Pulling Configuration File From HP 2900-48G?
Jan 3, 2013is there a way to pull the config file from this? I tried looking through console mode, but was not able to find an option for it. Or is it just not possible?
View 1 Replies
ADVERTISEMENT
D-Link DIR-615 :: Configuration For Pulling Up 100mbps Speed?
Feb 23, 2012I have Broadband 100 from Shaw Cablesystems (100mbps speed).I can only pull 30mbps with the DIR-615. I have tried exchanging it for another one, same issue.Is there some kind of configuration option I'm missing?
View 14 Replies View RelatedCisco Switching/Routing :: How To Copy Configuration From 2900 Series To Another One
Oct 11, 2012I know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
Cisco VPN :: ISRG2 2900 - How To Count Number Of Cumulative VPNs On 2900
Aug 25, 2011If there is a router ISRG2 2900 with SEC license and without HSEC license, there is a limit in count of cumulative encrypted VPN tunnels of 225. Which commands can show us a number of current tunnels on the router, so we can see if we are near this limit of 225?
View 4 Replies View RelatedPulling CAT-5 With Phone Wire
May 28, 2012My home is about 20 years old. I want to pull out all the old phone wiring and replace it with CAT-5 cabling. I have several questions.
1) Is it likely the phone cable is loose in the walls, or is it typically tied down inside the walls? Therefore, can I use the phone cable to pull the CAT-5 (unterminated)?
2) I heard that fire code construction demands that holes in the wall joists be filled - is that true?
3) Any least invasive way to get CAT-5 around my home? I can pull to only a select few spots if it's very difficult.
Cisco Wireless :: Pulling Image From 1130AG?
Feb 13, 2013I have a couple 1130AG switches. I'm trying to pull an image file from the flash on a Cisco Air AP1131AG. The file is c1130-k9w8-mx.124-23c.JA4.tar. The issue that I'm seeing is, I do not see a copy command to go through the tftp process. I've tried to use tftpd32 and enter the IP of the AP as the remote host, but that is not working either. Do I need to connect an ethernet cable straight to the AP in order to use Tftpd32, or can I use a console cable?
View 9 Replies View RelatedPulling DHCP From Cable Modem Instead Of Wireless Router?
Mar 2, 2013I have desktops hardwired to a switch, which is connected to my cable modem. They pull a 10.x.x.x ip address with DHCP. I have a wireless modem (e3200) connected to the cable modem. My wireless devices pull a 198.x.x.x ip address. Can connect to the internet just fine, BUT..Because of this (im assuming) I cannot add my printer to my wireless laptop. Different networks, wont connect via share name etc.So, if i turn off DHCP and NAT on the wireless router, shouldnt my laptop pull DHCP from the cable modem and get a 10.x.x.x IP address while connected wirelessly?My wired computers can connect to the shared printer just fine, only my wireless computers cannot. I have another printer that is networked (connected directly to the switch, no computer) with a static ip of 10.x.x.199. My laptop can connect and print to it just fine. I just cant connect to the printer that is attached to the 10.x.x.x computer.
View 3 Replies View RelatedCisco Switching/Routing :: SG 300 VLAN Not Pulling DHCP?
Mar 31, 2013I have a Cisco SG 300 28 port switch that I have set in Layer 3 mode. I set up a second VLAN on it (vlan 4). I also set up the scope for DHCP on a Windows server for both VLAN's. The problem I am having, is that VLAN 4 is not pulling DHCP at all. The DHCP server is connected to port 1 on the switch, and the specifics are as follows:
VLAN 1: 192.168.5.251 subnet 255.255.255.0
VLAN 4: 192.168.55.251 subnet 255.255.255.0
DHCP Server 192.168.5.1
[Code]......
Cisco :: RME 4.2 Can't Get Configuration File From ASA5520
Aug 10, 2010I have a problem with RME 4.2 from CWLMS 3.1. I have configured SSH in my asa 5520 device but RME can't get the configuration file. I ran a job to sync archive but i get this message error:
*** Device Details for ASA_5520_VOZ_01 *** Protocol ==> Unknown / Not Applicable Selected Protocols with order ==> Telnet,TFTP,SSH Execution Result: CM0062 Polling ASA_5520_VOZ_01 for changes to configuration. CM00 Polling not supported on
[Code].....
Copying Configuration File To Usb Storage Device?
Jul 6, 2012How do i copy the configuration file from a switch to a storage device (USB)
View 1 Replies View RelatedD-Link DIR-655 :: What Is The Path Or File Name For Saved Configuration
Mar 15, 2011What is the name or path for the file stored on your hard drive for the configuration settings?
View 7 Replies View RelatedD-Link DIR-825 :: Possible To Load Configuration From Saved File
Nov 10, 2011Is it possible to load the configuration from a saved configuration file from a DIR-625 to a DIR-825? If so, what steps are required?
View 1 Replies View RelatedD-Link DIR-655 :: Restored Configuration File Has Been Uploaded In Failure
Mar 20, 2012I'm only able to restore my settings from a backup taken in July 2011. Any backups that I take, say today for example, won't restore. Any attempts to restore them is returned with "The restored configuration file has been uploaded in failure." I haven't changed my router. The firmware remains the same. I'm using Firefox, though I believe I've always used Firefox to interface with the router.
View 1 Replies View RelatedD-Link DIR-655 :: Router Configuration File Format Difference Between Rev A And Rev B
Mar 31, 2011I've owned the Rev A DIR-655 for years and have loved it, but recently it started acting up. I have a complicated setup saved as a gateway settings file (.gws). I decided to purchase a new DIR-655 for the ease of importing my settings without having to manually setup again, however, much to my dismay, the new file format for the configuration settings on the Rev B is not .gws but rather .bin. The .gws file will not import. I tried changing the file extension to .bin with hopes it might import but no luck. I also found the utility which decrypts the .gws file into .xml and used those values to manually re-enter the settings into the Rev B router, but my port forwarding is not working the same. I was wondering if there is any utility to convert the .gws file to the .bin file in order to import into the Rev B router, or if not, can I still purchase the Rev A model somewhere. The online shops I've checked do not list the hardware version.
View 7 Replies View RelatedCisco Wireless :: To Download Configuration File Of WLC 4400
Jul 22, 2006If already saved the configuration file of a WLC 4400 to a server using TFTP? What is the name of the configuration file?
View 2 Replies View RelatedCisco Security :: ASA5520 How To Remove Configuration File
Jul 15, 2007I want to put the asa5520 to the factory default please let me know how to do that. how to remove the configuration file from it.
View 5 Replies View RelatedCisco Routers :: RV082 V3 - View Configuration File?
Feb 27, 2013Currently, the backup config is not human readable...any way to convert this?
View 1 Replies View RelatedCisco WAN :: 2950 Switch Receive Configuration File From ISP?
Aug 28, 2012At home I have a perfectly working test setup for more than 1 year now , but yesterday we had a power down for about 10 minutes in the whole area , after this power down nothing was working in my network any longer.
My Network is has follow :
ISP(Cable Modem) on FA23 from the CISCO 2950 SWITCH (24 Ports)
ROUTER (ON A STICK) on FA24 from the CISCO 2950 SWITCH
And the rest of the switch is FA1=VLAN 1; FA2=VLAN 2;FA10=VLAN 10
Our home network is connected to VLAN 10 with a IP Range of 192.168.10.x /24 After this power down , I was not able to look into the SWITCH via FA1 , the FIX IP in this switch was 192.168.1.251/24, the ONLY way to get access was via the consol port !!!What a suprice when I connected my consol to the PC , I can see ROUTER_F342 , my router config is called ROUTER1841 and my switch config name is /was called SW24.So it seems that after this Power Down , the router took or received a config from my provider ?!?
I have recovered the the file in the switch + the vlan.dat and now everithing works again.
How can I avoid that this switch receive again a wrong file , I have all the needed files on the products itself and I do not use a TFTP server.
I have atached some screen shot when my switch is starting up , and it seems that the switch receive a IP address from my ISP , I do not know why, in the config file I have given it a FIX IP 192.168.1.251/24 ?!?So it seems that my ISP erase the config file and when the switch is empty ,the swich look for :
tftp://255.255.255.255/router-confg
tftp://255.255.255.255/ciscortr.cfg
Etc ....
Until it find something.
I have tried after a complete recovery to switch off the power again for 10 minutes (ISP MODEM + SWITCH + ROUTER) and I was not able to reproduce the fault.Can it be that due to this power failure in our area that some routers or switches send or broadcast this kind of things ?
Cisco :: Save Configuration File On 2960-48PST To FTP Server?
Feb 25, 2013I'm trying to save a configuration file on my 2960-48PST to a FTP server.
Unfortunately it doesn't work. What different steps I should follow ?
The software version is 12.2(50)SE5.
Cisco WAN :: 2811 / 2911 - Use Old Configuration File With New Model Directly?
Dec 11, 2012We have CISCO2811 model with VWIC2-2MFT-T1/E1 module working good over the E1 line. Since it's getting hard to find new model of CISCO2811 we decided to connect new branches with CISCO2911/K9 model (according to migration doc)
My question is can we use 2811's old config file with the 2911 model directly?
Cisco Switching/Routing :: C3750 - Running Configuration File
Aug 7, 2008We have a bunch of switches that are running fine but the running-config file is missing and we can't save the config to the tftp server. IOS is c3550-ipbasek9-mz.122-37.SE1. I've got lots of these switches running the same code that are just fine.
View 8 Replies View RelatedCisco Switches :: File Extension For Download Backup Configuration Sg300-10
May 7, 2012i want to download an backup of the configuration file of my Cisco sg300-10 but do not know what to call the file extension.. backup.??? backup.img? backup.ros ?
View 4 Replies View RelatedCisco Security :: 3310 - NAC Profiler - NetWatch Invalid Configuration File
Jul 18, 2010I'm trying to configure the NAC Profiler with a 3310 CAS Collector. In the "Edit Collector" menú, it shows all the modules as "Running", except for the NetWatch module which shows a state "Invalid configuration file (missingInternalAddress)".
I configured the eth3 interface of the CAS as a monitor interface in the Profiler (see attached image), and I tested that the SPANed traffic actually reaches that interface from the access switch. I'm using software version 3.1.0_24 in both the Profiler and the Collector.
Cisco Wireless :: How To Take Backup Of Configuration File For WLAN Controller 4420
Nov 4, 2012I need to take the backup of configuration file for WLAN Controller 4420, I tried all the possibilities given in the documentation but the backup fails, I have main confusion with the file name to be backedup, i am not able to findout the configuration filename any where even when i use CLI?
View 1 Replies View RelatedCisco Routers :: RV220W - DHCPv6 Prefix Delegation - Editing Configuration File?
Jan 25, 2012I am trying to configure this router to obtain an IPv6 address from my ISP who offers a dual stack IPv4/IPv6 DHCPv6 Prefix Delegation service.
I did a WAN packet capture to see the type of DHCPv6 packets the router sends to the ISP in order to obtain an IPv6 address and I saw that the router is sending DHCPv6 solicitation packets of type IA_NA i.e. for Identity Association for Non-temporary Address. However, most ISPs that offer a dual stack IP4/IPv6 service, they use DHCPv6 Prefix Delegation in which case the router is expected to send DHCPv6 solicitation packets of type IA_PD i.e. for Identity Association for Prefix Delegation.
I then downloaded its configuration file and saw the following:
dhcpv6c = {}
dhcpv6c[1] = {}
dhcpv6c[1]["renewTime"] = "3600"
[Code].....
So, the option for the DHCPv6 client to perform a prefixDelegation request is disabled. Does that mean that if I set this flag to "1" it is going to work? Well, I edited the configuration file and changed this flag but the router refuses to load it! It complains about the file being changed. How does it know that? Is it computing some type of checksum? How can I manually edit this flag and update the router's configuration?
Cisco WAN :: 1841 Router - HWIC Interface Card - Cannot See Interface In Configuration File
May 9, 2012i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View RelatedCannot Access File Because Another Process Has Locked Portion Of File
Jul 26, 2011I am working on a Drupal site which is on a virtual server (the way it's been explained to me). I've been told I need to work with it through webdev. So I can copy a file off the server and onto my local machine. I make my edits and then try to upload it to the server. I get locked out with the message: Error 0x80070021: The process cannot access the file because another process has locked a portion of the file. I have tried shutting down my code editor, opening and closing the connection, tried different methods of reaching the server (Cyberduck and through Window's map network feature) to no avail. What can I do?
View 1 Replies View RelatedCisco WAN :: PBR On 2900 Series For Ip Through Put
Feb 11, 2011I am looking for a Cisco document that gives me the,IP through-put on 2901, 2911 and 2921 routers with Policy based routing applied.,IOS version 15.1.3TOther processes, EIGRP Stub, VLAN routing, SRST,MGCP gateway (analog and PRI).
View 1 Replies View RelatedCisco WAN :: 2900 Nothing Appear For ACL Debug
Mar 22, 2012i have 3 access-list configured IN | Out on my Border router (MARTIAN) ,i have to look which one block some of the traffic passing through ,for that matter i have enabled the below commands on my ISR 2900: with nothing output.
View 3 Replies View RelatedCisco WAN :: Update IOS 15.2.2T For 2900?
Feb 23, 2012latest IOS version is from 18Nov11 and with little amount of traffic it keeps cpu usage sky-high until it starts losing packets (I've tried performance fine tuning according to cisco webpages and saw little difference)
Downgrading isn't an option as 15.2.1 version doesn't implement everything I need...
Cisco VPN :: 2900 - How To Get VPN Design
Nov 24, 2011Is GET VPN be a better choice than DMVPN in order to support VoIP, Video over IP, Advanced QoS and Multicast? I think it should be the better choice based on what is described as the benefits and how it works but I just want an expert opinion.
Can separate groups be created using the same key serves? I need to protect two functionally separate WAN segments that terminate on the same DC core routers. However I want the separate WAN segments to have different encryption policies. Is this possible?
It is stated in the deployment guide for GET VPN that "Network Address Translation (NAT) is not supported by GETVPN. NAT must be performed before encryption or after decryption when GET is used." However the NAT capability is required on all the routers.
The 2900 series routers has embedded hardware encryption but according to the router perfomance guide, with a mix of traffic such as NAT, QoS and IPSec VPN they are unable to provide 100 mbps of throughput. Does the new ISM VPN modules would allow the routers to achieve 100 mbps of throughput with the services mentioned above?
Printer Drivers For Canon 2900?
Jan 18, 2012Printer drivers for canon 2900?
View 1 Replies View RelatedCisco WAN :: MBTF For 2900 And 3900?
Jun 20, 2012provide my some (official) info regarding the MBTF for the C2900 and C3900 routers (2911 and 3945)? This info is currently not part of the data sheets.
View 0 Replies View Related