I was using a wrt54gh which is no longer in working condition.. so i bought an E1200.the problem i face is when i try to restore my new router which is the E1200 frm the backup file frm my previous router the wrt54gh which is saved in my computer i get the error message " THE IMAGE FILE IS INCORRECT ".
View 4 Replies
I have downloaded the firmware update "Ver.1.0.02 build 11" for my WRT400N from linksys.com several times. I then try to update my firmware on my router. Each time I try, I get an error message that says "Incorrect file path."
View 9 Replies View RelatedI had download the last version firmware 10.0.19 WAG54G2 but its in img format and my notebook dont have CD drive anyway to unpack it ??
View 3 Replies View RelatedI'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatedI was upgrading the FW to 2.07 and after waiting 180 seconds, the router didn't came back, I reset the router and now got a Firmware Upgrade System Ver 1.0.0.2 Date 2009/12/07 Screen when typing 192.168.0.1. Tried to upload all the firmwares starting with 2.00NA and always got the Incorrect hardware ID image, please Check! message.. I can't get the *D-Link Router Recovery Mode* page or any other page. Looks like the firmware update wasn't successful and the router is not longing working, need to find out how to recover from a faulty firmware installation.? Also I open a case with DLink Tech Support, they told me to call Tech Support but I can't access the numbers from my country. I already answered their email like 4 times that I can't access the # and they keep telling me to call the #. Anyway what else I can do to recover the Router.
View 9 Replies View RelatedI have Windows 7 Home Premium on a Dell Inspiron N5010.
I have had this problem for several weeks, and have searched all over to find a solution (tried them all, but none have fixed it). I have a good wireless internet connection, and sometimes I use ethernet. Despite having such connections, my wireless internet icon doesn't change, as it seems to keep getting stuck on the icon which shows a red x over the ethernet image.
It will show the blue loading ring with the bars as it searches for a wireless connection for a little bit, but then it goes to the same, incorrect icon, even though when I put the cursor over the icon it says "Internet Access".
So far, I've tried deleting the Icon Cache and rebooting, as it was suggested that it could be potentially corrupted, but the internet icon stays the same. I have also tried searching for a driver that could be potentially related to the issue and uninstalling it, but it didn't work. The red x went away for a moment, being replaced by a loading blue ring, but then the red x returned (same icon image).
Is there a specific driver for the icon itself? I know I had to uninstall a driver then reboot to get my battery icon back after it mysteriously disappeared. I also have tried deactivating/reactivating my wireless connection by hitting the button, but it doesn't change.
I don't know how to access the router now to reset my system. My wired computer works fine. I have used this router without issue for several years. I used windows Xp and now I installed windows 7. After that i cannot connect to the router. I tried with 192.168.1.1 in my browser and with the setup CD. I just cant enter to setup the router. On the other computer the internet is functioning perfectly. I use the same cable, so the problem is not in the cables.
View 4 Replies View RelatedFirmware version is V1.0.01 b001 my WRT54GH has recently started to shuts off periodicaly without any reason. Will stay off for couple of minutes, then will turn ON again. In this period, On/OFF button has no effect.
View 4 Replies View RelatedI need to set the local IP for my new wrt54gh wireless router to 172.28.2.x & netmask to 255.255.0.0 but there is no option to set the netmask to 255.255.0.0 in the drop down menu / list .
View 5 Replies View Related1st time use cisco router.Where to check the list of user connecting to the router?
View 6 Replies View Relatedhave problem with WRT54GH, almost every second page after reload gets an error message: Error 101 (net::ERR_CONNECTION_RESET): The connection was reset. Tried both on IE, Firefox, Chrome Tried to disable antivirus, no effect, the pages still load not all the time, firmware upgraded to the latest version. Before didi not have such problem with Zyxel W330EE.
View 4 Replies View RelatedI'm not able to logon to WRT54GH-SG over 192.168.1.1. I'm using correct password & have NOT forgotten. I'm hitting 401 page. The support rep told me reset the router which I do not want to before I explore any possibilities.
View 8 Replies View RelatedI have linksys WRT54GH wireless router with me.I want to know how can i connect it with any other wireless router. What settings do i need to change.
View 1 Replies View RelatedI've updated latest firmware & installed 5 pieces of WRT54GH at our building. Then I noticed each of them disappear from wireless connections list and IP scan list (no ping response). If they might not response to pings but they serve as switch without any problem, I mean there are no wired connection problems, they work as switch all the time. The problems are -again-
1-) Wireless lost and / or 2-) Ping response lost
Turning them off and on again will fix them. But I'm tired of bosses who complain about their faulty pc connectivity.
Don't they run 7/24? I tried to restart them on every 12 hours programmatically/remotely but it couldn't work.
Ive been using this router for about 4 months now. suddenly it wont let me connect wirelessly through itouch nor through imac. it says Unable to join the network "linksys" eventhough "linksys" is indicated to be an available WIFI network and that signal is full. Problem is still the same even after i reset the router a couple of times pass 30seconds, set the security to No Password.if i connect the router with a cable it connects seamlessly and allows me to go online.
View 8 Replies View RelatedI have a linksys WRT54GH wireless router running firmware v1.0.01 build 001.It's setup with DHCP.My desktop computer is connected to the router via cable.I also access the connection using my laptop, via wireless.The problem is that after I start using the desktop (wired connection), I can't connect from the laptop using wireless. It happens every time. I then turn the router off and back on again. After this procedure I can successfully connect from both the desktop (wired) and laptop (wireless).
View 6 Replies View RelatedI purchased WRT54GH wireless router back in 2009 and it was working fine except for past 1 month, wherein the Internet Connection was being disrupted 15 - 20 times in an hour. I thought it could be fault from ISP end; however after investigation by ISP we found the fault was not from ISP as, when Wireless was unable to establish connection with the DSL Modem it was failing but when tried to connect laptop with the DSL Modem it worked fine (Wired connection). I did try the Settings mentioned in an earlier post to change the UPnP and the Beacon Interval etc. This however doesnot seem to work as the internet has been disconnected almost thrice since then. (Approx. 15 - 20 mins). When the router is unable to connect to internet I restart the Wireless Router and the DSL Modem. After restarting, the Internet connectivity works fine.
Below are the Advanced Wireless Settings from Wireless Tab:
Authentication Type: Auto Shared (Default: Auto)
Basic Rate: Default (Default: Default)
Transmission Rate Auto (Default: Auto)
CTS Protection Mode: Disabled Auto (Default: Auto)
--------------------------------------------------------------------------------
Beacon Interval: (Default: 100 Msec, Range: 20 ~ 1000)
DTIM Interval: (Default: 1, Range: 1 ~ 255)
Fragmentation Threshold: (Default: 2346, Range: 256 ~ 2346)
RTS Threshold: (Default: 2347, Range: 0 ~ 2347)
I just bought WRT54GH router. I have one PC (running Ubuntu) connected via Wireless.Every 5-10 minutes I get disconnected for a short period of time (about 10-30 seconds). During that period I am able to access router configuration page, but can't connect to the "outer" world... Surely it's not about my Internet provider, since connecting the PC directly to the Internet cable works fine with no "disconnections".
View 9 Replies View RelatedMy router (WRT54GH) doesnt seem to be enabling the wi-fi network. Non of my devices are able to detect the wireless network.
View 1 Replies View RelatedMy router (WRT54GH) doesn't seem to be enabling the wi-fi network. Non of my devices are able to detect the wireless network.
View 3 Replies View RelatedI'm interested how to enable or use the "SpeedBurst" option on Linksys WRT54GH router?
View 1 Replies View RelatedAnyone has a register of problems between a router WRT54GH and A495 telefone of Siemens?I mean they can be working in the same frequency, that´s why in some rooms I can connect my wireless network very well.
View 1 Replies View Relatedi am a using a WRT54GH linksys router.. which was working fine for a year.. there was thunderstorm and lightning a few days back.. since then my routers internet port (the first port which says internet in yellow) has stopped working..
View 5 Replies View RelatedI just installed WRT54GH and wireless was working fine, after almost 3 hours passed I lost connection with it.I tried to connect using wireless with 3 different notebooks without success. Just using cable it works.I upgraded firmware from v1.0.010 to v1.0.01 but still not working.
View 7 Replies View RelatedI have a WRT54gh, and the signal strength is extremely poor. Full strength at about 15 centimeters, Then drops to 50% at 50 centimeters. By 1.5 meters, the signal is extremely weak or not visible. Have updated to the latest firmware, factory reset and power cycled. There are no other wireless networks or devices that would provide interference Have experimented with channels, thresholds, transmit type, encrypted/open, intervals etc..No luck. Due to signal dropping off so quickly it seems like a transmit strength issue rather than an issue that can be solved in the menu. I'm wondering if there's a way I can console log-in to the Linux kernel and check the transmit strength and perhaps bump it up by a few DB? It's out of warranty so a solution involving opening the case is also acceptable.
View 9 Replies View RelatedI have a question regarding cisco aironet 1240ag AP.
1st - Does this devices has a firmware ? So I can update a firmware ? or is an image file for IOS software ?
2nd - Which wireless controller I can use to handle multiple aironet 1240ag AP's ?
3rd - The controller has the ability to create temporally guest password ?
I received a Linksys E1200 from a friend who careless tried to upload an incorrect configuration. After that the device became use full. It don't work at all.
View 1 Replies View RelatedThe smart wi-fi app Device List indicates Local Network = 0 (that's incorrect) and Guest Network = 0 (that's correct). When i click Connected Devices for My Network, i see a list of devices but everything indicates 'Offline' and that of course is incorrect.How can i upgrade this software? I recently installed EA6500 and due to being slow, it was recommended to set back to factory default. That process did no go well, so i hope it is not necessary again. This router is not any better then the wrt320N so i am disappointed.
View 7 Replies View RelatedI have several devices connected to my Linksys EA4500. Two of them are my Apple Mac Pro and my Logitech Squeezebox Radio. For some reason, in 'Device List', my Apple Mac Pro has the manufacturer 'Logitech' and the model 'Squeezebox Radio'. As for my Logitech Squeezebox Radio, it doesn't have a manufacturer nor a model. It appears that there is a mix up with these two devices. I have cross checked the IP addresses and MAC addresses displayed in Cisco Connect Cloud with those displayed on the devices and they match - so it's not a case of mixed up names. Could this be an issue with Cisco Connect Cloud?
View 1 Replies View RelatedI have a pix 515, time to time the firewall start rebooting with invalid flash error I found erasedisk.bin in internet, after that i cant load pix532.bin ios file and others pix***.bin are not workingThe only file i am able to load is pix508.bin it,s start asking me activatin number before install I have a previous activation number ios version 5.3.2 but this number is not correct.
View 1 Replies View RelatedI've been trying to configure this Cisco ASA 5505 for days now. I used to be able to use the ASDM gui application, but i've since transitioned into using the CLI. Trying to go back to ASDM, it won't let me get back in, and when i try show asdm image, it says Device Manager image file not set. I have no CD for this device and I need that image file for the ASDM. How can I locate the file and install it on the router so I can use it?
View 2 Replies View Relatedi recently bought a new Supervisor Engine 720 WS-SUP720-3B and 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF. Once i fired it all up i got this error %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 2, power not allowed: Unknown Card Type. the System image file is "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXE6a.bin".
I have a 6509 up and running the same mods and working fine BUT the System image file is sup-bootdisk:s72033-ipservicesk9-mz.122-18.SXF7.bin. Is the boot image what is causing my isses?
I am doing image upgrade on Catalyst 6509-E. During TFTP image transfer to sup-bootflash I always see !!!!!!!!!!!!!!!!!o!!!!!!!!!! "o" out of sequence packet. Although the image size seems to be correct at the end but there is always some "o" packets.
I am assuming not, but I haven't tried loading with the image after seeing this.
