Cisco Wireless :: AP801AGN-E-K9 Unified Image On 892W Router?
Aug 10, 2011
i'm currently trying to configure a AP801AGN-E-K9 sitting within a 892W router.it was working previously with the following config, i just don't find it!
service-module wlan-ap 0 bootimage unified
interface Loopback0ip vrf forwarding XXXip address XX.XX.XX.XX 255.255.255.255
!interface wlan-ap0description Service module interface to manage the embedded APip vrf forwarding XXXip unnumbered Loopback0arp timeout 0! interface Wlan-GigabitEthernet0description Internal switch interface connecting to the embedded APswitchport mode trunkip vrf forwarding XXX
Logging into AP and its outputs:
telnet Lo0's-IP-ADDR 2002 /vrf XXX
OUTPUT:
AP6400.f1ce.b5ba#sh ip int brieInterface IP-Address OK? Method Status ProtocolGigabitEthernet0 unassigned YES DHCP up up
*Apr 18 19:52:56.959: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !! *Apr 18 19:53:06.959: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !! *Apr 18 19:53:16.959: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
guide me to a AP801AGN-E-K9 configuration manual in combination of 800 series routers..
View 1 Replies
ADVERTISEMENT
Mar 27, 2013
I'm working on a 892W router.To close the session between the wireless device and the router's console, the command Control-Shift-6 x is required.The Issue is that this command is not working for me. I'm using a SuperPuTTY connecting tool.
View 7 Replies
View Related
Mar 7, 2013
If I enable both radio interfaces on new 892W with integrated access-point 801 the radio interfaces are reseting every 30 seconds. I have already tried different IOS version 12.x and 15.x on the router and the integrated ap. Also tried a a configuration from another 892W, which is working fine on the other router. Still same issue. If I disable one of the interfaces, doesn't matter which, the access point ist working fine.With both enabled log of the ap shows:
Mar 8 19:09:26.403 MEZ: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Mar 8 19:09:27.583 MEZ: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
Mar 8 19:09:28.175 MEZ: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
Mar 8 19:09:28.203 MEZ: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
[code]....
View 1 Replies
View Related
Feb 20, 2012
I'm setting up a couple 881W cisco routers to use Unified wireless and am running into a bit of a brick wall.I've read through the "Upgrading to Unified Cisco Software" section of the following article:[URL]The problem is, I can't run the "service-module wlan-ap0 bootimage unified" command. The keyword "bootimage" does not exist. The router is licensed for advipservices and I'm running version 15.0(1)M4 on the router. AP is currently running version 12.4(21a)JA1. why the bootimage command doesn't appear? Will I need to downgrade the router IOS to 12.4?Additionally I'm having trouble finding an answer to the following:Is there a way to set up the embedded AP on the same network as the Data VLAN on the router, or do I need to create a separate IP network for the embedded AP? I've tried using 'ip unnumbered vlan10' (vlan10 is the data vlan) on the wlan-ap0 interface but then when I try opening a session to the AP it doesn't connect.
bcp4n51001#service-module wlan-ap0 session
Trying 10.199.62.1, 2002 ...
% Connection timed out; remote host not responding
This is my Vlan10 setup for one of the routers:
interface Vlan10
ip address 10.199.62.1 255.255.255.0
ip helper-address 10.151.103.254
ip helper-address 10.150.1.254
ip pim sparse-mode
View 8 Replies
View Related
Dec 26, 2012
I have a strange error in Cisco CISCO892W-AGN-E-K9 that i bought for our clients a month back.
- the router doesn't display the SSID for a longer period. Its like on and off of the SSID, showing sometimes and sometimes blank for the same device (Laptop/ Mobile/ or other Wireless Devices) within the range.
The router is in my office, but sometimes my laptop is connected, and sometimes it does not connect, and it is same with my other friends laptop.
Is it a problem with the device, configuration or the IOS issues?
View 4 Replies
View Related
Sep 15, 2011
I have a CUOM 2.3 and CUCM 7.0 installed, we are planned to have a major upgrade to CUCM to 8.5 soon, do i need to upgrade my CUOM ,since CUOM is a Network management system? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license? Is OM 2.3 to 8.X is a direct upgrade?
View 3 Replies
View Related
May 16, 2012
My Customer today have CUOM 2.3 and CUCM 7.1.3. He is planning to do upgrade CUOM 8.6 and CUCM 8.6. My question is: Is it possible to do upgrade CUOM directly to 8.6? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license?
View 4 Replies
View Related
Feb 14, 2012
I own a Cisco 892W router. The router has 2 WAN ports and 8 switch ports. Now I know -
-WAN ports can create sub interfaces, assigne IPs, cannot be assigned to a VLAN - sounds very much like a routing port. (sh interface gives - Hardware is PQII_PRO_UEC)
-Switch ports are for VLAN assignment, trunking, IP assigment etc,. (sh interface gives Hardware is Fast Ethernet)
I know they are different but at the same time confuced what the difference are? I also know on some 3xxx series switchs you could say "no switchport" and translate a switch port to a layer 3 port. But on 892W you can't do this? Struggeling to understand the difference.
View 4 Replies
View Related
Jun 30, 2012
How to install IP base liecense and Unified communication liecense in 2921 router?
View 1 Replies
View Related
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
Sep 19, 2012
I was using a wrt54gh which is no longer in working condition.. so i bought an E1200.the problem i face is when i try to restore my new router which is the E1200 frm the backup file frm my previous router the wrt54gh which is saved in my computer i get the error message " THE IMAGE FILE IS INCORRECT ".
View 4 Replies
View Related
Feb 3, 2013
I had originally set up my E1200 Jan 2012 & had Cisco Connect setup. I didn't use it much but back in Oct after being away for 10 days I didn't have internet connection. Had to re-set both cable modem--then I at least had connection via ethernet, but still no wifi connection. Had to turn off for awhile to get it Router to properly reset & work. & then I think I had to do another reset maybe in Dec, can't remember exactly.
As I mention in another post, I have been having frequent intermittent not connected to internet messages for a long time. Usually if I just turn wifi off & then turn it back on it finds my network (although frequently I notice that it was on my guest network rather than main). I still don't know if it is cable modem, router or my ISP, altho they came out & checked & said signals ok, but modem could be going (Its old but about to move so don't want to buy new modem now).
I updated to Mountain Lion about 2-3 weeks ago.After a Panic last night I was advised to make sure everything updated including router firmware.When I opened Cisco Connect it said I had an unsupported Operating System. Trying to figure this all out, I finally found links to download Cisco Connect that are supposed to be compatible w Mountain Lion (at least the original link said that, but not where I went w the links so hoping it is right link for that). Anyway I downloaded it & was reading a bit & then clicket on the setup icon.
That said it was damaged & to eject it. I downloaded it via wifi just like I download other software. Maybe it is hyper sensitive so I need to take it over to plug directly into my cable modem? But then that will mess up the router, although I guess it will need to be reset any way.So I think i need to get Cisco Connect updated so it works w Mountain Lion. Mountain Lion told me about 1 software that wasn't compatible but didn't pick up on Cisco Connect.So don't know if I need to do a hard wired download, unlike the way I download other things, or what to get an undamaged copy. I then hope that it will see the old version, even though it isn't didn't work & hopefully pick up all my settings & all.
& then I guess I still need to check for a firmware update. & I understand that a firmware update should be done w a good connection (although the user manual just says good signal, web says hard wired ethernet. & because of the intermittent issues I plan to to it manually by 1st downloading & then installing from the download so there won't be a risk of interruption during install--if its even needed.
View 6 Replies
View Related
Apr 14, 2013
I had download the last version firmware 10.0.19 WAG54G2 but its in img format and my notebook dont have CD drive anyway to unpack it ??
View 3 Replies
View Related
Feb 18, 2011
I`m having problem with booting Cisco router 2610 and I`m having this message :
C2600 platform with 131072 Kbytes of main memory
Program load complete, entry point: 0x80008000, size 0x439138
Self decompressing the image :####################################################################################################################################################################[OK]
After that, I can't type any thing?
View 3 Replies
View Related
Nov 27, 2011
I've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
View 1 Replies
View Related
Nov 4, 2012
last month I bought in our China office a 2811c router.I asked (to a Chinese informatic company) a router to create a IPSEC - site to site VPN connection with an ASA.I'm not in China, and when they told me that router was power on, I tried to configure VPN.It was a bomb when I found that the image installed was "c2800nmc-spservicesk9-mz.150-1.M7.bin" not enough for my VPN, we need for example "c2800nmc-advipservicesk9-mz.150-1.M7.bin".Is it possible that in China this image is forbidden for VPN political restriction? - If I can, what's the Cisco procedure to change ios image? I must to buy an advanced license or I only register and download which image I need?
View 5 Replies
View Related
Jun 12, 2011
imagine IOS image required size lists:DRAM 256 / 64 Flash
Then show ver on my router 3825 lists the below. Technically speaking the below should have the 64M flash required right? Why again it shows as 62592K and not 64000K?
View 1 Replies
View Related
Mar 11, 2012
I am sitting on Internet and want to copy IOS Image to router. I can SCP, itu authenticated to Router but ends with a message "host is not communicating for more than 15 seconds".
Router : Cisco 2821
Current IOS: (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1.
View 3 Replies
View Related
Jun 19, 2012
I have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies
View Related
Oct 3, 2012
I have Cisco 2600 series Router which has only 32 MB flash memory. I tried to load IOS image in that but image size is 29 Mb in compressed form. The minimum i found is 5 MB in compressed form but it is missing so many commands. that in 32 MB flash, how can I load image which has almost all the commands.
View 3 Replies
View Related
Feb 26, 2013
I recently formatted the flash drive of an 1800 router and replaced it with an updated image. However, the new features within the new image aren't reflected in the router. I believe that this is because a reboot would be required for the updates in the new image to be reflected in the router i.e. the image needs to be added to the system. How to get the image to the system without a reboot and if by doing so I would get all the new features from the image.For example, the show version below shows the old image in the system as [code]
View 2 Replies
View Related
Jan 8, 2012
Customer has ordered the following routers, which will go in three separate locations.
1. 3945 W/SPE150, IP Base Image
2. 3945 Voice Bundle, includes PVDM3-64 and (1) 2-port T1 MFT
3. 2911 IP Base Image.
If the customer wants to move the Voice image from the existing 3945 to the 3945/WSPE150, would he just need to contact Cisco Licensing, or would the customer have to pay for a software upgrade on the 3945/WSPE150?
Same scenario, except moving the Voice Image to the 2911 router.
View 5 Replies
View Related
Jan 12, 2013
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies
View Related
Jun 10, 2012
whether a Cisco Router 2911 would work on images other than universal image. This is the question raised by one of our customer. He has 2811 Router where-in he has configured T1/E1 configuration, terminated to Zyxel Modem and working fine. Now he wants to replace this 2811 router with 2911 router. Since the universal image in 2911 router is not working with the present configuration in 2811 router, he wants to know, what options are there for him to configure this in 2911.
View 2 Replies
View Related
May 8, 2012
I successfully converted an old 1231G to CAPWAPP. However, when I try to join it to a WLC5508 I receive the floowing errors. [code]
View 2 Replies
View Related
Oct 22, 2012
I struggle with how to install an IOS into an AP. And I am still not very clear on how this is to be accomplished. I have an 881W and have downloaded what I believe to be the latest IOS for this AP (ap801-k9w7-tar.152-2.JA). Problem is that I have not really found a good or at least clear set of instructions in how to load this IOS into my AP, so I have not done that yet.Does the IOS that is currently installed into the AP remain after an update or does the new IOS overwrite the current IOS. And how does one recover from a, heaven forbid, faulty installation. What is the fallback from that. How I can update my AP. Because, right now, I am most certainly hesitant to even attempt an upgrade.
View 4 Replies
View Related
Nov 3, 2012
i have cisco 1260 Access point with standalone ios ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?
View 1 Replies
View Related
Nov 29, 2012
I am trying to TFTP an image to a Cisco 2504 WLC. The management interface is 10.1.1.1 /24 and I have my PC connected to a port on the WLC with the IP address 10.1.1.10. However, I still do not have connectivity between the PC and WLC.
View 3 Replies
View Related
Dec 22, 2012
I purchased a used AIR BR1310G-A--K9-R from a local high school that was rebuilding their athletic field. The AP was used for communications for their pressbox staff. The AIR BR1310G was part of the schools campus wide WiFi network and was upgraded to an lwapp image c1310-k9w8-m 12.4 3c JA. Our home sits on a large lot and I would like to convert the BR1310G back to an autonomous AP.
In order convert it back to an automonous AP, I will need the original image. The school used a contractor for their WiFi network and they do not have a backup of the original image. I do not have a service account with Cisco so downloading the autonomous image from the Cisco website is out. What are my options for either obtaining an image file or using the current managed image without a WLC?
View 0 Replies
View Related
Feb 13, 2013
I have a couple 1130AG switches. I'm trying to pull an image file from the flash on a Cisco Air AP1131AG. The file is c1130-k9w8-mx.124-23c.JA4.tar. The issue that I'm seeing is, I do not see a copy command to go through the tftp process. I've tried to use tftpd32 and enter the IP of the AP as the remote host, but that is not working either. Do I need to connect an ethernet cable straight to the AP in order to use Tftpd32, or can I use a console cable?
View 9 Replies
View Related
Apr 1, 2013
% CDP is not supported on this interface, or for this encapsulation*Apr 2 18:35:20: %CAPWAP-3-ERRORLOG: capwap ifs: read error or timeout
[code]....
View 12 Replies
View Related
Apr 5, 2012
Any IOS image for the Aironet 1310? May I have a copy of it. I cant access to Cisco support today.
- C1310-k9w7-tar.124-25d.JA1.tar
- C1310-k9w7-tar.124-21a.JY.tar
View 2 Replies
View Related
