I just installed WRT54GH and wireless was working fine, after almost 3 hours passed I lost connection with it.I tried to connect using wireless with 3 different notebooks without success. Just using cable it works.I upgraded firmware from v1.0.010 to v1.0.01 but still not working.
View 7 RepliesI have a linksys WRT54GH wireless router running firmware v1.0.01 build 001.It's setup with DHCP.My desktop computer is connected to the router via cable.I also access the connection using my laptop, via wireless.The problem is that after I start using the desktop (wired connection), I can't connect from the laptop using wireless. It happens every time. I then turn the router off and back on again. After this procedure I can successfully connect from both the desktop (wired) and laptop (wireless).
View 6 Replies View RelatedI have linksys WRT54GH wireless router with me.I want to know how can i connect it with any other wireless router. What settings do i need to change.
View 1 Replies View RelatedI am currently at a friends house attempting to fix a situation he is having with his' wireless router, it is a Linksys WRT150n.Connection to the internet is possible via ethernet connectivity, however wireless is another story, devices can see the network but cannot connect to it, i have disabled the security key from the network to see if it was a simple password incorrection but still no dice.The current basic wireless settings have network mode set to mixed, and radio band, wide and standard channels set to auto, all other settings in the advanced tab are set to their default values.
View 1 Replies View RelatedI have an internet dvd player that can only connect through a wired connection but my router (verizon wi-fi modem) is located in another room.I was wondering how I can wirelessly connect my old router (e2000) to the one in another room? Would I configure it as a access point?
View 6 Replies View RelatedMy WRT54G router locks up 100% of the time when attempting to connect connect wirelessly to a Samsung Blue Player (Model number BD-P3600). I can connect to it with a cable no problem, but when I attempt to do so wirelessly and type in the password on the Blue Ray player, it attempts to connect but the router locks up and all devices connected to it (wired or wirless) lose connectivity
View 1 Replies View RelatedI get a great wired connection but when I try for wireless the Samsung says I have a great connection, except when I try to use the Apps from the Blu Ray it tells me, No Internect Conncetion. Samusung support tells me I need to "open the ports" on my E3000 and make the Blu Ray a priority...I don't know how to do that.
View 7 Replies View RelatedRunning Win XP (no service pack), WPA personal. Two other computers connect fine. On an old laptop running Win XP the network card sees the router, but when I enter the correct passcode (16 character) I get a message saying the code must be 13 characters. How can a connect this computer without disabling the other two wireless devices running through the router?
View 2 Replies View RelatedI have a BEFW11SF V4 firmware version 1.52.03. I just bought an HP DJ3051A and can't get it to connect. HP support says I need to change a setting to mixed mode but I don't see that I can. Does this router supports mixed mode and if so how do I change it?The other comment the HP rep made was the printer does not support Wireless N. I am fine with this since the router says Wireless B. It seems based on the HP rep's comment that as long as I am not using Wireless N, then I should be fine.
View 1 Replies View RelatedI have an original Xbox 360 (wifi not built in) and the external wifi adapter. With all previous Cisco routers, I have been able to connect my Xbox successfully and quickly. Now, however, I am experiencing much difficulty.
I have verified I am using the latest firmware for my router, and configured my router like this: [URL] in terms of ports. I have also used the Xbox's MAC address to give a static IP address via my router's DNS.
The Xbox can see both my main wireless SSID and my guest SSID but cannot connect to either.
I just hooked up my new Sony BDV-E570 Blu-ray home theater in a box. Everything looks great except it is not connecting to my WRT110 wireless router. Router is one level below where the home theater system is located, and signal strength appears good (4 bars) on the Blu-ray player, but it repeatedly says "connection failed" when I try to connect. The Wii is also in the same place and has no problems connecting wirelessly to the WRT110 router.
View 2 Replies View RelatedI purchased an E2500 wireless router. I am trying to replace a Netgear wilreless router with no success. During installation my laptop reaches about 25% and I get an error message. In short my laptop asks for an IP address with a password. Once I enter that information I receive an error message to call for assistance.
View 1 Replies View RelatedI don't know how to access the router now to reset my system. My wired computer works fine. I have used this router without issue for several years. I used windows Xp and now I installed windows 7. After that i cannot connect to the router. I tried with 192.168.1.1 in my browser and with the setup CD. I just cant enter to setup the router. On the other computer the internet is functioning perfectly. I use the same cable, so the problem is not in the cables.
View 4 Replies View RelatedFirmware version is V1.0.01 b001 my WRT54GH has recently started to shuts off periodicaly without any reason. Will stay off for couple of minutes, then will turn ON again. In this period, On/OFF button has no effect.
View 4 Replies View RelatedI need to set the local IP for my new wrt54gh wireless router to 172.28.2.x & netmask to 255.255.0.0 but there is no option to set the netmask to 255.255.0.0 in the drop down menu / list .
View 5 Replies View Related1st time use cisco router.Where to check the list of user connecting to the router?
View 6 Replies View Relatedhave problem with WRT54GH, almost every second page after reload gets an error message: Error 101 (net::ERR_CONNECTION_RESET): The connection was reset. Tried both on IE, Firefox, Chrome Tried to disable antivirus, no effect, the pages still load not all the time, firmware upgraded to the latest version. Before didi not have such problem with Zyxel W330EE.
View 4 Replies View RelatedI'm not able to logon to WRT54GH-SG over 192.168.1.1. I'm using correct password & have NOT forgotten. I'm hitting 401 page. The support rep told me reset the router which I do not want to before I explore any possibilities.
View 8 Replies View RelatedI've updated latest firmware & installed 5 pieces of WRT54GH at our building. Then I noticed each of them disappear from wireless connections list and IP scan list (no ping response). If they might not response to pings but they serve as switch without any problem, I mean there are no wired connection problems, they work as switch all the time. The problems are -again-
1-) Wireless lost and / or 2-) Ping response lost
Turning them off and on again will fix them. But I'm tired of bosses who complain about their faulty pc connectivity.
Don't they run 7/24? I tried to restart them on every 12 hours programmatically/remotely but it couldn't work.
Ive been using this router for about 4 months now. suddenly it wont let me connect wirelessly through itouch nor through imac. it says Unable to join the network "linksys" eventhough "linksys" is indicated to be an available WIFI network and that signal is full. Problem is still the same even after i reset the router a couple of times pass 30seconds, set the security to No Password.if i connect the router with a cable it connects seamlessly and allows me to go online.
View 8 Replies View RelatedI purchased WRT54GH wireless router back in 2009 and it was working fine except for past 1 month, wherein the Internet Connection was being disrupted 15 - 20 times in an hour. I thought it could be fault from ISP end; however after investigation by ISP we found the fault was not from ISP as, when Wireless was unable to establish connection with the DSL Modem it was failing but when tried to connect laptop with the DSL Modem it worked fine (Wired connection). I did try the Settings mentioned in an earlier post to change the UPnP and the Beacon Interval etc. This however doesnot seem to work as the internet has been disconnected almost thrice since then. (Approx. 15 - 20 mins). When the router is unable to connect to internet I restart the Wireless Router and the DSL Modem. After restarting, the Internet connectivity works fine.
Below are the Advanced Wireless Settings from Wireless Tab:
Authentication Type: Auto Shared (Default: Auto)
Basic Rate: Default (Default: Default)
Transmission Rate Auto (Default: Auto)
CTS Protection Mode: Disabled Auto (Default: Auto)
--------------------------------------------------------------------------------
Beacon Interval: (Default: 100 Msec, Range: 20 ~ 1000)
DTIM Interval: (Default: 1, Range: 1 ~ 255)
Fragmentation Threshold: (Default: 2346, Range: 256 ~ 2346)
RTS Threshold: (Default: 2347, Range: 0 ~ 2347)
I just bought WRT54GH router. I have one PC (running Ubuntu) connected via Wireless.Every 5-10 minutes I get disconnected for a short period of time (about 10-30 seconds). During that period I am able to access router configuration page, but can't connect to the "outer" world... Surely it's not about my Internet provider, since connecting the PC directly to the Internet cable works fine with no "disconnections".
View 9 Replies View RelatedMy router (WRT54GH) doesnt seem to be enabling the wi-fi network. Non of my devices are able to detect the wireless network.
View 1 Replies View RelatedI was using a wrt54gh which is no longer in working condition.. so i bought an E1200.the problem i face is when i try to restore my new router which is the E1200 frm the backup file frm my previous router the wrt54gh which is saved in my computer i get the error message " THE IMAGE FILE IS INCORRECT ".
View 4 Replies View RelatedMy router (WRT54GH) doesn't seem to be enabling the wi-fi network. Non of my devices are able to detect the wireless network.
View 3 Replies View RelatedI'm interested how to enable or use the "SpeedBurst" option on Linksys WRT54GH router?
View 1 Replies View RelatedAnyone has a register of problems between a router WRT54GH and A495 telefone of Siemens?I mean they can be working in the same frequency, that´s why in some rooms I can connect my wireless network very well.
View 1 Replies View Relatedi am a using a WRT54GH linksys router.. which was working fine for a year.. there was thunderstorm and lightning a few days back.. since then my routers internet port (the first port which says internet in yellow) has stopped working..
View 5 Replies View RelatedI have a WRT54gh, and the signal strength is extremely poor. Full strength at about 15 centimeters, Then drops to 50% at 50 centimeters. By 1.5 meters, the signal is extremely weak or not visible. Have updated to the latest firmware, factory reset and power cycled. There are no other wireless networks or devices that would provide interference Have experimented with channels, thresholds, transmit type, encrypted/open, intervals etc..No luck. Due to signal dropping off so quickly it seems like a transmit strength issue rather than an issue that can be solved in the menu. I'm wondering if there's a way I can console log-in to the Linux kernel and check the transmit strength and perhaps bump it up by a few DB? It's out of warranty so a solution involving opening the case is also acceptable.
View 9 Replies View RelatedI have a small home LAN of four hard-wired PCs and two iPads and two notebooks which are connected by wireless. At the heart of it all is a Linksys X3000 wireless router. Any of the four PCs that are hard wired to the X3000 have no problems talking to each other but none of the wireless-attached iPads or notebooks are able to see any other machine on the network. All machines are able to access the Internet.
View 9 Replies View RelatedI have an HP Pavilion desktop computer running Windows XP Home Edition. It used to never get internet wirelessly for some reason until one day i played around with it. I don't remember how but I got it to go online and it worked ever since. Just recently i have moved from my previous home and have finished setting up both of our computers. The Vista (the one i am using to write this) is an Ethernet connection and is having no problem connecting to the internet. Although, the XP for some reason will not connect to the internet. The adapter will find the network but when i type in the WPA2 it tries to connect but i think it times out or something. I have tried several solutions and none have worked. My father has a Toshiba laptop and he is currently having no issue with connectiong wirelessly to the internet. Our old verizon router stopped working when we attempted to set it up after the move, so verizon came and istalled a new one. It is secured with a WPA2 code whereas our older one was secured with a WEP code. I think it might be a problem with either the router or the wireless adapter itself (which is a Linksys Wireless-B Network Adapter). Also, when i logged into my router manager thing, I noticed that under the network, it said the XP was an inactive Ethernet Connection and not Wireless.
Here are some of the XP's specs:
Hewlett-Packard Pavilion
Intel[R] Pentium[R]
4 CPU
3.40 GHz
0.99 Gb of Ram
I have a network at home that me, my brother, and my parents share. I will be building my own PC and placing it in my room, which is upstairs. However, our router and modem are both downstairs. Now, my questions is, will that be a problem? As in, will my network bandwidth be bad? I really can't reconfigure my network nor can I have my computer downstairs since there is not enough room downstairs to place it. I also have a computer desk in my room from a few years back. The modem we have is 2700HG-B Gateway and the router is a CISCO Linksys one. I just have a miniUSB Wireless N adapter.
View 11 Replies View RelatedI have a Linksys X5000 hooked up with my home pc. The internet I get is free though the private school's network I work at (across the street) through a LAN. With a bit of wrestling I got my desktop to connect with the internet through the Linksys like an ethernet switch.I can't get my wireless devices to connect with the internet without logging in as a guest, which is annoying to do every time, especially through my iPod. They will gain access to my network, but not the internet.
Since this is a school network, my IT guy gave me a static IP address to speed up up/downloads by disabling DHCP. Every time I try to do that I get a message that "the page at 192.168.1.1 says the value can't be equal." OK, so I try to change my router's IP to 192.168.1.2 and...no luck, same message. I love working with hardware, but networking is beyond me. I don't think I can log into the guest screen in my own house any more! I am getting a new tablet in 2 days and this just won't do.