Pulling DHCP From Cable Modem Instead Of Wireless Router?
Mar 2, 2013
I have desktops hardwired to a switch, which is connected to my cable modem. They pull a 10.x.x.x ip address with DHCP. I have a wireless modem (e3200) connected to the cable modem. My wireless devices pull a 198.x.x.x ip address. Can connect to the internet just fine, BUT..Because of this (im assuming) I cannot add my printer to my wireless laptop. Different networks, wont connect via share name etc.So, if i turn off DHCP and NAT on the wireless router, shouldnt my laptop pull DHCP from the cable modem and get a 10.x.x.x IP address while connected wirelessly?My wired computers can connect to the shared printer just fine, only my wireless computers cannot. I have another printer that is networked (connected directly to the switch, no computer) with a static ip of 10.x.x.199. My laptop can connect and print to it just fine. I just cant connect to the printer that is attached to the 10.x.x.x computer.
I have a Cisco SG 300 28 port switch that I have set in Layer 3 mode. I set up a second VLAN on it (vlan 4). I also set up the scope for DHCP on a Windows server for both VLAN's. The problem I am having, is that VLAN 4 is not pulling DHCP at all. The DHCP server is connected to port 1 on the switch, and the specifics are as follows:
I have Multiwan router with 1 port WAN and 4 DHCP Cable modem connected to SF 300-8. I want to connect 4 modem via VLAN through switch. I define Vlan2,3,4,5 on router also in Switch. port 1 on the router as trunk and the other port 2,3,4,5 as Vlan2,3,4,5 with VLAN mode Access. I tag port 1 on every VLAN also Untagged for each port. I having problem when I check the status from multiwan router. all IP address is the same (duplicate). what I want is each VLAN has own DHCP Address. Is that any miss configuration ?
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
I have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
I have a couple 1130AG switches. I'm trying to pull an image file from the flash on a Cisco Air AP1131AG. The file is c1130-k9w8-mx.124-23c.JA4.tar. The issue that I'm seeing is, I do not see a copy command to go through the tftp process. I've tried to use tftpd32 and enter the IP of the AP as the remote host, but that is not working either. Do I need to connect an ethernet cable straight to the AP in order to use Tftpd32, or can I use a console cable?
I'm switching to cable internet service instead of DSL. My Netgear router will not work with my cable modem; but it works like a charm with my DSL modem. Is it a problem with the router setup? Good thing I still have the DSL service.
Region : Australia Model : TD-W8950ND Hardware Version : V1 Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
Have had ADSL installed through a router, connected the wireless router and it works fine Have since connected the original router via -120mtrs of CAT5 cable to extend to the house. Connection through LAN is fine into desktop however the minute we try to connect an additional wireless router the connection fails. We have even put the LAN from the second Wireless into the desktop and there is no connectivity.We have had a technician come to sort the problem, they advise that they have no explanation as to why the LAN works from the distance but the wireless does not. They have suggested that we need to cut the CAT5 half way and put an antenna up to connect the two routers.
I am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
Our router is connected through a cable modem and If I connect my computer directly wired to the cable modem, I have no problem, it does not disconnect at all.In comes the router in between, when I connect the router and connect my computer through the router WRT54G2, it works initially then I get disconnected after about 1-2 hours. This is very regular. I have a temporary solution by resetting the router via two ways:
1. Go to the admin page, and perform a release and renew IP method.
I have an EA2700 (fimware "classic" 1.0.14.129982) that used to work perfectly fine with a Comcast cable modem. I just recently switched to Charter with an Arris TM902 modem and that's where the problems started. The cable modem will not recognize my router. I have to plug in a computer into the cable model when it starts up. Then I need to clone the MAC address and restart the router (after disconnecting the computer). Why isn't the cable modem recognizing the router when I restart it? I guess this could work if it would be a one time thing but I had to power-cycle the modem and it stopped recognizing the router even with the cloned MAC address. So I had to do the whole spiel again.
Is there any way to make this work easier? Should I update my router's firmware to the "smart" one?
I have a Linksys WRT54GS, version 6 with Mac OS X (version 10.6.8) hooked up to a Scientific Atlantic cable modem, with RCN as the ISP.
Recently, RCN had some network issues, and so I had to power down and reset my modem. The modem is working fine now -- no problems at all when the Mac is connected direclty to the modem.
The router's network is OK in that I can connect the Mac wirelessly to the network, but I can't connect to the internet through the router (through neither the wireless or wired connection).
I have downloaded the latest firmware update for the router, following the Linksys site instructions.
I did call Linksys tech support on the advice of RCN, and they said that the router does appear to be working (power, WLAN, and Internet lights are on), but they would be charging me nearly the cost of a new router to fix the problem.
I want to create a DMZ by having a less sophisticated router connected to cable modem, which would have the webserver which contains no sensitive information, and then the EA3500 to which my laptops and desktops which contain sensitive information would connect to. Can CCC work through that first router?
Reset to factory defaults. DHCP turned on. Status page shows black for router IP, gateway, and DNS addresses. Powered router+cable modem on/off multiple times already. I also have another wifi router (WRT120N) and it works fine.
Pretty simple connection. Just a ethernet cable between the cable modem and E1200 internet port (Cable modem <---> E1200)
I have a need to have 2 seperate networks from my comcast cable modem.I was hoping to plug a 5 port hub into the cable modem and then plug both the wrt610n and the wrt54g into the hub. Seem that only one of the routers will get an ip assigned from Comcast.Is there a way to have one ISP cable modem and create two different home networks with the two linksys routers, thus two separate independent networks?
-Network 1: public household use and family (Jane's wireless laptop, household PC's etc).
-Network 2: private household/company use and separate from the public family network (company wireless laptop/company PC, un-secure media server).
I am using wag120n modem router but is confused abt how to setup it's wireless security.The wireless securit setting recommended in tutorial given here is very different from what is given in my routrs setting up page.
I don't know how to handle the key renewal option.If i leave it as 3600 seconds does that mean i have to enter a new key in my wireless device connected to the router after every 1 hour?
I just switched to Roadrunner Lightening via Brighthouse Networks. There is no configuration capability in the Cable modem/ router / wireless - Ubee provided to make the Modem a bridge. You have to call Brighthouse to do that. They indicated that they only do that for supported routers and the EA 4500 is not one of them. I'm ready to call them to say I have one of the supported modems so "do it" and then find out what happens.
Meanwhile I have connected my EA4500 through their router and have a network in a network. I've noticed another more significant problem. The speeds through the EA 4500 drop to 90%. Is there something wrong with the router configuration that would cause this significant drop in speed? I'm afraid if the problem is the EA 4500.
i have an e3000 linksys cisco router. i havent had any problems before until i tried adding a new computer via cat5e ethernet cable. The first computer always is connected fine whether i unplug the router or modem in any order and replug. i dont know much how to fix this. ive tried some unplugging method once but it only worked until i turned the computer off and back on later. i am also running 2 xboxs with no trouble. i used cisco connect to diagnose problem but it just told me to unplug modem power and tv cable and i did that with no luck.although i have good equipment, the internet is pretty slow.i have the best service of my provider that states it has upto 50 mpbs download speed.i ran the cisco internet speed test and only got a max of 20 download and 5 upload.how could i speed this up?
We have a E3200 wireless router but our only connection is wireless. There is no Ethernet connection or cable modem. Presently I am unable to bring up the web page ie...10.100.x.x for entering the id/pw to login. Router is setup with default settings. Is there a setting that needs to be changed from the setup menu or this type of setup will not work with this router.
Attempting to get EA6500 working with TWC Motorola Surfboard SBV5220 modem, which has been working just fine for the last 2 years with a Linksys E3000 router. DHCP client in the EA6500 either doesn't ask for an IP address from the cable modem or the modem just isn't supplying one. With the E3000, you could see the IP address assigned by the cable modem and the primary and secondary DNS server addresses provided, and if the DHCP request didn't work, these addresses would be all zeroes. But, with the EA6500, I can't find an equivalent screen that shows these assignments, or zeroes when the DHCP request fails.
I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.
I have one interface setup to a Cisco 2921 router connected to a Cable modem.DHCP is on the 2921.when I connect to the ssid for my guest i'm redirected to the authentification portal 1.1.1.1 .i'm putting valide credential and when pressing the submit button .. it just go anywhere.
I have setup another SSID with a psk and it's working fine.. getting ip and able to browse internet.From what i have read... it's apparently DNS issue on my router.. but what should I check.
I cannot access my Motorola SB6141 cable modem status page at 192.168.100.1 thru the EA6500 router. I can bypass the router and can connect to the status page with no problem. Is there a setting to change or can I possibly do port forwarding to access it?
I am recieving error 619 (port for connection was closed) when trying to connect over my wireless connection. If I disconnect the WRT54G and hard wire to the cable modem I can VPN in without a problem. I have enabled IPSec / PPTP / L2TP on the VPN security tab and have reset the wireless modem.
Upgraded my E3000 from 1.0.02 to 1.0.04 and now I cant get an ip from my arris modem. I did the 30/30/30 reset and everything but no luck. I've had to plug the modem directly into the computer for now. Where can I find the 1.0.02 download or how can I fix this?
I recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
My home lab is in a different room than the cable modem. I have a wireless N router in the room with the cable modem. I have a wireless access point that is connected to a Cisco 2611XM routers fa0/0 interface. The 2611 accepts the DHCP address from the wireless router. However, I can't ping past the wireless LAN 192.168.10.0 network. I know with the wireless router it's two layers of DHCP. Should remove the DHCP settings from the wireless router? The wireless router is a TrendNet TEW-651BR. I can ping my iphone or any device conntected to the wireless router. And my laptop can ping default gateway of the wireless router, which I assume is the cable modem, however the 2611 cannot. So I'm assuming that's why the hosts behind the 2611 can't get to the internet. I followed the below instructions. I know the instructions don't assume your using a wirelss router between 2611 and the cable modem. But, I really don't want to run a cable to the cable modem.
