Cisco Security :: ASA5520 How To Remove Configuration File
Jul 15, 2007I want to put the asa5520 to the factory default please let me know how to do that. how to remove the configuration file from it.
View 5 Replies
ADVERTISEMENT
Cisco :: RME 4.2 Can't Get Configuration File From ASA5520
Aug 10, 2010I have a problem with RME 4.2 from CWLMS 3.1. I have configured SSH in my asa 5520 device but RME can't get the configuration file. I ran a job to sync archive but i get this message error:
*** Device Details for ASA_5520_VOZ_01 *** Protocol ==> Unknown / Not Applicable Selected Protocols with order ==> Telnet,TFTP,SSH Execution Result: CM0062 Polling ASA_5520_VOZ_01 for changes to configuration. CM00 Polling not supported on
[Code].....
Cisco Security :: Copying Configuration From PIX To ASA5520?
Aug 21, 2012i hav asa5520 i copying configuration from PIX to ASA5520 (7.2) everything working fine bt problem is that after sometime my DMZ interface losing connectivity ...
View 1 Replies View RelatedCisco Security :: 3310 - NAC Profiler - NetWatch Invalid Configuration File
Jul 18, 2010I'm trying to configure the NAC Profiler with a 3310 CAS Collector. In the "Edit Collector" menú, it shows all the modules as "Running", except for the NetWatch module which shows a state "Invalid configuration file (missingInternalAddress)".
I configured the eth3 interface of the CAS as a monitor interface in the Profiler (see attached image), and I tested that the SPANed traffic actually reaches that interface from the access switch. I'm using software version 3.1.0_24 in both the Profiler and the Collector.
Cisco WAN :: 3945 / How To Remove A File With SNMP From Router
Dec 10, 2012On a 3945 voicegateway,I want to remove a wave file (announcement), with the purpose that a new one can be automaticaly downloaden from UCCE to the box.Is there a way to do that automaticaly with SNMPSET <voicegateway> <MIB OID> <??wave file name??> <reload>
EDIT: or clear the cache, which it should be I think. (all wave file cache, or only one file, not sure what should be used and/or what is possible
Security / Firewalls :: How To Remove Constant Popups
Jun 22, 2011how to remove constant popups[CODE]
View 1 Replies View RelatedCisco WAN :: ASR1K 3.7.0 Unable To Remove Configuration
Sep 25, 2012When doing some tests with an ASR1K running 3.7.0.S, I noticed that everytimes I reload the router, I got the following error when it loads the configuration: [code]
View 1 Replies View RelatedCisco WAN :: To Remove Awkward Configuration 7206 Vxr
Jan 10, 2011ROUTER#sh run | i ip cefip cef table event-logip cefip cef accounting non-recursive load-balance-hash ip cef accounting non-recursive external
>snip<
ROUTER#conf tEnter configuration commands, one per line. End with CNTL/Z.ROUTER(config)#no ip cef accounting non-recursive load-balance-hashCommand authorization failed.
% Incomplete command.
ROUTER(config)#no ip cef accounting non-recursive load-balance-hash ?% Unrecognized commandROUTER(config)#^Z
cisco 7206VXR (NPE-G1) processor (C7200-JS-M), Version 12.3(10c)
How do I remove "ip cef accounting non-recursive load-balance-hash" from the config. I'd like to leave the box as I found it. Is it to do with an authority level or something more?
Cisco Security :: Remove License Previously Installed On ASA 5510?
Nov 15, 2010I'm currently reconfiguring an ASA5510 installation to a HA setup with a second 5510. The old 5510 has an "AnyConnect for Mobile" license which isn't being used. So we upgrade that one to a SecPlus License to enable failover posibilities and we bought a new 5510 also with a SecPlus license. When I'm trying to enable failover I get the message that my mate hasn't got the "AnyConnect for Mobile" license. I know for failover both devices must be exactly the same (at first i thougth that the AnyConnect license would be lost when upgrading to SecPlus). So now I'm wondering and searching for solutions to remove the AnyConnect license (because we don't use it).
View 7 Replies View RelatedSecurity / Firewalls :: Adding Servers To Tor To Remove Country Restriction?
Apr 10, 2011Iam trying to add servers to Tor (torproject.org) to remove country restrictions on videos from different websites such as bbc.com and i don't know how to do it. I got the server but I don't know what do do next?
View 1 Replies View RelatedCisco Security :: ASA5520 How To Proceed To Get K9 Software
Feb 26, 2013I have an ASA 5520 K8 with a smartnet contract, how can I proceed to get K9 software so that I will be able to use 3DES/AES encryption key.
View 1 Replies View RelatedCisco Switching/Routing :: WS-6748-GE How To Remove Old Configuration Of Previous Modules
Jan 23, 2011We currently have two 6509's running in VSS, both switches have a WS-6748-GE module in slot 3. I'm in the processing of removing these modules. I will then be replacing them with a different module type, but I need to know how to remove the old configuration of the previous modules.
View 4 Replies View RelatedCisco VPN :: ASA5520 / L2L VPN Security Level Higher To Lower?
Feb 3, 2011We have an ASA5520 firewall, IOS 8.0(4), running in routed mode with an operational Cisco 2821 router to ASA-5520 L2L IPsec VPN.:All Internet searches explain how to enable a L2L IPsec VPN from the LOWER security-level interface to a HIGHER security-level interface- and this is how our setup is configured and it is operational and working fine.:We now have a need to setup another L2L IPsec VPN tunnel on the same firewall BUT this time traffic will be arriving on the HIGHER security-level interface destination is to a LOWER security-level interface.:Is it possible to enable a L2L IPsec VPN tunnel between a HIGHER security-level interface to a LOWER security-level interface?
View 5 Replies View RelatedCisco Firewall :: ASA5520 Basic Configuration
May 21, 2012This is my 1st time trying to configure an ASA.
I'm trying to establish a very basic connection (ping) between 2 laptops, one sat on the outside interface, and one on the inside as per the diagram below:
I can ping back and forth from the ASA to 192.168.1.4, and to 10.1.1.1. However, what I'm trying to achieve is to be able to ping from 10.1.1.1 to 192.168.1.4 and vice versa.
I have attached the configuration file with this post as well.
Cisco Security :: ASA5520 Replace A Fortigate 310B With Products
Aug 4, 2011i need replace a Fortigate 310B with Cisco products, that is, all Web Filtering, IPS/IDS, AV, so, the question is, what we can use to replace?First, we can use Cisco ASA 5520 right? with CSC Module, so, this for Anti-X, but for IPS? is better router with IPS on IOS? or IPS Sensor? or other Cisco ASA with IPS Module?
View 3 Replies View RelatedCisco Firewall :: Security Context License Requirement - ASA5520
Jan 14, 2013A simple question - I have ASA 5520s and was wondering what license is required to create multiple (more than default 2) security contexts.
The ASA already have ASA 5520 VPN Plus license.
Software Version 8.4(1)
Cisco Firewall :: Getting ASA5520 Total Configuration Dump?
Oct 9, 2011We have a pair of ASA5520 firewalls setup in a very inefficient fashion, and I wish to convert them to an active/passive cluster. Trouble is, there are a number of configuration option I will need to re-implement (VPN tunnels, remote users etc), and trying to capture the configuation with a simple "show running-config" or "show running-config all" or even "show startup-config" doesn't get me things like the pre-shared-key from the VPN configurations - and I don't know them all, so I can't simply re-enter them.Is there any way to get a dump of the running (or startup) config which shows the hidden settings like pre-shared keys and OSPF message digest keys?
View 5 Replies View RelatedCisco VPN :: ASA5520 - Migrate Configuration / Certificates And Private Keys?
Apr 1, 2013I am going to migrate an ASA5520 with another one having VPN configuration+certificates etc. I am a bit concern about the certificates. Shall I need a new certificate because of new IP addresses on the new ASA ? Should I configure the same IP in order to avoid this. There are many VPN clients with public keys that also need to change. Is there any way for minimal changes for migration ?
View 4 Replies View RelatedCisco Security :: ASA5520 Send Traffic To SSM Module / Internet Connection Becomes Slow
Jun 8, 2011I have installed CSC-SSM-10 on cisco ASA 5520.I am facing two problems
1 : When I send traffic from ASA to SSM module then internet connection becomes slow and sometimes internet session disconnected.
2. When I try to manual update then following erros shows please see attachment .
Cisco Firewall :: ASA5520 Unit Not Accessible On Network For Initial Configuration
Dec 15, 2011We received an ASA5520-K8 through Cisco's Loan program so we could demo it as a replacement for our aging Cisco 3005 VPN appliances. Given that we are a non Cisco shop (except for specific appliances like concentrators and wireless access points), I don't have a great deal of experience with Cisco gear.I started to set to setup the appliance this morning but immediately ran into issues. The 5520 doesnt seem to be acting as a DHCP server, and worse yet, I can't access the unit even if I hard code the IP on the PC being used for configuration. I have to say that I feel kinda stupid having to post this, since I actually followed the documentation avaiable for this menial task and I fully expect the problem to be a simple one. Namely, I am using two specific sources of info for connections.
View 20 Replies View RelatedCisco Firewall :: ASA5520 Configured NAT / ACL With Real IP In Existing Configuration After Upgrade
Mar 7, 2011I am forced to upgrade my ASA 5520 software from 7.1 - 8.2 or higher, as I am not familiar with ASA I need expert opinions.I have following concerns regarding the upgrade.
1-Do I need to worry about the software licensing when I download 8.2
2-I read about the few difference in commands (ACL and NAT) in 8.2 what exactly I have to do here should I change the configured NAT and ACL with real IP in the existing configuration after the upgrade ?
Cisco Firewall :: Migrating PIX515E To ASA5520 - Update BIN Files In Configuration For ASA?
Jul 18, 2011I am in the process of migrating my config from my PIX running 8.0(4) to my ASA5520 running 8.2(1). I have converted the config so that it is ready for the ASA. I noticed the "boot system flash:" and "asdm image flash:" command references the old PIX files. Do I need to update these or will they be updated when the ASA reboots with the new config?
View 2 Replies View RelatedCisco Security :: ASA 5505 - Disk0 Error (No Such File Or Directory)
Jul 19, 2011I recently had some trouble with my ASA 5505 in that the running config would not be saved after a reboot. Definitely looked like a hardware problem with the flash memory. I have since bought a new flash memory card and copied the contents of the old card to the new card. 1st problem I have is that I can see the image on the new card, but for some reason it wont boot into that image. I get /file not found
I then successfully load a new image to the device and it boots successfully. I then follow it with a
Cisco asa# config t
Cisco(config)# boot system disk0:/asa831-k8.bin
(to ensure it boots from the flash in the future) and I get
WARNING: BOOT variable added, but unable to find disk0:/asa831-k8.bin
I have since tried
ciscoasa# fsck disk0:
Unsupported file system type!
%Error checking disk0: (No such file or directory)
When ever I try to do anything with Disk0: i get the same error. (No such file or directory). I have also tried putting the old flash card in the ASA and I now get the same response.
Pulling Configuration File From HP 2900-48G?
Jan 3, 2013is there a way to pull the config file from this? I tried looking through console mode, but was not able to find an option for it. Or is it just not possible?
View 1 Replies View RelatedSecurity / Firewalls :: Copy File In Local Network?
Jan 16, 2013copy or move into local area network? If any software to check which PC or Workstation or Users or IP to do this.
View 2 Replies View RelatedCisco Wireless :: To Download Configuration File Of WLC 4400
Jul 22, 2006If already saved the configuration file of a WLC 4400 to a server using TFTP? What is the name of the configuration file?
View 2 Replies View RelatedCisco Routers :: RV082 V3 - View Configuration File?
Feb 27, 2013Currently, the backup config is not human readable...any way to convert this?
View 1 Replies View RelatedCisco WAN :: 2950 Switch Receive Configuration File From ISP?
Aug 28, 2012At home I have a perfectly working test setup for more than 1 year now , but yesterday we had a power down for about 10 minutes in the whole area , after this power down nothing was working in my network any longer.
My Network is has follow :
ISP(Cable Modem) on FA23 from the CISCO 2950 SWITCH (24 Ports)
ROUTER (ON A STICK) on FA24 from the CISCO 2950 SWITCH
And the rest of the switch is FA1=VLAN 1; FA2=VLAN 2;FA10=VLAN 10
Our home network is connected to VLAN 10 with a IP Range of 192.168.10.x /24 After this power down , I was not able to look into the SWITCH via FA1 , the FIX IP in this switch was 192.168.1.251/24, the ONLY way to get access was via the consol port !!!What a suprice when I connected my consol to the PC , I can see ROUTER_F342 , my router config is called ROUTER1841 and my switch config name is /was called SW24.So it seems that after this Power Down , the router took or received a config from my provider ?!?
I have recovered the the file in the switch + the vlan.dat and now everithing works again.
How can I avoid that this switch receive again a wrong file , I have all the needed files on the products itself and I do not use a TFTP server.
I have atached some screen shot when my switch is starting up , and it seems that the switch receive a IP address from my ISP , I do not know why, in the config file I have given it a FIX IP 192.168.1.251/24 ?!?So it seems that my ISP erase the config file and when the switch is empty ,the swich look for :
tftp://255.255.255.255/router-confg
tftp://255.255.255.255/ciscortr.cfg
Etc ....
Until it find something.
I have tried after a complete recovery to switch off the power again for 10 minutes (ISP MODEM + SWITCH + ROUTER) and I was not able to reproduce the fault.Can it be that due to this power failure in our area that some routers or switches send or broadcast this kind of things ?
Cisco Infrastructure :: Export Objects (net And Security) From ASA 5500 Firewall To CSV File?
Feb 14, 2012how to export objects (net and security) from an ASA 5500 firewall to a .csv file?
View 1 Replies View RelatedCopying Configuration File To Usb Storage Device?
Jul 6, 2012How do i copy the configuration file from a switch to a storage device (USB)
View 1 Replies View RelatedD-Link DIR-655 :: What Is The Path Or File Name For Saved Configuration
Mar 15, 2011What is the name or path for the file stored on your hard drive for the configuration settings?
View 7 Replies View RelatedD-Link DIR-825 :: Possible To Load Configuration From Saved File
Nov 10, 2011Is it possible to load the configuration from a saved configuration file from a DIR-625 to a DIR-825? If so, what steps are required?
View 1 Replies View RelatedCisco Firewall :: ASA5520 - Active / Active Failover In Multiple Security Contexts With Dual ISP?
Jun 1, 2011I have an ASA5520 in location A with an ISP connection and a matching ASA5520 in location B with a separate ISP connection. We have fiber connecting the two locations and vlans passing back and forth so I will be able to configure the failover via a vlan as well as extend the ISP's to each location via vlans. The Active/Active configuration with the multiple security contexts does not seem to be an issue but how is a redundant ISP configured in this mode?We want to have context A using the ASA in location A with ISP1 as the primary and failing over to ISP 2 in locaiton B We also want to have context B using the ASA in location B with ISP 2 as the primary and failing over to ISP1 in location A Would route tracking provide the desired result? Is there a better option?
View 1 Replies View Related