Cisco Wireless :: Upgrade IOS Of Integrated AP In 881W?

May 21, 2013

How to upgrade the IOS of the Integrated wireless AP in a Cisco 881W using TFTP server (I do have software)Router side is not an issue it is the integrated AP that gives problem?

View 14 Replies


ADVERTISEMENT

Cisco Wireless :: Increase Coverage For AP801 (integrated 881W)?

Nov 9, 2012

I have an integrated 881W with a built in 801 access point.  I'm interested in increasing the range of my AP.  I'm interested in considering any configuration changes while still maintaining support for N.  I've included a copy of my running config.As well, I've heard of high gain antennas.  I'm using the default antennas that came with the 881W.  If there are better antennas that I can buy to increase my range, I'm interested in considering that as well. 

View 10 Replies View Related

Cisco Wireless :: WLC Integrated 3750 Upgrade DHCP Failure

Jul 20, 2011

I've been working with a client's integrated 3750 WLC running 4.0.179.11. I want to upgrade the code because it is old plus I am having DHCP trouble.  I have a couple of questions:
 
1. Is it OK to upgrade to SWLC3750K9-5-2-193-0.aes ? or do I need to go through 4.2 first ?
2. Will that code upgrade the bootloader at the same time?
3. How can I make sure there is enough flash space on the WLC?
4. Are there any special considerations to plan/prepare for?
 
The DHCP issue is failure of associated clients to get an IP address with this message found in WLC debugging:

[Code]...

View 10 Replies View Related

Cisco WAN :: 881w Wireless Firmware Upgrade Required

Oct 15, 2012

I recently purchased a new Cisco 881w router (last Friday).I have configured the 'wired' part of the router with little trouble, but the wireless side is proving a little challenging.I have read a number of posts complaining about the firmware version installed on my device being very buggy.The version of the firmware on the wired part is: Version 15.0(1)M8, however, the firmware on the wireless side seems to be: Version 12.4(21a)JA1 - the version reported as buggy. The former has a version date of 2012, with the latter being 2009.I have tried to download a newer version, but the site is asking me to provide a support contract.I wouldn't mind buying a support contract if the thing worked in the first place and I was trying to add some feature after it had been working for a while.

View 1 Replies View Related

Cisco WAN :: 881W Not Able To Set Up A Wireless Connection

Jan 24, 2011

I've got a Cisco 881W Router and I am trying to set up the wireless Network. I've managed to get the SSIDs up and running, but I can't see to get DHCP addresses going from the router to the access point and Laptops .When i am connecting laptop directly to Router ethernet port i am able browse and seeing DHCP address. [code]

View 7 Replies View Related

Cisco Wireless :: Options For 881W ISR?

Sep 27, 2012

I'm putting together a design for a new office with the following requirements:

10 VPN users.For Ethernet – 24 ports POE 10/100/1000 

Probably go with VZ FIOS so EthernetAbout 2000 square feet so 2 WAP's should do it I'm thinking a CISCO881W-GN-A-K9 ISR with a SRW224G4P-K9-NA switch should do the trick. This will give me an integrated AP but I need a second one. Do I need to order an autonomous one or does the 881W do some sort of WLC function?

View 1 Replies View Related

Cisco Wireless :: 881W To Know Maximum Wi-Fi Speed

Dec 8, 2010

Is the max wireless speed on the cisco 881w 54mbps even though it has 802.11n hardware?  What about the 891w ?

View 13 Replies View Related

Cisco Wireless :: 881W - AP Random Reboot?

Jul 7, 2011

The 801 AP on my 881W reboots every other day or so, randomly, on its own.  The router / AP works great otherwise, no other issues.  I checked the error log and I see no indications of why it would be doing this.   
 
ap#sh ver
Cisco IOS Software, AP801 Software (AP801-K9W7-M), Version 12.4(25d)JA, RELEASE SOFTWARE (fc1)

[Code]......

View 30 Replies View Related

Cisco Wireless :: 881W Can't Set DNS Or Domain Server On AP

Feb 2, 2012

I have a Cisco 881W configured for wireless (just a PSK, nothing special). I can get out to the Internet OK and browse to everywhere except my own websites.
 
It runs on a connection that does not connect directly to my network, but our website is available to the world externally.
 
Now, from the router a traceroute and ping work fine to our website but from the wireless connection I can get to everywhere else on the web but our website. A traceroute just stars out. I'm using 8.8.8.8 as a DNS server and nslookup resolves the DNS.
 
I can't set a DNS server or domain server on the ap on the 881W so are there any commands I can use to see what's going on?

View 2 Replies View Related

Cisco Wireless :: 881W Office Extend Ap Login?

Jan 17, 2011

Just recently got a new 881W router. i have downloaded the 2.4 software upgrade. I go into the Office extend AP login and i get just a enter button. when i click on the enter button the AP page does not come up.

View 7 Replies View Related

Cisco Wireless :: 881w / Configure A Second WLAN For Guest?

Mar 30, 2013

1 router 881w with a site-to-site VPN connected to a switch and a wireless which allows internal users to access the VPN via wireless (this is like a backup, if the switch fails, then they can use the wireless). Everything's working fine so far. Now I want to configure a second WLAN for guest but I'm not really sure if this configuration will work:
 
ROUTER:
 
ip dhcp excluded-address 192.168.100.1 192.168.100.200
!
ip dhcp pool GuestNetwork
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
dns-server 8.8.8.8

[code]....
 
If it's not clear I want that everyone that is connected to the guest WIFI receives an IP address from the range I wrote before and then goes directly to the internet.

View 11 Replies View Related

Cisco Wireless :: 881W No Longer Broadcasting SSID?

May 9, 2013

We've had a Cisco 881W set up in one of our remote offices for a while and the wireless has been fine. Yesterday I got a call saying that the wireless was no longer working.
 
I went over and it's true, the SSID is no longer broadcasting. I reloaded the router but it's still the same. I tried to get access to the embedded ap and I get this
 
RTR#service-module wlan-ap 0 session
% telnet connections not permitted from this terminal
RTR#
 
Now I've not changed anything on the configuration since it went in and it was working before. Has the embedded ap died? The embedded ap is still showing as a component in show hardware.

View 15 Replies View Related

Cisco Wireless :: 881W - Wi-Fi User Cannot Reach Internet

Oct 10, 2011

We had setup a wired/wireless LAN using Cisco 881W router for one of our client. Wired lan works OK but we have issues with wireless. Users on wireless LAN can connect to the wireless network, but cannot browse the Internet. The wifi network does not give out an ip address to the client so client cannot get to the default gateway and Internet. Not sure what part of config does not work.
 
##### sh runn #####
881WiFi#sh run
Building configuration...

[Code].....

View 10 Replies View Related

Cisco Wireless :: 881W - How To Bridge With Netgear Router

May 9, 2012

I have a Cisco 881W and I would like to basically some how bridge the Cisco router to my netgear router. This is what I'm trying to achieve:
 
Cable Modem ----> Netgear Router ~~~~~ via wifi ~~~~> Cisco 881W ------> FastEthernet Ports
 
I've tried setting the Cisco 881W with station-role non-root with the SSID of my netgear router, but I get the error %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response whenever I try to bridge it.
 
Is bridging the Cisco router via wifi to the Netgear Router something that is not possible or is it an error on my part?

View 2 Replies View Related

Cisco Wireless :: 2504 Controller / 1602E - External Or Integrated Antenna For Better Coverage

Mar 24, 2013

I'm planning to use these with a 2504 controller.  However, I cannot find a straight answer on whether or not the External Antennas provide better coverage than the Integrated Antennas?  These will be wall mounted in a combo office/warehouse environment.  Also, I cannot figure out if the External Antennas are even included with the 1602E (AIR-CAP1602E-A-K9)?  or what if any power adapter/ injector is included with the AP's?

View 14 Replies View Related

Cisco Wireless :: 881W - Unified Setup / Bootimage Does Not Exist?

Feb 20, 2012

I'm setting up a couple 881W cisco routers to use Unified wireless and am running into a bit of a brick wall.I've read through the "Upgrading to Unified Cisco Software" section of the following article:[URL]The problem is, I can't run the "service-module wlan-ap0 bootimage unified" command. The keyword "bootimage" does not exist. The router is licensed for advipservices and I'm running version 15.0(1)M4 on the router. AP is currently running version 12.4(21a)JA1. why the bootimage command doesn't appear? Will I need to downgrade the router IOS to 12.4?Additionally I'm having trouble finding an answer to the following:Is there a way to set up the embedded AP on the same network as the Data VLAN on the router, or do I need to create a separate IP network for the embedded AP? I've tried using 'ip unnumbered vlan10' (vlan10 is the data vlan) on the wlan-ap0 interface but then when I try opening a session to the AP it doesn't connect.
 
bcp4n51001#service-module wlan-ap0 session
Trying 10.199.62.1, 2002 ...
% Connection timed out; remote host not responding
 
This is my Vlan10 setup for one of the routers:
 
interface Vlan10
ip address 10.199.62.1 255.255.255.0
ip helper-address 10.151.103.254
ip helper-address 10.150.1.254
ip pim sparse-mode

View 8 Replies View Related

Cisco Wireless :: Converting 881W From LWAPP To Autonomous Mode

Aug 19, 2010

I was trying to upgrade the IOS image of the AP and I did a wrong manip.
 
I downloaded the IOS image (ap801-rcvk9w8-tar.124-10b.JA3.tar) from my TFTP server to the flash of the AP. Everything went find so far. But than I did an archive archive download-sw /overwrite ap801-rcvk9w8-tar.124-10b.JA3.tar and my AP reboot in LWAPP mode.
 
I should have done: archive download-sw /overwrite tftp://10.0.0.1/ ap801-rcvk9w8-tar.124-10b.JA3.tar instead!
 
Now I don't how to go back to autonomous mode. archive commando is not available anymore in LWAPP mode.

View 4 Replies View Related

Dell :: Latitude D600 Wireless - Broadcom 570x Gigabit Integrated Controller

Oct 13, 2012

I recently got a Dell Latitude D600. I know, it's outdated. I'm running Windows XP SP3.

My problem is that after installing all of the drivers for the Broadcom 570x Gigabit Intergrated Controller, I can't get the wireless to pop up in the bottom right hand corner. I can only connect with an Ethernet cable directly from my router. I have tried many things, even support packages, but I can't seem to get it to work. I've also tried Fn+F2. Also, in the Device Manager I see a "Network Controller" but it has a question mark that is yellow beside it, and I can't seem to install it.

View 3 Replies View Related

Cisco Wireless :: 881W Will No Longer Boot With Radio Card Installed

Dec 18, 2011

I have a Cisco 881W that will no longer boot/operate properly if the internal radio card is installed. If the card is installed, all I get is the following...
 
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 2009 by cisco Systems, Inc

[Code]....
 
if I do a dev I get nothing. If I do a dir flash: I get "bad device name". My cookie shows FF in all positions.
 
If I remove the entire WiFi Radio card (both boards), then It boots fine, cookie appears intact, devs appear, IOS loads, just without the WAP.
 
Any chance this is a matter of a file getting deleted or corrupted or is this certainly bad hardware? The router sans Wifi appears fully functional.

View 2 Replies View Related

Cisco Wireless :: Recovering Embedded Access Point 881w Password

Mar 19, 2012

I simply need to recover an embeded access point password.
 
I have the passwords to the 881-w router, but passwords to the embedded access point I don't have.
 
What is the recovery process for it, or the password reset process for the embedded access point.

View 8 Replies View Related

Wireless :: How To Connect Via Integrated Wireless LAN

Mar 16, 2011

My Fujitsu Amilo L7310 has Integrated Wireless LAN. How do i set up a new connection? do I need to plug it in?

View 1 Replies View Related

How To Set Up Integrated 3G WWAN On HP2510p

Sep 2, 2012

I can't get the internal 3G modem on my HP2510p with Windows 7 Professional 32 bit working. So far I've downloaded and installed the following:-

HP Broadand Wireless Modules - Sierra Wireless Inc
HP Connection Manager - Hewlett Packard
HP Wireless Assistant - Hewlett Packard
Qualcomm Gobi Driver Package for HP - QUALCOMM

but it's still saying 'no dial tone' and not reading that it has a 3G modem. If I've downloaded anything, how I can uninstall it.

View 1 Replies View Related

Cisco Switching/Routing :: 891W-AGN-A-K9 / How To Get Integrated PoE

Feb 26, 2012

I have a client that that is installing a new network.  They have requested the use of an CISCO891W-AGN-A-K9 mostly to be consistent with upgrades perfomed at other sites.  I agree with the use of this router, so that's OK.  The issue is that they have requested that I use the integrated PoE available on this model.  I'm also OK with this as it will make a much neater installation.  However, I can't seem to find much information on how to get the integrated PoE.  I need clarification as to whether I can get a kit to upgrade this router.  I generally purchase from sites like newegg or cdw (I'm an independent contractor) and I can't seem to find one with it.  I have found some information on 800-IL-PM-4 and 800-ILPM-4 (who could confuse those ).  Are they the same or different?  Which one is the correct one and does it include the AC power adapter and can if be retro'ed into a router without the PoE?

View 2 Replies View Related

Cisco WAN :: ASR1001 / What Is An Integrated Daughter Card

Oct 1, 2012

I was doing some research on the Cisco ASR1001 model Router and within the description on the official Cisco page it mentions having various models that come with an "Integrated Daughter Card" or "IDC". I was curious as to what the IDC is exactly, considering there is an ASR1001 model without it.

View 2 Replies View Related

Cisco Switching/Routing :: C3850 With Integrated WLC

Jun 1, 2013

I have 3850 switch with integrated WLC and i wonder if i can access the WLC via GUI ,also i need to know if it support Dynamic vlan assignment over SSID.

View 2 Replies View Related

Cisco AAA/Identity/Nac :: ASR9K Integrated With ACS 3.3 Equipment

Jun 2, 2013

I am currently deploying Cisco ASR9K BNG solution and it needs to be integrated with a Cisco ACS 3.3 (yes that old .. going to migrate to new product in the future) equipment. There are several specific attributes need that are not on the base config of the ACS 3.3 but it seems that i can configure them manually:In addition to supporting a set of predefined RADIUS vendors and vendor-specific attributes (VSAs), Cisco Secure ACS supports RADIUS vendors and VSAs that you define. Vendors you add must be IETF-compliant; therefore, all VSAs that you add must be sub-attributes of IETF RADIUS attribute number 26..This is from the ACS 3.3 configuration manual.I have never done this user defined VSAs.

View 1 Replies View Related

Networking With Integrated 10 / 100 / 1000Base - T And PRO / 100VE

Mar 28, 2011

I have two desktop PCs connected via PRO/100VE LAN and am about to replace one of these with a desktop that has Integrated 10/100/1000Base-T. Will the two machines be able to communicate? One machine will use XP Home and the new machine Windows 7.

View 2 Replies View Related

Does Modem Have An Integrated Routing Feature

Mar 12, 2011

What I am trying to do is port forward certain ports so the servers I'm trying to run will allow other people to connect.So far I got no where since I got a new ISP. They can't provide any assistance since I use a netgear router. One of their tech support said their modem has a built in router. The rest all said no. I noticed that the IP in CMD when I type ipconfig /all is 192.168.1.(15-47) it switches every now and then. But that is a local IP. Wouldn't that single that the modem is already routing the IP? When I put my router on it switches to 10.0.0.(2-55). These are all local IP's though. Does the modem have an integrated routing feature? Verizon really sucks so far. They can't answer their own questions without conflicting with each other.

The modem is getting the IP, and putting it into a local IP (What I believe is a routing feature) for the network. Now the local IP goes to the netgear wireless router, and gets routed again (Changed the local IP to 10.0.0.?). The netgear only got a Local IP the first time however, so the external IP is not being... worked with in the netgear router. It is trying to port forward for the local IP address, which already works for me obviously, however it is not a WAN IP address and therefore no one else is able to connect to any of my servers.And lastly, verizon states they have only "Modems" and "Wireless routers" so if they have no modems that doesn't come with this feature, then I need to learn how to port forward while the IP is being routed twice, similarly to when you have two routers hooked into each other.

View 4 Replies View Related

Dell :: Vostro 220 Integrated NIC Dies

Apr 10, 2009

Bought a Vostro 220S about 2 months ago.  After about three weeks, while I'm using it, the integrated NIC dies.  All of a sudden I get the "Network Cable Disconnected" pop-up.  No LEDs lit by the network jack.  Contact Dell support who decides it's the motherboard.Three days later, the exact same failure.  Contact support again.  This time they want me to re-install Windows (yeah...right).  I refused since the motherboard fixed it the first time.  They finally agree to replace the motherboard again. Using the same router and cable that worked for years with my old computer.  After the first failure, I switched ports on the router.  While waiting for the motherboard replacements, I had installed an old PCI NIC I had laying around.  Worked fine...still is. I'm not about to re-install Windows, which is what I know they'll want.  I'll stick with the PCI card.  Both of the people at Dell support as well as the tech they sent out told me they've not seen this before.

View 6 Replies View Related

Dell :: XPS 210 Integrated NIC Blown By Lightning

Jul 19, 2012

there was a very close lightning strike near my house and my DELL XPS 210 accessed the router before but not after. Noother elctronics, even my 2 other DELL computers were affected. I've eliminated the NIC cables, router port,  everything but the actual NIC card. But diagnostics say it's working properly. Could a registry entry have been corrupted (I have a registry backup the day before). Can I replace the Integrated NIC with an internal (or external) NIC? I'm running XP Professional SP3.

View 3 Replies View Related

Cisco WAN :: Connect Integrated FastEthernet Ports On 2921/k9 To ISP

Jun 26, 2012

I am getting the new Cisco 2921/K9 router, which comes by default with 3 Integrated 10/100/1000 Ethernet ports. I have Comcast Cable as the ISP, so can I connect the ISP RJ45 Copper cable directly to one of the integrated ports or do I have to buy another WAN Interface Cards for the ISP.

View 3 Replies View Related

Cisco VPN :: 3005 / Windows 7 - Integrated Client Firewall

Dec 28, 2011

I try to connect from my Windows 7 32bit PC with CISCO VPN Client (5.0.07.0410) to a CISCO Concentrator 3005.
 
Initializing the connection using certificate "xxx"
Contacting the security gateway at x.x.x.x...
Negotiating security policies...
Securing communications channel...
Secure VPN Connection terminated by Peer.
Reason 435: Firewall Policy Mismatch.
 
Connection terminated on: Dez 28, 2011 18:06:56        Duration: 0 day(s), 00:00.00
Not connected.
 
The client did not match the firewall policy configured on the central site VPN device.  Cisco Systems Integrated Client Firewall should be enabled or installed on your computer.
 
Log on CISCO Concentrator:
 
32284 12/28/2011 18:06:56.620 SEV=5 IKE/141 RPT=40 x.x.x.x
Client-reported firewall does not match configured firewall: terminating tunnel.
Received -- Vendor: (0), Product (0), Caps: 0000.  Expected -- Vendor: Cisco Sy
stems(1), Product: Cisco Integrated Client(0x00000001), Caps: 0002
 
32287 12/28/2011 18:06:56.740 SEV=5 IKE/194 RPT=8064 80.153.72.120
Group [xxx]
Sending IKE Delete With Reason message: Firewall Parameter Mismatch.
 
The strange thing is, that I don't have any problems with the same CISCO VPN Client on a Windows Vista PC:
 
32755 12/28/2011 19:04:24.540 SEV=6 IKE/143 RPT=6612 x.x.x.x
Processing firewall record. Vendor: Cisco Systems(1), Product: Cisco Integrated
Client(1), Caps: 0002, Version Number: 0.0.0.0, Version String:

View 2 Replies View Related

Cisco WAN :: IP Multicast On 881W?

Dec 17, 2010

I am implementing mGRE with DMVPN so multicast traffic can be delivered to employee homes over Internet, everything worked fine except that I can not configure PIM or ICMP static groups on C881W's mGRE tunnel interface or BVI interface(RIPv2 works on mGRE interface however), configuring "ip multicast-routing" did not give me any errors, do I need license to be about to configure PIM/IGMP? I am running C880data-universalk9.mz.124-20.T5.bin" with license level advsecurity.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved