by pulling out the power cable.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
View 35 Replies
View Related
Apr 30, 2012
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies
View Related
Jul 7, 2011
I setup a mini wireless LAN network lab with a not for resale 2106 wireless lan controller and a sales air-lap1242ag access point. I do not have a DHCP and DNS in my lab environment. I have configured the WLC with the basic configuration using the CLI wizard, i also configured the WLC as a DHCP server for clients that will be connecting to the APs associated to the controller.
I powered up the AP and connect the ethernet port directly to the controller, the controller issued an IP address to the AP, the AP downloaded a new operating system from the controller but failed to join the controller.
I check both debug message on the controller console and the trap messages on the controller's GUI and it say the AP could not download a configuration from the controller and it is beacuse of invalid license. Below is the trap message:
Configuration Phase Statistics Requests ReceivedResponses SentUnsuccessful Request ProcessedReason For Last Unsuccessful AttemptLast Successful Attempt TimeLast Unsuccessful Attempt TimeLast Error SummaryLast AP Message Decryption FailureLast AP Connection FailureLast Error Occurred Last Error Occurred ReasonLast Join Error Timestamp
Also, I tried to log into the GUI of the AP using the both the username and password ''Cisco'' but I cannot get into the device. I can only get in through the CLI. In the CLI, almost all the commands I enter gives an error the it is disabled. I don't know what to do any more, I want to know if the access point is faulty or i am not doing the right thing.
View 4 Replies
View Related
May 8, 2012
I would like to implement a zone based firewall on my ASA5510. Is ZBF possible on ASA? or is it strictly for routers? I know we've implementd ZBF using Sonicwall firewalls before. A little confused here as to why my ASA doesnt have the right commands.Maybe my version of ASA software is too old? It's 8.2 if i remember right.
View 11 Replies
View Related
May 31, 2013
I am wondering if anyone has seen this before. We have about 50 AIR-LAP1242AG-E-K9 access points connected to a WLC5508 running 7.4.100.0. These were all being used as autonomous APs previously and were converted when the controller was installed. About 12 of these have a lovely feature where their radio interface goes down at random. The radio is still in enable mode but the opertational status is DOWN. It seems to happen particularly when there has been a power outage and the AP rejoins the controller. All of the other 1242s are fine and never sees this problem. The APs are all on power injectors.
Once the radio is down, the only way I can get the to come back online is by doing the following:
1. Set the radio admin status to "disable" and apply
2. Turn off CDP
3. Reboot the AP Wait until the AP is back online and registered on the controller
4. Enable the radio admin status and CDP.
If I do not remove the CDP setting I cannot bring the radio back to "UP". I know we had previous issues with autonomous 1242 APs that did not like CDP being enabled. Have I perhaps got a bunch that are like that? Despite these having operated as autonomous APs they are AIR-LAP1242 from the factory.
View 6 Replies
View Related
Apr 2, 2012
I have successfully converted my lap1242ag-c-k9 to autonomous mode. But when i try to set ssid or wep then hit apply it won't the changes i made.
View 3 Replies
View Related
Jul 16, 2012
We ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas instead of the 2.4GHz antennas.Would it be possible to use the 5GHz antennas as 2.4GHz antennas?If so, are there any down sides to it?
View 15 Replies
View Related
Jun 26, 2011
The Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies
View Related
Jan 7, 2012
I want write comment for command when i config switch .i want when use show running display comment .
View 1 Replies
View Related
Jul 6, 2011
I had insatalled the ACS 5.2 on Vmware . As per my requirement i need to configure a user to restricted privilege so that he should be able to execute only the below commands on the switch .
-Show ver
-Show interfaces
-Show ip Interface Brief
-Configure terminal
-Interface <interface name >
-Shutdown
-No shutdown
The users should not be authorized to execute any other commands than above listed one .After the configuration i was not able to restrict the config mode commands . Once the user is authoized for Configure terminal access he will have full access on the device. How to configure the command set only to allow interface access and he should be able to apply Shutdown and No shutdown command .
View 6 Replies
View Related
Dec 27, 2011
Im having problem configuring policies for limiting traffic on subinterfaces on cisco Router 7606-S. I have configured:
[code]...
So for egressQOS , i want to configure with police, not shape (for the memory reason).
View 4 Replies
View Related
Mar 27, 2013
What I have. 2 - WLC2125 controllers. Second unit is failover purpose only.
19 - Cisco Access points. AIR-LAP1242AG-A-K9 - All powered by Cisco Power Injector AIR-PWRINJ3.
Issue: 5 AP's in another building loses connection to the network and drops off from the Controller. Sometimes it's all of them. Sometimes it's just 1 or 2 or 3 of them. Happens very randomly. Somtimes once a week. Sometimes, once every two weeks. Only way that I know how to get them back up is to just power cycle them. Once power cycled it comes right back up.
This has been happening for awhile now and I really need to get to the bottom of this. I understand it can be number of issues, like cabling, or power issues but what I really need is a steps to troubleshoot to narrow down. what to look for, settings on controller? etc...
View 14 Replies
View Related
Dec 18, 2012
ES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
View 2 Replies
View Related
Jun 21, 2012
what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies
View Related
Oct 20, 2012
I've got a LAN set up with a server and printer, no internet connectivity to it. When I need to access the internet, I connect through a wireless hotspot. The only problem is that I have to unplug the ethernet from my LAN connection for the wireless to work.Is there a way to have both connections coexist, so that when I need to print something or access a file on my server I can do so without it interfering with my internet connection?
View 4 Replies
View Related
Apr 25, 2011
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies
View Related
Feb 20, 2012
I'm setting up a couple 881W cisco routers to use Unified wireless and am running into a bit of a brick wall.I've read through the "Upgrading to Unified Cisco Software" section of the following article:[URL]The problem is, I can't run the "service-module wlan-ap0 bootimage unified" command. The keyword "bootimage" does not exist. The router is licensed for advipservices and I'm running version 15.0(1)M4 on the router. AP is currently running version 12.4(21a)JA1. why the bootimage command doesn't appear? Will I need to downgrade the router IOS to 12.4?Additionally I'm having trouble finding an answer to the following:Is there a way to set up the embedded AP on the same network as the Data VLAN on the router, or do I need to create a separate IP network for the embedded AP? I've tried using 'ip unnumbered vlan10' (vlan10 is the data vlan) on the wlan-ap0 interface but then when I try opening a session to the AP it doesn't connect.
bcp4n51001#service-module wlan-ap0 session
Trying 10.199.62.1, 2002 ...
% Connection timed out; remote host not responding
This is my Vlan10 setup for one of the routers:
interface Vlan10
ip address 10.199.62.1 255.255.255.0
ip helper-address 10.151.103.254
ip helper-address 10.150.1.254
ip pim sparse-mode
View 8 Replies
View Related
Oct 30, 2012
Received Error:Object "Dot11BandSelect" does not exist. when configuring the 802.11 settings on a 4400 WLC runing ver. 6.0.196.0
View 1 Replies
View Related
Feb 3, 2013
I'm working with AnyConnect for the first time (my prior experience is with IPSec client) and I have multiple remote users who connect to a 5520 via AnyConnect client; they need to print to each others' shared printers but currently have no connectivity between each other.
Can I configure the 'intra-interface' command to enable connectivity between remote clients, or is there more that needs to be done to enable this, presuming that it can be done at all?
View 3 Replies
View Related
Dec 8, 2012
-Model : TL-WR1043ND
-Hardware Version : v1
-Firmware Version : 120605
I'm wondering if USB HDD spin down capability does exist on the deviceI think this enhancement will be serve a lot of costumers who wish to use all USB features.
View 1 Replies
View Related
Jun 14, 2012
Access Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies
View Related
Apr 28, 2013
a have a router CISCO 1841 and I configured a NAT inside from the router to the firewall like this :ip nat inside source static firewall_adresse public_adresse and its work fine and when a added it I do this command "wr" to save the configuration and I restarted the router many times and it still work fine,but in the last five months this NAT does not exsit twice and I must add it a gain.
View 7 Replies
View Related
