Cisco Wireless :: Pulling Image From 1130AG?
Feb 13, 2013
I have a couple 1130AG switches. I'm trying to pull an image file from the flash on a Cisco Air AP1131AG. The file is c1130-k9w8-mx.124-23c.JA4.tar. The issue that I'm seeing is, I do not see a copy command to go through the tftp process. I've tried to use tftpd32 and enter the IP of the AP as the remote host, but that is not working either. Do I need to connect an ethernet cable straight to the AP in order to use Tftpd32, or can I use a console cable?
View 9 Replies
ADVERTISEMENT
Mar 2, 2013
I have desktops hardwired to a switch, which is connected to my cable modem. They pull a 10.x.x.x ip address with DHCP. I have a wireless modem (e3200) connected to the cable modem. My wireless devices pull a 198.x.x.x ip address. Can connect to the internet just fine, BUT..Because of this (im assuming) I cannot add my printer to my wireless laptop. Different networks, wont connect via share name etc.So, if i turn off DHCP and NAT on the wireless router, shouldnt my laptop pull DHCP from the cable modem and get a 10.x.x.x IP address while connected wirelessly?My wired computers can connect to the shared printer just fine, only my wireless computers cannot. I have another printer that is networked (connected directly to the switch, no computer) with a static ip of 10.x.x.199. My laptop can connect and print to it just fine. I just cant connect to the printer that is attached to the 10.x.x.x computer.
View 3 Replies
View Related
May 28, 2012
My home is about 20 years old. I want to pull out all the old phone wiring and replace it with CAT-5 cabling. I have several questions.
1) Is it likely the phone cable is loose in the walls, or is it typically tied down inside the walls? Therefore, can I use the phone cable to pull the CAT-5 (unterminated)?
2) I heard that fire code construction demands that holes in the wall joists be filled - is that true?
3) Any least invasive way to get CAT-5 around my home? I can pull to only a select few spots if it's very difficult.
View 2 Replies
View Related
Jan 3, 2013
is there a way to pull the config file from this? I tried looking through console mode, but was not able to find an option for it. Or is it just not possible?
View 1 Replies
View Related
Mar 31, 2013
I have a Cisco SG 300 28 port switch that I have set in Layer 3 mode. I set up a second VLAN on it (vlan 4). I also set up the scope for DHCP on a Windows server for both VLAN's. The problem I am having, is that VLAN 4 is not pulling DHCP at all. The DHCP server is connected to port 1 on the switch, and the specifics are as follows:
VLAN 1: 192.168.5.251 subnet 255.255.255.0
VLAN 4: 192.168.55.251 subnet 255.255.255.0
DHCP Server 192.168.5.1
[Code]......
View 6 Replies
View Related
Feb 23, 2012
I have Broadband 100 from Shaw Cablesystems (100mbps speed).I can only pull 30mbps with the DIR-615. I have tried exchanging it for another one, same issue.Is there some kind of configuration option I'm missing?
View 14 Replies
View Related
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Aug 7, 2011
I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. [code] I found some details here: url... but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
View 3 Replies
View Related
Jun 19, 2012
Where is the link to download recovery IOS for AP1130AG.
View 4 Replies
View Related
Sep 4, 2012
Configuring a Cisco 1130 AP (autonomous) to a 1861 router.
I am struggling to work out how to connect this and get it working.
Router has 2 v lans, VOICE and DATA. All switch ports configured for access v lan (DATA) and voice v lan (VOICE)
We need the AP to have an SSID for VOICE and DATA and the gateway/DHCP server for each of these to be the router.
View 1 Replies
View Related
Oct 17, 2011
I got a problem with a ap that I have here where I do not have the password and I did the process to reset the AP to factory defaults, but the configuration still the same, and the AP still asking for the enable password, its the same problem poused before in this link URL. I did the same process but I still have the old configuration on the AP. I noticed that the AP change the image when I reset the AP, using the mode button. the AP is starting with and rcv image. I need to reset the AP to its initial configuration.
View 9 Replies
View Related
Oct 1, 2012
I'm trying to set up this 1130AG with a private wireless network and a guest wireless network. Initially it had just one wireless (private) and it worked fine, but then when I created the two VLANs for each SSID and then the guest SSID and now the guest SSID is visible/broadcasting, but the private SSID has disappeared or is off.
P.S. - It's a Cisco Aironet 1130AG (AIR-AP1131AG-A-K9) running 12.3(8)JEA system software and I'm using the web GUI (I'm not familar with the command line for Cisco products yet).
View 4 Replies
View Related
Feb 10, 2013
I have multiple cisco 1130ag access point at one of my clients villa. The issue I am facing is when moving throughout the buildingthe laptop and smartphones will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
For example, I start at one end of the building where it connects to AP#1 , if I then slowly go to another section of the villa, it it will not switch over to AP#2 until the signal is lost from AP1
I have following settings
AP's are Cisco 1130AG
Single SSID with WEP Security
View 9 Replies
View Related
Feb 17, 2013
i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
View 2 Replies
View Related
Oct 13, 2010
I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
View 3 Replies
View Related
Jul 27, 2012
One of my Wi-Fi site, having cisco_1130AG access points nearly 110nos as of now i installed 80nos, after installing, in out off 80nos nearly 12nos of APs's radio is showing down.
Again i reset and re-configure then it is working fine, is there any readio (802.11g/a) problem in this model?
View 5 Replies
View Related
Aug 16, 2012
I have 1 EuroDocsis modem and 2x 1130AG wireless things.How do I manage to get this connected to each other wirelessly?The internet is allready configured at the EuroDocsis modem and I now want to distribute it wirelessly to both 1130AG's. The EuroDocsis is using WPA2 PSK.I read something about WDS, but I don't get that to work either.
View 1 Replies
View Related
Jul 19, 2012
I have a Problem with a customer WLAN. The customer has a Aeronet 1130AG AP. Now i should configure a Aironet 1130 Repater for this WLAN. The initial connection from the Repater with the AP is no Problem. But after some time the Repeater lost the connection. On the AP i see following Messages:20Jul 19 19:05:28.061InformationInterface Dot11Radio0, Deauthenticating Station xxx Reason: Previous authentication no longer valid 21Jul 19 19:05:28.061WarningPacket to client xxx reached max retries, removing the client 22Jul 19 16:43:59.412InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx23Jul 19 16:43:57.901InformationInterface Dot11Radio0, Deauthenticating Station yyy 24Jul 19 16:43:56.536InformationInterface Dot11Radio0, Station yyy Associated to Parent xxx 25Jul 19 16:43:51.555InformationInterface Dot11Radio0, Station zzz Associated KEY_MGMT[WPA PSK] 26Jul 19 16:43:29.078InformationInterface Dot11Radio0, Station Repeater01 xxx Associated KEY_MGMT[WPA PSK]
View 2 Replies
View Related
Mar 23, 2011
We have a guest wireless network using 1130AG Access Points. Is it possible to allow devices on this network access to an Internal IP? I know that kind of defeats the purpose on the guest network, but we'd like to give access to internal email to these devices. Currently this does not work because you cannot loop back into the network to gain access (out the firewall and right back in the same port).
View 5 Replies
View Related
Feb 16, 2013
what are the series of access point that are supported without WLC. anteena should be in built and capability link 1130ag series.
View 9 Replies
View Related
Jan 20, 2010
The 1130ag was the LAP model but I upgraded it to run in autonomous mode. My understanding is that it cannot assign IP addresses but I just want that confirmed. It is not connected to a WLC nor a server that can do DHCP.
View 5 Replies
View Related
Mar 17, 2012
How can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies
View Related
Sep 15, 2010
we just deployed a cisco wireless solution with WLC4404-100, WCS, and a bunch of 1130AP and I experience some problem with file copy under windows xp. The file copy is working fine with my Ethernet connection however.The symptom is as follow. I cannot copy large file from a share to the computer. The copy starts then after a while (let's say 30MB copy over a 100MB file) it stops with the error 'File copy error: The network name is no longer available'. When this occurs, I still have my wireless card connected and I can ping my computer from the controller.I tried to adjust some radio settings (channel, power on the AP I'm connected to) because we have a large wireless network here, but no success. I also update the wireless card driver, create a new SSID, etc. No success at all. However the copy went fine for small file size.
View 9 Replies
View Related
Nov 12, 2012
Several 1130AG AP, auto IOS, are showing the same three errors;
1. 'Error' Interface BVI1 Changed to up
2. 'Error' Interface Fast Ethernet0 Changed to up
3. 'Error' Interface Dot11Radio0 Changed to up
ATTACHED image
Why these interfaces coming 'up' would be an 'error'? Seems almost like hardware failure/s. So we have been investigating on several 1130AGs bought from different places, with different configs and still get the errors. The APs appear to 'work' (i.e. basic config, wireless working, clients assoss., data flows to internet and back through APs) but the error causes the event log to show 'error' and for the status LED to turn 'yellow', instead of 'light green' (light green when working normally and no clients assos).
I have worked with many cisco APs and never ran across these two errors.
At first I thought it was a power issue, as the AP will boot up in low power if it doesnt think it's getting enough power, which could cause the IOS error possibly. But all of our APs are powered by wall plug cisco 48v OEM plugs, no POE injectors or switches. We even changed the settings in power of the IOS to 'pre-compatiable' POE and similar and still recieve the error and yellow LED status light. We looked into this power issue because we wanted to rule out if these was what was producing the errors that were reporting.
The second thing we did was setup the test APs with a very basic config, one ssid, no security, as to rule out a config error and also, no config will make the radios disabled, so without a basic config the APs cant be tested anyway (since the radios are now disabled from default). so we tested very basic configs and still getting the error and yellow LED (which all manuals say it should be light green normally working and no clients). all config changes brought wireless up and we can connect clients and data flows but still the errors stay and yellow LED once all clients disconnect. Note; when clients connect the yellow LED turns to light green, but thats not the colors the manual states they should be which is odd).
Third, a couple engineers suggested this error was from the AP scanning channels to choose the least congested (default config) and it will pick a channel but produce this error still and go yellow. We changed the configs to the least congested channels and it reboots and still gets these errors.
We have tried several IOS software packages, some newer, some older, all auto. though, no LAP.
We googled the errors but could only find ONE post with these errors. Some engineers said these errors are 'normal' and they have seen them before, but theres nothing on the web about the errors and we have owned 20-40 different cisco IOS APs and never seen this, and we have the same issues with 4 1130AGs, all in almost new condition, bought from different places.
Unless you have opened a 1130 many people dont know the status LED is actually 3 LEDs (one assembly with 3 micro LEDs, blue, green and red) that combine in color (the micro LEDs light up in different intensities causing many final color combintations), and the LEDs colors mix together via a plastic light guide on the top to show the status LED, and we believe the error is causing the status LED color to be off because the error is making the yellow light up and mix with the other colors causing all the other colors to be incorrect. we have researched trying to clear the error by 'clear logging' CLI command, hoping that may clear out the interface error and turn the yellow LED off because there would be no log of the error, but we have not succeded.
View 2 Replies
View Related
Aug 16, 2012
I can not get this to work.I have 1 EuroDocsis modem and 2x 1130AG wireless things.How do I manage to get this connected to each other wirelessly?The internet is allready configured at the EuroDocsis modem and I now want to distribute it wirelessly to both 1130AG's. The EuroDocsis is using WPA2 PSK.
View 3 Replies
View Related
Jun 1, 2012
I have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
View 5 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
Apr 27, 2012
I have 100 nos of cisco 1130AG access points and I upgraded the ios for one of the access point.
the existing image is c1130-k9w7-tar.124-21a.JA1
upgraded image c1130-k9w7-tar.124-25d.JA.
what is the advantage of upgrading the ios.and i want to upgrade the image to all the access points at time?
View 1 Replies
View Related
Feb 25, 2013
I'm trying to configure the 1130AG from scratch but I'm not having any luck. I tried using the IPSU utility and entered the MAC address but it errors, "The device does not answer". I have connected it to a network so it can get an IP from DHCP but it doesn't respond. And when it boots up from factory reset there is no SSID broadcast for me to connect to. I have tried connecting through the Ethernet port and the Console port to my computer but no luck.
View 3 Replies
View Related
Jul 10, 2011
I have two ssid's on my 1130ag each with different security when I use wep I can get my email on my droid. When i connect to the second ssid and use wpk I can get to the in the Internet but my email will not move in Exchange.
View 3 Replies
View Related
Jul 4, 2012
With this customer they have 4 floors with on each floor a Cisco Aironet 1130AG. At the moment they are using WEP as a protection with a really long key. The users find this annoying, but I am more concerned about the security perspective. So I want to implement WPA2 with a shorter key for the people to remember. On one floor, I also want to add a public network when other people want to connect and just need internet access. How to change the current set-up and regarding the security and implementation. If all of the Access Points could work togheter and just be 1 wireless network. I don't know if this is possible and how to do it? For the public network I know there also need to be some changes in VLAN's. The firewall is a cisco ASA5505.
At the moment I am running this configuration: I tried setting up this with the GUI, but it doesn't look like the configuration at the moment is shown in the GUI or maybe I am just looking in the wrong places. [code]
View 1 Replies
View Related
Jan 24, 2013
I am currently trying to get eap-tls user certificate based wireless authentication working. The mismatch of guides im trying to follow has me coming up trumps with success so far.
My steps for radius:- (i think this part ive actually got ok) [URL]
Steps for the wireless profile on a win 7 client:- this has me confused all over the place [URL]
My 1130 Config:-
[code]
Current configuration : 3805 bytes
!
! Last configuration change at 11:57:56 UTC Fri Jan 25 2013 by apd
[Code].....
View 14 Replies
View Related
Feb 12, 2013
How would I configure a "guest" wireless network, with a different key/password, that uses a different subnet than the existing network?
We have a simple 192.168.1.x subnet currently, with the Aironet as our only AP. The Aironet support a "guest" wireless function, but how do I make that work with the RV180?
View 1 Replies
View Related
