Cisco Wireless :: 881W - Unified Setup / Bootimage Does Not Exist?
Feb 20, 2012
I'm setting up a couple 881W cisco routers to use Unified wireless and am running into a bit of a brick wall.I've read through the "Upgrading to Unified Cisco Software" section of the following article:[URL]The problem is, I can't run the "service-module wlan-ap0 bootimage unified" command. The keyword "bootimage" does not exist. The router is licensed for advipservices and I'm running version 15.0(1)M4 on the router. AP is currently running version 12.4(21a)JA1. why the bootimage command doesn't appear? Will I need to downgrade the router IOS to 12.4?Additionally I'm having trouble finding an answer to the following:Is there a way to set up the embedded AP on the same network as the Data VLAN on the router, or do I need to create a separate IP network for the embedded AP? I've tried using 'ip unnumbered vlan10' (vlan10 is the data vlan) on the wlan-ap0 interface but then when I try opening a session to the AP it doesn't connect.
bcp4n51001#service-module wlan-ap0 session
Trying 10.199.62.1, 2002 ...
% Connection timed out; remote host not responding
This is my Vlan10 setup for one of the routers:
interface Vlan10
ip address 10.199.62.1 255.255.255.0
ip helper-address 10.151.103.254
ip helper-address 10.150.1.254
ip pim sparse-mode
View 8 Replies
ADVERTISEMENT
May 16, 2012
I'm in the process of setting up a working VPN/Firewall setup on an 881W ISR. I have the firewall, NAT, and VPN working, and I'm able to connect remotely to my router. The problem I am having is that I none of my VPN cllients can connect to the internet. I suspect that my firewall rules may have something to do with this. Let me break-down what I have, and what I want to achieve:
1. My router is setup with VLAN1 (172.16.1.0/24) as the inside zone (in-zone), while my outside zone (out-zone) is FastEthernet4 (DHCP WAN Interface). I also have a guest zone (guest-zone) VLAN12 (192.168.12.0/24) used for my guest SSID wireless, which is NATed to the outside zone.
2. I have my EasyVPN setup using a Virtual Template Interface that terminates at the WAN interface FastEthernet4 (something tells me this should be changed). Should I terminate at VLAN1, or an interface or loopback on VLAN1?
3. I ultimately want the VPN users to be able to conenct to the local resources on VLAN1 only, while being able to get out to the internet. [code]
View 14 Replies
View Related
Feb 23, 2011
is it possible to setup a Cisco ISR 881W so it connects to a Cisco ASA 5500 series head via network extension mode? We did this in the past with our PIX connecting to 3000 series concentrator.
View 1 Replies
View Related
Aug 10, 2011
i'm currently trying to configure a AP801AGN-E-K9 sitting within a 892W router.it was working previously with the following config, i just don't find it!
service-module wlan-ap 0 bootimage unified
interface Loopback0ip vrf forwarding XXXip address XX.XX.XX.XX 255.255.255.255
!interface wlan-ap0description Service module interface to manage the embedded APip vrf forwarding XXXip unnumbered Loopback0arp timeout 0! interface Wlan-GigabitEthernet0description Internal switch interface connecting to the embedded APswitchport mode trunkip vrf forwarding XXX
Logging into AP and its outputs:
telnet Lo0's-IP-ADDR 2002 /vrf XXX
OUTPUT:
AP6400.f1ce.b5ba#sh ip int brieInterface IP-Address OK? Method Status ProtocolGigabitEthernet0 unassigned YES DHCP up up
*Apr 18 19:52:56.959: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !! *Apr 18 19:53:06.959: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !! *Apr 18 19:53:16.959: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
guide me to a AP801AGN-E-K9 configuration manual in combination of 800 series routers..
View 1 Replies
View Related
Sep 15, 2011
I have a CUOM 2.3 and CUCM 7.0 installed, we are planned to have a major upgrade to CUCM to 8.5 soon, do i need to upgrade my CUOM ,since CUOM is a Network management system? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license? Is OM 2.3 to 8.X is a direct upgrade?
View 3 Replies
View Related
May 16, 2012
My Customer today have CUOM 2.3 and CUCM 7.1.3. He is planning to do upgrade CUOM 8.6 and CUCM 8.6. My question is: Is it possible to do upgrade CUOM directly to 8.6? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license?
View 4 Replies
View Related
Jun 30, 2012
How to install IP base liecense and Unified communication liecense in 2921 router?
View 1 Replies
View Related
Oct 20, 2012
I've got a LAN set up with a server and printer, no internet connectivity to it. When I need to access the internet, I connect through a wireless hotspot. The only problem is that I have to unplug the ethernet from my LAN connection for the wireless to work.Is there a way to have both connections coexist, so that when I need to print something or access a file on my server I can do so without it interfering with my internet connection?
View 4 Replies
View Related
Oct 21, 2007
I have an AIR-LAP1242AG-A-K9. Straight out of the box I thought it would have the GUI functional but this is not the case. I am brand new to Cisco products so it is taking me a while to get use to them and to TelNet but from what I have read in about 6 different manuals none have explained how I can access the configure terminal command when It doesn't show up. I am in privileged mode with access of: AP001c.588e.a266#show privilege. Current privilege level is 15.If I can't get into global configuration mode I cant enable the GUI, turn on the wireless.
View 6 Replies
View Related
Oct 30, 2012
Received Error:Object "Dot11BandSelect" does not exist. when configuring the 802.11 settings on a 4400 WLC runing ver. 6.0.196.0
View 1 Replies
View Related
Jun 16, 2012
How to connect my Windows XP Desktop to my homes wireless network system (my comp is outdated I know ). I have no trouble with my my mum's Windows 7 Laptop and no problems with my MacBook Pro, but how do I connect this old clunky XP to it?
Wireless Connections doesn't exist in my network connections tab, and in Services under Admin Tool - in the 'Wireless Zero Configuration Properties' is set to Automatic startup type and it is 'started'.
View 1 Replies
View Related
Nov 19, 2012
EA4500 router setting currently I am on an single fix IPs network, Internet access filtering by a Fortigate gateway, some IPs has Internet access, most of the IPs without, and we like to keep it that way.may I know what is the proper way to configure the newly added EA4500 router to working with "Guest Access" and my existing fix IPs network?
View 9 Replies
View Related
Jan 24, 2011
I've got a Cisco 881W Router and I am trying to set up the wireless Network. I've managed to get the SSIDs up and running, but I can't see to get DHCP addresses going from the router to the access point and Laptops .When i am connecting laptop directly to Router ethernet port i am able browse and seeing DHCP address. [code]
View 7 Replies
View Related
Sep 27, 2012
I'm putting together a design for a new office with the following requirements:
10 VPN users.For Ethernet – 24 ports POE 10/100/1000
Probably go with VZ FIOS so EthernetAbout 2000 square feet so 2 WAP's should do it I'm thinking a CISCO881W-GN-A-K9 ISR with a SRW224G4P-K9-NA switch should do the trick. This will give me an integrated AP but I need a second one. Do I need to order an autonomous one or does the 881W do some sort of WLC function?
View 1 Replies
View Related
Dec 8, 2012
-Model : TL-WR1043ND
-Hardware Version : v1
-Firmware Version : 120605
I'm wondering if USB HDD spin down capability does exist on the deviceI think this enhancement will be serve a lot of costumers who wish to use all USB features.
View 1 Replies
View Related
Jun 14, 2012
Access Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies
View Related
Dec 8, 2010
Is the max wireless speed on the cisco 881w 54mbps even though it has 802.11n hardware? What about the 891w ?
View 13 Replies
View Related
Jul 7, 2011
The 801 AP on my 881W reboots every other day or so, randomly, on its own. The router / AP works great otherwise, no other issues. I checked the error log and I see no indications of why it would be doing this.
ap#sh ver
Cisco IOS Software, AP801 Software (AP801-K9W7-M), Version 12.4(25d)JA, RELEASE SOFTWARE (fc1)
[Code]......
View 30 Replies
View Related
May 21, 2013
How to upgrade the IOS of the Integrated wireless AP in a Cisco 881W using TFTP server (I do have software)Router side is not an issue it is the integrated AP that gives problem?
View 14 Replies
View Related
Feb 2, 2012
I have a Cisco 881W configured for wireless (just a PSK, nothing special). I can get out to the Internet OK and browse to everywhere except my own websites.
It runs on a connection that does not connect directly to my network, but our website is available to the world externally.
Now, from the router a traceroute and ping work fine to our website but from the wireless connection I can get to everywhere else on the web but our website. A traceroute just stars out. I'm using 8.8.8.8 as a DNS server and nslookup resolves the DNS.
I can't set a DNS server or domain server on the ap on the 881W so are there any commands I can use to see what's going on?
View 2 Replies
View Related
Jan 17, 2011
Just recently got a new 881W router. i have downloaded the 2.4 software upgrade. I go into the Office extend AP login and i get just a enter button. when i click on the enter button the AP page does not come up.
View 7 Replies
View Related
Mar 30, 2013
1 router 881w with a site-to-site VPN connected to a switch and a wireless which allows internal users to access the VPN via wireless (this is like a backup, if the switch fails, then they can use the wireless). Everything's working fine so far. Now I want to configure a second WLAN for guest but I'm not really sure if this configuration will work:
ROUTER:
ip dhcp excluded-address 192.168.100.1 192.168.100.200
!
ip dhcp pool GuestNetwork
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
dns-server 8.8.8.8
[code]....
If it's not clear I want that everyone that is connected to the guest WIFI receives an IP address from the range I wrote before and then goes directly to the internet.
View 11 Replies
View Related
May 9, 2013
We've had a Cisco 881W set up in one of our remote offices for a while and the wireless has been fine. Yesterday I got a call saying that the wireless was no longer working.
I went over and it's true, the SSID is no longer broadcasting. I reloaded the router but it's still the same. I tried to get access to the embedded ap and I get this
RTR#service-module wlan-ap 0 session
% telnet connections not permitted from this terminal
RTR#
Now I've not changed anything on the configuration since it went in and it was working before. Has the embedded ap died? The embedded ap is still showing as a component in show hardware.
View 15 Replies
View Related
Oct 15, 2012
I recently purchased a new Cisco 881w router (last Friday).I have configured the 'wired' part of the router with little trouble, but the wireless side is proving a little challenging.I have read a number of posts complaining about the firmware version installed on my device being very buggy.The version of the firmware on the wired part is: Version 15.0(1)M8, however, the firmware on the wireless side seems to be: Version 12.4(21a)JA1 - the version reported as buggy. The former has a version date of 2012, with the latter being 2009.I have tried to download a newer version, but the site is asking me to provide a support contract.I wouldn't mind buying a support contract if the thing worked in the first place and I was trying to add some feature after it had been working for a while.
View 1 Replies
View Related
Oct 10, 2011
We had setup a wired/wireless LAN using Cisco 881W router for one of our client. Wired lan works OK but we have issues with wireless. Users on wireless LAN can connect to the wireless network, but cannot browse the Internet. The wifi network does not give out an ip address to the client so client cannot get to the default gateway and Internet. Not sure what part of config does not work.
##### sh runn #####
881WiFi#sh run
Building configuration...
[Code].....
View 10 Replies
View Related
May 9, 2012
I have a Cisco 881W and I would like to basically some how bridge the Cisco router to my netgear router. This is what I'm trying to achieve:
Cable Modem ----> Netgear Router ~~~~~ via wifi ~~~~> Cisco 881W ------> FastEthernet Ports
I've tried setting the Cisco 881W with station-role non-root with the SSID of my netgear router, but I get the error %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response whenever I try to bridge it.
Is bridging the Cisco router via wifi to the Netgear Router something that is not possible or is it an error on my part?
View 2 Replies
View Related
Nov 9, 2012
I have an integrated 881W with a built in 801 access point. I'm interested in increasing the range of my AP. I'm interested in considering any configuration changes while still maintaining support for N. I've included a copy of my running config.As well, I've heard of high gain antennas. I'm using the default antennas that came with the 881W. If there are better antennas that I can buy to increase my range, I'm interested in considering that as well.
View 10 Replies
View Related
Aug 19, 2010
I was trying to upgrade the IOS image of the AP and I did a wrong manip.
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.
View 4 Replies
View Related
Dec 18, 2011
I have a Cisco 881W that will no longer boot/operate properly if the internal radio card is installed. If the card is installed, all I get is the following...
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 2009 by cisco Systems, Inc
[Code]....
if I do a dev I get nothing. If I do a dir flash: I get "bad device name". My cookie shows FF in all positions.
If I remove the entire WiFi Radio card (both boards), then It boots fine, cookie appears intact, devs appear, IOS loads, just without the WAP.
Any chance this is a matter of a file getting deleted or corrupted or is this certainly bad hardware? The router sans Wifi appears fully functional.
View 2 Replies
View Related
Mar 19, 2012
I simply need to recover an embeded access point password.
I have the passwords to the 881-w router, but passwords to the embedded access point I don't have.
What is the recovery process for it, or the password reset process for the embedded access point.
View 8 Replies
View Related
Apr 28, 2013
a have a router CISCO 1841 and I configured a NAT inside from the router to the firewall like this :ip nat inside source static firewall_adresse public_adresse and its work fine and when a added it I do this command "wr" to save the configuration and I restarted the router many times and it still work fine,but in the last five months this NAT does not exsit twice and I must add it a gain.
View 7 Replies
View Related
Jan 6, 2012
Is there a limitation to the amount of sub-interfaces that can exist on a Cisco 6509? The switch has WS-SUP720-3B (Sup card), WS-X6724-SFP (linecard), and 12.2(33)SXH7 (IOS).
View 7 Replies
View Related
Apr 27, 2012
Everyone speaks about video and music streaming, however I am under the understanding that there isint actually any such thing as legitimate real time streaming, ALL files are saved to the disk or the RAM. If this was not the case, disrupting your Internet connection would cause an instantaneous crash of the streaming media, and well, I have had my Internet crash a lot of times while viewing streaming median and in every case it continued to play for some time.
View 5 Replies
View Related
